module_param_named(noleds, modparam_noleds, int, 0444);
MODULE_PARM_DESC(noleds, "Turn off all LED activity");
-#ifdef CONFIG_BCM43XX_DEBUG
static char modparam_fwpostfix[64];
module_param_string(fwpostfix, modparam_fwpostfix, 64, 0444);
-MODULE_PARM_DESC(fwpostfix, "Postfix for .fw files. Useful for debugging.");
-#else
-# define modparam_fwpostfix ""
-#endif /* CONFIG_BCM43XX_DEBUG*/
+MODULE_PARM_DESC(fwpostfix, "Postfix for .fw files. Useful for using multiple firmware image versions.");
/* If you want to debug with just a single device, enable this,
if (err)
goto err_gpio_cleanup;
bcm43xx_radio_turn_on(bcm);
+ bcm->radio_hw_enable = bcm43xx_is_hw_radio_enabled(bcm);
+ dprintk(KERN_INFO PFX "Radio %s by hardware\n",
+ (bcm->radio_hw_enable == 0) ? "disabled" : "enabled");
bcm43xx_write16(bcm, 0x03E6, 0x0000);
err = bcm43xx_phy_init(bcm);
err = bcm43xx_pctl_set_crystal(bcm, 1);
if (err)
goto out;
- bcm43xx_pci_read_config16(bcm, PCI_STATUS, &pci_status);
- bcm43xx_pci_write_config16(bcm, PCI_STATUS, pci_status & ~PCI_STATUS_SIG_TARGET_ABORT);
+ err = bcm43xx_pci_read_config16(bcm, PCI_STATUS, &pci_status);
+ if (err)
+ goto out;
+ err = bcm43xx_pci_write_config16(bcm, PCI_STATUS, pci_status & ~PCI_STATUS_SIG_TARGET_ABORT);
out:
return err;
}
static void bcm43xx_periodic_every15sec(struct bcm43xx_private *bcm)
+{
+ bcm43xx_phy_xmitpower(bcm); //FIXME: unless scanning?
+ //TODO for APHY (temperature?)
+}
+
+static void bcm43xx_periodic_every1sec(struct bcm43xx_private *bcm)
{
struct bcm43xx_phyinfo *phy = bcm43xx_current_phy(bcm);
struct bcm43xx_radioinfo *radio = bcm43xx_current_radio(bcm);
+ int radio_hw_enable;
+ /* check if radio hardware enabled status changed */
+ radio_hw_enable = bcm43xx_is_hw_radio_enabled(bcm);
+ if (unlikely(bcm->radio_hw_enable != radio_hw_enable)) {
+ bcm->radio_hw_enable = radio_hw_enable;
+ dprintk(KERN_INFO PFX "Radio hardware status changed to %s\n",
+ (radio_hw_enable == 0) ? "disabled" : "enabled");
+ bcm43xx_leds_update(bcm, 0);
+ }
if (phy->type == BCM43xx_PHYTYPE_G) {
//TODO: update_aci_moving_average
if (radio->aci_enable && radio->aci_wlan_automatic) {
//TODO: implement rev1 workaround
}
}
- bcm43xx_phy_xmitpower(bcm); //FIXME: unless scanning?
- //TODO for APHY (temperature?)
}
static void do_periodic_work(struct bcm43xx_private *bcm)
{
- if (bcm->periodic_state % 8 == 0)
+ if (bcm->periodic_state % 120 == 0)
bcm43xx_periodic_every120sec(bcm);
- if (bcm->periodic_state % 4 == 0)
+ if (bcm->periodic_state % 60 == 0)
bcm43xx_periodic_every60sec(bcm);
- if (bcm->periodic_state % 2 == 0)
+ if (bcm->periodic_state % 30 == 0)
bcm43xx_periodic_every30sec(bcm);
- bcm43xx_periodic_every15sec(bcm);
+ if (bcm->periodic_state % 15 == 0)
+ bcm43xx_periodic_every15sec(bcm);
+ bcm43xx_periodic_every1sec(bcm);
- schedule_delayed_work(&bcm->periodic_work, HZ * 15);
+ schedule_delayed_work(&bcm->periodic_work, HZ);
}
static void bcm43xx_periodic_work_handler(struct work_struct *work)
unsigned long orig_trans_start = 0;
mutex_lock(&bcm->mutex);
- if (unlikely(bcm->periodic_state % 4 == 0)) {
+ if (unlikely(bcm->periodic_state % 60 == 0)) {
/* Periodic work will take a long time, so we want it to
* be preemtible.
*/
do_periodic_work(bcm);
- if (unlikely(bcm->periodic_state % 4 == 0)) {
+ if (unlikely(bcm->periodic_state % 60 == 0)) {
spin_lock_irqsave(&bcm->irq_lock, flags);
tasklet_enable(&bcm->isr_tasklet);
bcm43xx_interrupt_enable(bcm, savedirqs);
}
net_dev->base_addr = (unsigned long)bcm->mmio_addr;
- bcm43xx_pci_read_config16(bcm, PCI_SUBSYSTEM_VENDOR_ID,
+ err = bcm43xx_pci_read_config16(bcm, PCI_SUBSYSTEM_VENDOR_ID,
&bcm->board_vendor);
- bcm43xx_pci_read_config16(bcm, PCI_SUBSYSTEM_ID,
+ if (err)
+ goto err_iounmap;
+ err = bcm43xx_pci_read_config16(bcm, PCI_SUBSYSTEM_ID,
&bcm->board_type);
- bcm43xx_pci_read_config16(bcm, PCI_REVISION_ID,
+ if (err)
+ goto err_iounmap;
+ err = bcm43xx_pci_read_config16(bcm, PCI_REVISION_ID,
&bcm->board_revision);
+ if (err)
+ goto err_iounmap;
err = bcm43xx_chipset_attach(bcm);
if (err)
pci_release_regions(pci_dev);
err_pci_disable:
pci_disable_device(pci_dev);
+ printk(KERN_ERR PFX "Unable to attach board\n");
goto out;
}