Please submit bugs to http://bugzilla.kernel.org/ .
*/
+#define pr_fmt(fmt) "tulip: " fmt
#define DRV_NAME "tulip"
#ifdef CONFIG_TULIP_NAPI
module_param_array(options, int, NULL, 0);
module_param_array(full_duplex, int, NULL, 0);
-#define PFX DRV_NAME ": "
-
#ifdef TULIP_DEBUG
int tulip_debug = TULIP_DEBUG;
#else
udelay(100);
if (tulip_debug > 1)
- printk(KERN_DEBUG "%s: tulip_up(), irq==%d\n",
- dev->name, dev->irq);
+ netdev_dbg(dev, "tulip_up(), irq==%d\n", dev->irq);
iowrite32(tp->rx_ring_dma, ioaddr + CSR3);
iowrite32(tp->tx_ring_dma, ioaddr + CSR4);
iowrite32(0, ioaddr + CSR2); /* Rx poll demand */
if (tulip_debug > 2) {
- printk(KERN_DEBUG "%s: Done tulip_up(), CSR0 %08x, CSR5 %08x CSR6 %08x\n",
- dev->name, ioread32(ioaddr + CSR0),
- ioread32(ioaddr + CSR5),
- ioread32(ioaddr + CSR6));
+ netdev_dbg(dev, "Done tulip_up(), CSR0 %08x, CSR5 %08x CSR6 %08x\n",
+ ioread32(ioaddr + CSR0),
+ ioread32(ioaddr + CSR5),
+ ioread32(ioaddr + CSR6));
}
/* Set the timer to switch to check for link beat and perhaps switch
tulip_down (dev);
if (tulip_debug > 1)
- dev_printk(KERN_DEBUG, &dev->dev,
- "Shutting down ethercard, status was %02x\n",
+ netdev_dbg(dev, "Shutting down ethercard, status was %02x\n",
ioread32 (ioaddr + CSR5));
free_irq (dev->irq, dev);
u32 csr0;
if (tulip_debug > 3)
- printk(KERN_DEBUG "%s: tulip_mwi_config()\n", pci_name(pdev));
+ netdev_dbg(dev, "tulip_mwi_config()\n");
tp->csr0 = csr0 = 0;
out:
tp->csr0 = csr0;
if (tulip_debug > 2)
- printk(KERN_DEBUG "%s: MWI config cacheline=%d, csr0=%08x\n",
- pci_name(pdev), cache, csr0);
+ netdev_dbg(dev, "MWI config cacheline=%d, csr0=%08x\n",
+ cache, csr0);
}
#endif
*/
if (pdev->subsystem_vendor == PCI_VENDOR_ID_LMC) {
- pr_err(PFX "skipping LMC card\n");
+ pr_err("skipping LMC card\n");
return -ENODEV;
} else if (pdev->subsystem_vendor == PCI_VENDOR_ID_SBE &&
(pdev->subsystem_device == PCI_SUBDEVICE_ID_SBE_T3E3 ||
pdev->subsystem_device == PCI_SUBDEVICE_ID_SBE_2T3E3_P0 ||
pdev->subsystem_device == PCI_SUBDEVICE_ID_SBE_2T3E3_P1)) {
- pr_err(PFX "skipping SBE T3E3 port\n");
+ pr_err("skipping SBE T3E3 port\n");
return -ENODEV;
}
if (pdev->vendor == 0x1282 && pdev->device == 0x9100 &&
pdev->revision < 0x30) {
- pr_info(PFX "skipping early DM9100 with Crc bug (use dmfe)\n");
+ pr_info("skipping early DM9100 with Crc bug (use dmfe)\n");
return -ENODEV;
}
dp = pci_device_to_OF_node(pdev);
if (!(dp && of_get_property(dp, "local-mac-address", NULL))) {
- pr_info(PFX "skipping DM910x expansion card (use dmfe)\n");
+ pr_info("skipping DM910x expansion card (use dmfe)\n");
return -ENODEV;
}
}
i = pci_enable_device(pdev);
if (i) {
- pr_err(PFX "Cannot enable tulip board #%d, aborting\n",
- board_idx);
+ pr_err("Cannot enable tulip board #%d, aborting\n", board_idx);
return i;
}
/* The chip will fail to enter a low-power state later unless
* first explicitly commanded into D0 */
if (pci_set_power_state(pdev, PCI_D0)) {
- printk (KERN_NOTICE PFX
- "Failed to set power state to D0\n");
+ pr_notice("Failed to set power state to D0\n");
}
irq = pdev->irq;
/* alloc_etherdev ensures aligned and zeroed private structures */
dev = alloc_etherdev (sizeof (*tp));
if (!dev) {
- pr_err(PFX "ether device alloc failed, aborting\n");
+ pr_err("ether device alloc failed, aborting\n");
return -ENOMEM;
}
SET_NETDEV_DEV(dev, &pdev->dev);
if (pci_resource_len (pdev, 0) < tulip_tbl[chip_idx].io_size) {
- pr_err(PFX "%s: I/O region (0x%llx@0x%llx) too small, aborting\n",
+ pr_err("%s: I/O region (0x%llx@0x%llx) too small, aborting\n",
pci_name(pdev),
(unsigned long long)pci_resource_len (pdev, 0),
(unsigned long long)pci_resource_start (pdev, 0));
return 0;
if ((retval = pci_enable_device(pdev))) {
- pr_err(PFX "pci_enable_device failed in resume\n");
+ pr_err("pci_enable_device failed in resume\n");
return retval;
}
if ((retval = request_irq(dev->irq, tulip_interrupt, IRQF_SHARED, dev->name, dev))) {
- pr_err(PFX "request_irq failed in resume\n");
+ pr_err("request_irq failed in resume\n");
return retval;
}