/*
* PHY drivers for the sungem ethernet driver.
- *
+ *
* This file could be shared with other drivers.
- *
- * (c) 2002, Benjamin Herrenscmidt (benh@kernel.crashing.org)
+ *
+ * (c) 2002-2007, Benjamin Herrenscmidt (benh@kernel.crashing.org)
*
* TODO:
- * - Implement WOL
* - Add support for PHYs that provide an IRQ line
* - Eventually moved the entire polling state machine in
* there (out of the eth driver), so that it can easily be
* of darwin, still need to reverse engineer that
*/
-#include <linux/config.h>
#include <linux/module.h>
{
u16 val;
int limit = 10000;
-
+
val = __phy_read(phy, phy_id, MII_BMCR);
val &= ~(BMCR_ISOLATE | BMCR_PDOWN);
val |= BMCR_RESET;
}
if ((val & BMCR_ISOLATE) && limit > 0)
__phy_write(phy, phy_id, MII_BMCR, val & ~BMCR_ISOLATE);
-
+
return (limit <= 0);
}
return 0;
}
+static int bcm5241_init(struct mii_phy* phy)
+{
+ u16 data;
+
+ data = phy_read(phy, MII_BCM5221_TEST);
+ phy_write(phy, MII_BCM5221_TEST,
+ data | MII_BCM5221_TEST_ENABLE_SHADOWS);
+
+ data = phy_read(phy, MII_BCM5221_SHDOW_AUX_STAT2);
+ phy_write(phy, MII_BCM5221_SHDOW_AUX_STAT2,
+ data | MII_BCM5221_SHDOW_AUX_STAT2_APD);
+
+ data = phy_read(phy, MII_BCM5221_SHDOW_AUX_MODE4);
+ phy_write(phy, MII_BCM5221_SHDOW_AUX_MODE4,
+ data & ~MII_BCM5241_SHDOW_AUX_MODE4_STANDBYPWR);
+
+ data = phy_read(phy, MII_BCM5221_TEST);
+ phy_write(phy, MII_BCM5221_TEST,
+ data & ~MII_BCM5221_TEST_ENABLE_SHADOWS);
+
+ return 0;
+}
+
+static int bcm5241_suspend(struct mii_phy* phy)
+{
+ u16 data;
+
+ data = phy_read(phy, MII_BCM5221_TEST);
+ phy_write(phy, MII_BCM5221_TEST,
+ data | MII_BCM5221_TEST_ENABLE_SHADOWS);
+
+ data = phy_read(phy, MII_BCM5221_SHDOW_AUX_MODE4);
+ phy_write(phy, MII_BCM5221_SHDOW_AUX_MODE4,
+ data | MII_BCM5241_SHDOW_AUX_MODE4_STANDBYPWR);
+
+ return 0;
+}
+
static int bcm5400_init(struct mii_phy* phy)
{
u16 data;
data = phy_read(phy, MII_BCM5400_AUXCONTROL);
data |= MII_BCM5400_AUXCONTROL_PWR10BASET;
phy_write(phy, MII_BCM5400_AUXCONTROL, data);
-
+
data = phy_read(phy, MII_BCM5400_GB_CONTROL);
data |= MII_BCM5400_GB_CONTROL_FULLDUPLEXCAP;
phy_write(phy, MII_BCM5400_GB_CONTROL, data);
-
+
udelay(100);
/* Reset and configure cascaded 10/100 PHY */
(void)reset_one_mii_phy(phy, 0x1f);
-
+
data = __phy_read(phy, 0x1f, MII_BCM5201_MULTIPHY);
data |= MII_BCM5201_MULTIPHY_SERIALMODE;
__phy_write(phy, 0x1f, MII_BCM5201_MULTIPHY, data);
/* Some revisions of 5401 appear to need this
* initialisation sequence to disable, according
* to OF, "tap power management"
- *
+ *
* WARNING ! OF and Darwin don't agree on the
* register addresses. OF seem to interpret the
* register numbers below as decimal
phy_write(phy, 0x17, 0x201f);
phy_write(phy, 0x15, 0x0a20);
}
-
+
/* Configure for gigabit full duplex */
data = phy_read(phy, MII_BCM5400_GB_CONTROL);
data |= MII_BCM5400_GB_CONTROL_FULLDUPLEXCAP;
/* Reset and configure cascaded 10/100 PHY */
(void)reset_one_mii_phy(phy, 0x1f);
-
+
data = __phy_read(phy, 0x1f, MII_BCM5201_MULTIPHY);
data |= MII_BCM5201_MULTIPHY_SERIALMODE;
__phy_write(phy, 0x1f, MII_BCM5201_MULTIPHY, data);
/* Reset and configure cascaded 10/100 PHY */
(void)reset_one_mii_phy(phy, 0x1f);
-
+
return 0;
}
static int bcm54xx_setup_aneg(struct mii_phy *phy, u32 advertise)
{
u16 ctl, adv;
-
+
phy->autoneg = 1;
phy->speed = SPEED_10;
phy->duplex = DUPLEX_HALF;
adv |= ADVERTISE_100HALF;
if (advertise & ADVERTISED_100baseT_Full)
adv |= ADVERTISE_100FULL;
+ if (advertise & ADVERTISED_Pause)
+ adv |= ADVERTISE_PAUSE_CAP;
+ if (advertise & ADVERTISED_Asym_Pause)
+ adv |= ADVERTISE_PAUSE_ASYM;
phy_write(phy, MII_ADVERTISE, adv);
/* Setup 1000BT advertise */
static int bcm54xx_setup_forced(struct mii_phy *phy, int speed, int fd)
{
u16 ctl;
-
+
phy->autoneg = 0;
phy->speed = speed;
phy->duplex = fd;
ctl |= BMCR_FULLDPLX;
// XXX Should we set the sungem to GII now on 1000BT ?
-
+
phy_write(phy, MII_BMCR, ctl);
return 0;
static int bcm54xx_read_link(struct mii_phy *phy)
{
- int link_mode;
+ int link_mode;
u16 val;
-
+
if (phy->autoneg) {
val = phy_read(phy, MII_BCM5400_AUXSTATUS);
link_mode = ((val & MII_BCM5400_AUXSTATUS_LINKMODE_MASK) >>
MII_BCM5400_AUXSTATUS_LINKMODE_SHIFT);
- phy->duplex = phy_BCM5400_link_table[link_mode][0] ? DUPLEX_FULL : DUPLEX_HALF;
+ phy->duplex = phy_BCM5400_link_table[link_mode][0] ?
+ DUPLEX_FULL : DUPLEX_HALF;
phy->speed = phy_BCM5400_link_table[link_mode][2] ?
SPEED_1000 :
- (phy_BCM5400_link_table[link_mode][1] ? SPEED_100 : SPEED_10);
+ (phy_BCM5400_link_table[link_mode][1] ?
+ SPEED_100 : SPEED_10);
val = phy_read(phy, MII_LPA);
- phy->pause = ((val & LPA_PAUSE) != 0);
+ phy->pause = (phy->duplex == DUPLEX_FULL) &&
+ ((val & LPA_PAUSE) != 0);
}
/* On non-aneg, we assume what we put in BMCR is the speed,
* though magic-aneg shouldn't prevent this case from occurring
return 0;
}
+static int marvell88e1111_init(struct mii_phy* phy)
+{
+ u16 rev;
+
+ /* magic init sequence for rev 0 */
+ rev = phy_read(phy, MII_PHYSID2) & 0x000f;
+ if (rev == 0) {
+ phy_write(phy, 0x1d, 0x000a);
+ phy_write(phy, 0x1e, 0x0821);
+
+ phy_write(phy, 0x1d, 0x0006);
+ phy_write(phy, 0x1e, 0x8600);
+
+ phy_write(phy, 0x1d, 0x000b);
+ phy_write(phy, 0x1e, 0x0100);
+
+ phy_write(phy, 0x1d, 0x0004);
+ phy_write(phy, 0x1e, 0x4850);
+ }
+ return 0;
+}
+
static int marvell_setup_aneg(struct mii_phy *phy, u32 advertise)
{
u16 ctl, adv;
-
+
phy->autoneg = 1;
phy->speed = SPEED_10;
phy->duplex = DUPLEX_HALF;
adv |= ADVERTISE_100HALF;
if (advertise & ADVERTISED_100baseT_Full)
adv |= ADVERTISE_100FULL;
+ if (advertise & ADVERTISED_Pause)
+ adv |= ADVERTISE_PAUSE_CAP;
+ if (advertise & ADVERTISED_Asym_Pause)
+ adv |= ADVERTISE_PAUSE_ASYM;
phy_write(phy, MII_ADVERTISE, adv);
/* Setup 1000BT advertise & enable crossover detect
static int marvell_setup_forced(struct mii_phy *phy, int speed, int fd)
{
u16 ctl, ctl2;
-
+
phy->autoneg = 0;
phy->speed = speed;
phy->duplex = fd;
phy_write(phy, MII_1000BASETCONTROL, ctl2);
// XXX Should we set the sungem to GII now on 1000BT ?
-
+
phy_write(phy, MII_BMCR, ctl);
return 0;
static int marvell_read_link(struct mii_phy *phy)
{
- u16 status;
+ u16 status, pmask;
if (phy->autoneg) {
status = phy_read(phy, MII_M1011_PHY_SPEC_STATUS);
phy->duplex = DUPLEX_FULL;
else
phy->duplex = DUPLEX_HALF;
- phy->pause = 0; /* XXX Check against spec ! */
+ pmask = MII_M1011_PHY_SPEC_STATUS_TX_PAUSE |
+ MII_M1011_PHY_SPEC_STATUS_RX_PAUSE;
+ phy->pause = (status & pmask) == pmask;
}
/* On non-aneg, we assume what we put in BMCR is the speed,
* though magic-aneg shouldn't prevent this case from occurring
static int genmii_setup_aneg(struct mii_phy *phy, u32 advertise)
{
u16 ctl, adv;
-
+
phy->autoneg = 1;
phy->speed = SPEED_10;
phy->duplex = DUPLEX_HALF;
adv |= ADVERTISE_100HALF;
if (advertise & ADVERTISED_100baseT_Full)
adv |= ADVERTISE_100FULL;
+ if (advertise & ADVERTISED_Pause)
+ adv |= ADVERTISE_PAUSE_CAP;
+ if (advertise & ADVERTISED_Asym_Pause)
+ adv |= ADVERTISE_PAUSE_ASYM;
phy_write(phy, MII_ADVERTISE, adv);
/* Start/Restart aneg */
static int genmii_setup_forced(struct mii_phy *phy, int speed, int fd)
{
u16 ctl;
-
+
phy->autoneg = 0;
phy->speed = speed;
phy->duplex = fd;
static int genmii_poll_link(struct mii_phy *phy)
{
u16 status;
-
+
(void)phy_read(phy, MII_BMSR);
status = phy_read(phy, MII_BMSR);
if ((status & BMSR_LSTATUS) == 0)
phy->speed = SPEED_100;
else
phy->speed = SPEED_10;
- phy->pause = 0;
+ phy->pause = (phy->duplex == DUPLEX_FULL) &&
+ ((lpa & LPA_PAUSE) != 0);
}
/* On non-aneg, we assume what we put in BMCR is the speed,
* though magic-aneg shouldn't prevent this case from occurring
}
-#define MII_BASIC_FEATURES (SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full | \
- SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full | \
- SUPPORTED_Autoneg | SUPPORTED_TP | SUPPORTED_MII)
-#define MII_GBIT_FEATURES (MII_BASIC_FEATURES | \
- SUPPORTED_1000baseT_Half | SUPPORTED_1000baseT_Full)
+#define MII_BASIC_FEATURES \
+ (SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full | \
+ SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full | \
+ SUPPORTED_Autoneg | SUPPORTED_TP | SUPPORTED_MII | \
+ SUPPORTED_Pause)
+
+/* On gigabit capable PHYs, we advertise Pause support but not asym pause
+ * support for now as I'm not sure it's supported and Darwin doesn't do
+ * it neither. --BenH.
+ */
+#define MII_GBIT_FEATURES \
+ (MII_BASIC_FEATURES | \
+ SUPPORTED_1000baseT_Half | SUPPORTED_1000baseT_Full)
/* Broadcom BCM 5201 */
static struct mii_phy_ops bcm5201_phy_ops = {
.ops = &bcm5221_phy_ops
};
+/* Broadcom BCM 5241 */
+static struct mii_phy_ops bcm5241_phy_ops = {
+ .suspend = bcm5241_suspend,
+ .init = bcm5241_init,
+ .setup_aneg = genmii_setup_aneg,
+ .setup_forced = genmii_setup_forced,
+ .poll_link = genmii_poll_link,
+ .read_link = genmii_read_link,
+};
+static struct mii_phy_def bcm5241_phy_def = {
+ .phy_id = 0x0143bc30,
+ .phy_id_mask = 0xfffffff0,
+ .name = "BCM5241",
+ .features = MII_BASIC_FEATURES,
+ .magic_aneg = 1,
+ .ops = &bcm5241_phy_ops
+};
+
/* Broadcom BCM 5400 */
static struct mii_phy_ops bcm5400_phy_ops = {
.init = bcm5400_init,
.ops = &bcm5462V_phy_ops
};
-/* Marvell 88E1101 (Apple seem to deal with 2 different revs,
- * I masked out the 8 last bits to get both, but some specs
- * would be useful here) --BenH.
- */
-static struct mii_phy_ops marvell_phy_ops = {
+/* Marvell 88E1101 amd 88E1111 */
+static struct mii_phy_ops marvell88e1101_phy_ops = {
+ .suspend = generic_suspend,
+ .setup_aneg = marvell_setup_aneg,
+ .setup_forced = marvell_setup_forced,
+ .poll_link = genmii_poll_link,
+ .read_link = marvell_read_link
+};
+
+static struct mii_phy_ops marvell88e1111_phy_ops = {
+ .init = marvell88e1111_init,
.suspend = generic_suspend,
.setup_aneg = marvell_setup_aneg,
.setup_forced = marvell_setup_forced,
.read_link = marvell_read_link
};
-static struct mii_phy_def marvell_phy_def = {
- .phy_id = 0x01410c00,
- .phy_id_mask = 0xffffff00,
- .name = "Marvell 88E1101",
+/* two revs in darwin for the 88e1101 ... I could use a datasheet
+ * to get the proper names...
+ */
+static struct mii_phy_def marvell88e1101v1_phy_def = {
+ .phy_id = 0x01410c20,
+ .phy_id_mask = 0xfffffff0,
+ .name = "Marvell 88E1101v1",
+ .features = MII_GBIT_FEATURES,
+ .magic_aneg = 1,
+ .ops = &marvell88e1101_phy_ops
+};
+static struct mii_phy_def marvell88e1101v2_phy_def = {
+ .phy_id = 0x01410c60,
+ .phy_id_mask = 0xfffffff0,
+ .name = "Marvell 88E1101v2",
.features = MII_GBIT_FEATURES,
.magic_aneg = 1,
- .ops = &marvell_phy_ops
+ .ops = &marvell88e1101_phy_ops
+};
+static struct mii_phy_def marvell88e1111_phy_def = {
+ .phy_id = 0x01410cc0,
+ .phy_id_mask = 0xfffffff0,
+ .name = "Marvell 88E1111",
+ .features = MII_GBIT_FEATURES,
+ .magic_aneg = 1,
+ .ops = &marvell88e1111_phy_ops
};
/* Generic implementation for most 10/100 PHYs */
static struct mii_phy_def* mii_phy_table[] = {
&bcm5201_phy_def,
&bcm5221_phy_def,
+ &bcm5241_phy_def,
&bcm5400_phy_def,
&bcm5401_phy_def,
&bcm5411_phy_def,
&bcm5421k2_phy_def,
&bcm5461_phy_def,
&bcm5462V_phy_def,
- &marvell_phy_def,
+ &marvell88e1101v1_phy_def,
+ &marvell88e1101v2_phy_def,
+ &marvell88e1111_phy_def,
&genmii_phy_def,
NULL
};
* may re-probe the PHY regulary
*/
phy->mii_id = mii_id;
-
+
/* Take PHY out of isloate mode and reset it. */
rc = reset_one_mii_phy(phy, mii_id);
if (rc)
goto fail;
- /* Read ID and find matching entry */
+ /* Read ID and find matching entry */
id = (phy_read(phy, MII_PHYSID1) << 16 | phy_read(phy, MII_PHYSID2));
printk(KERN_DEBUG "PHY ID: %x, addr: %x\n", id, mii_id);
for (i=0; (def = mii_phy_table[i]) != NULL; i++)
goto fail;
phy->def = def;
-
+
return 0;
fail:
phy->speed = 0;
git.openpandora.org / pandora-kernel.git / blobdiff