Support information and updates available at
http://www.scyld.com/network/netsemi.html
+ [link no longer provides useful info -jgarzik]
- Linux kernel modifications:
-
- Version 1.0.1:
- - Spinlock fixes
- - Bug fixes and better intr performance (Tjeerd)
- Version 1.0.2:
- - Now reads correct MAC address from eeprom
- Version 1.0.3:
- - Eliminate redundant priv->tx_full flag
- - Call netif_start_queue from dev->tx_timeout
- - wmb() in start_tx() to flush data
- - Update Tx locking
- - Clean up PCI enable (davej)
- Version 1.0.4:
- - Merge Donald Becker's natsemi.c version 1.07
- Version 1.0.5:
- - { fill me in }
- Version 1.0.6:
- * ethtool support (jgarzik)
- * Proper initialization of the card (which sometimes
- fails to occur and leaves the card in a non-functional
- state). (uzi)
-
- * Some documented register settings to optimize some
- of the 100Mbit autodetection circuitry in rev C cards. (uzi)
-
- * Polling of the PHY intr for stuff like link state
- change and auto- negotiation to finally work properly. (uzi)
-
- * One-liner removal of a duplicate declaration of
- netdev_error(). (uzi)
-
- Version 1.0.7: (Manfred Spraul)
- * pci dma
- * SMP locking update
- * full reset added into tx_timeout
- * correct multicast hash generation (both big and little endian)
- [copied from a natsemi driver version
- from Myrio Corporation, Greg Smith]
- * suspend/resume
-
- version 1.0.8 (Tim Hockin <thockin@sun.com>)
- * ETHTOOL_* support
- * Wake on lan support (Erik Gilling)
- * MXDMA fixes for serverworks
- * EEPROM reload
-
- version 1.0.9 (Manfred Spraul)
- * Main change: fix lack of synchronize
- netif_close/netif_suspend against a last interrupt
- or packet.
- * do not enable superflous interrupts (e.g. the
- drivers relies on TxDone - TxIntr not needed)
- * wait that the hardware has really stopped in close
- and suspend.
- * workaround for the (at least) gcc-2.95.1 compiler
- problem. Also simplifies the code a bit.
- * disable_irq() in tx_timeout - needed to protect
- against rx interrupts.
- * stop the nic before switching into silent rx mode
- for wol (required according to docu).
-
- version 1.0.10:
- * use long for ee_addr (various)
- * print pointers properly (DaveM)
- * include asm/irq.h (?)
-
- version 1.0.11:
- * check and reset if PHY errors appear (Adrian Sun)
- * WoL cleanup (Tim Hockin)
- * Magic number cleanup (Tim Hockin)
- * Don't reload EEPROM on every reset (Tim Hockin)
- * Save and restore EEPROM state across reset (Tim Hockin)
- * MDIO Cleanup (Tim Hockin)
- * Reformat register offsets/bits (jgarzik)
-
- version 1.0.12:
- * ETHTOOL_* further support (Tim Hockin)
-
- version 1.0.13:
- * ETHTOOL_[G]EEPROM support (Tim Hockin)
-
- version 1.0.13:
- * crc cleanup (Matt Domsch <Matt_Domsch@dell.com>)
-
- version 1.0.14:
- * Cleanup some messages and autoneg in ethtool (Tim Hockin)
-
- version 1.0.15:
- * Get rid of cable_magic flag
- * use new (National provided) solution for cable magic issue
-
- version 1.0.16:
- * call netdev_rx() for RxErrors (Manfred Spraul)
- * formatting and cleanups
- * change options and full_duplex arrays to be zero
- initialized
- * enable only the WoL and PHY interrupts in wol mode
-
- version 1.0.17:
- * only do cable_magic on 83815 and early 83816 (Tim Hockin)
- * create a function for rx refill (Manfred Spraul)
- * combine drain_ring and init_ring (Manfred Spraul)
- * oom handling (Manfred Spraul)
- * hands_off instead of playing with netif_device_{de,a}ttach
- (Manfred Spraul)
- * be sure to write the MAC back to the chip (Manfred Spraul)
- * lengthen EEPROM timeout, and always warn about timeouts
- (Manfred Spraul)
- * comments update (Manfred)
- * do the right thing on a phy-reset (Manfred and Tim)
-
TODO:
* big endian support with CFG:BEM instead of cpu_to_le32
*/
#include <asm/uaccess.h>
#define DRV_NAME "natsemi"
-#define DRV_VERSION "1.07+LK1.0.17"
-#define DRV_RELDATE "Sep 27, 2002"
+#define DRV_VERSION "2.1"
+#define DRV_RELDATE "Sept 11, 2006"
#define RX_OFFSET 2
module_param_array(full_duplex, int, NULL, 0);
MODULE_PARM_DESC(mtu, "DP8381x MTU (all boards)");
MODULE_PARM_DESC(debug, "DP8381x default debug level");
-MODULE_PARM_DESC(rx_copybreak,
+MODULE_PARM_DESC(rx_copybreak,
"DP8381x copy breakpoint for copy-only-tiny-frames");
-MODULE_PARM_DESC(options,
+MODULE_PARM_DESC(options,
"DP8381x: Bits 0-3: media type, bit 17: full duplex");
MODULE_PARM_DESC(full_duplex, "DP8381x full duplex setting(s) (1)");
MII_EN_SCRM = 0x0004, /* enable scrambler (tp) */
};
-
+
/* array of board data directly indexed by pci_tbl[x].driver_data */
static const struct {
const char *name;
TxCarrierIgn = 0x80000000
};
-/*
+/*
* Tx Configuration:
* - 256 byte DMA burst length
* - fill threshold 512 bytes (i.e. restart DMA when 512 bytes are free)
static int netdev_close(struct net_device *dev);
static int netdev_get_regs(struct net_device *dev, u8 *buf);
static int netdev_get_eeprom(struct net_device *dev, u8 *buf);
-static struct ethtool_ops ethtool_ops;
+static const struct ethtool_ops ethtool_ops;
static inline void __iomem *ns_ioaddr(struct net_device *dev)
{
void __iomem *ioaddr = ns_ioaddr(dev);
int target = 31;
- /*
+ /*
* The internal phy is visible on the external mii bus. Therefore we must
* move it away before we can send commands to an external phy.
* There are two addresses we must avoid:
tmp |= BMCR_SPEED100;
if (np->duplex == DUPLEX_FULL)
tmp |= BMCR_FULLDPLX;
- /*
+ /*
* Note: there is no good way to inform the link partner
* that our capabilities changed. The user has to unplug
* and replug the network cable after some changes, e.g.
writel(cfg, ioaddr + ChipConfig);
readl(ioaddr + ChipConfig);
udelay(1);
-
+
/* 2) reset the internal phy: */
bmcr = readw(ioaddr+BasicControl+(MII_BMCR<<2));
writel(bmcr | BMCR_RESET, ioaddr+BasicControl+(MII_BMCR<<2));
/* Switch to external phy */
did_switch = switch_port_external(dev);
-
+
/* Scan the possible phy addresses:
*
* PHY address 0 means that the phy is in isolate mode. Not yet
/* Reset the chip, just in case. */
natsemi_reset(dev);
- i = request_irq(dev->irq, &intr_handler, SA_SHIRQ, dev->name, dev);
+ i = request_irq(dev->irq, &intr_handler, IRQF_SHARED, dev->name, dev);
if (i) return i;
if (netif_msg_ifup(np))
void __iomem * ioaddr = ns_ioaddr(dev);
int duplex;
u16 bmsr;
-
+
/* The link status field is latched: it remains low after a temporary
* link failure until it's read. We need the current link status,
* thus read twice.
if (np->hands_off)
return IRQ_NONE;
-
+
/* Reading automatically acknowledges. */
np->intr_status = readl(ioaddr + IntrStatus);
dev->name, np->intr_status,
readl(ioaddr + IntrMask));
- if (!np->intr_status)
+ if (!np->intr_status)
return IRQ_NONE;
prefetch(&np->rx_skbuff[np->cur_rx % RX_RING_SIZE]);
/* Abnormal error summary/uncommon events handlers. */
if (np->intr_status & IntrAbnormalSummary)
netdev_error(dev, np->intr_status);
-
+
if (np->intr_status &
(IntrRxDone | IntrRxIntr | RxStatusFIFOOver |
IntrRxErr | IntrRxOverrun)) {
netdev_rx(dev, &work_done, work_to_do);
}
-
+
*budget -= work_done;
dev->quota -= work_done;
u32 rx_mode;
if (dev->flags & IFF_PROMISC) { /* Set promiscuous. */
- /* Unconditionally log net taps. */
- printk(KERN_NOTICE "%s: Promiscuous mode enabled.\n",
- dev->name);
rx_mode = RxFilterEnable | AcceptBroadcast
| AcceptAllMulticast | AcceptAllPhys | AcceptMyPhys;
} else if ((dev->mc_count > multicast_filter_limit)
return res;
}
-static struct ethtool_ops ethtool_ops = {
+static const struct ethtool_ops ethtool_ops = {
.get_drvinfo = get_drvinfo,
.get_regs_len = get_regs_len,
.get_eeprom_len = get_eeprom_len,
* phy, even if the internal phy is used. This is necessary
* to work around a deficiency of the ethtool interface:
* It's only possible to query the settings of the active
- * port. Therefore
+ * port. Therefore
* # ethtool -s ethX port mii
* actually sends an ioctl to switch to port mii with the
* settings that are used for the current active port.
printk(version);
#endif
- return pci_module_init (&natsemi_driver);
+ return pci_register_driver(&natsemi_driver);
}
static void __exit natsemi_exit_mod (void)
git.openpandora.org / pandora-kernel.git / blobdiff