<file:Documentation/networking/net-modules.txt>. The module will be
called forcedeth.
+config FORCEDETH_NAPI
+ bool "Use Rx and Tx Polling (NAPI) (EXPERIMENTAL)"
+ depends on FORCEDETH && EXPERIMENTAL
+ help
+ NAPI is a new driver API designed to reduce CPU and interrupt load
+ when the driver is receiving lots of packets from the card. It is
+ still somewhat experimental and thus not yet enabled by default.
+
+ If your estimated Rx load is 10kpps or more, or if the card will be
+ deployed on potentially unfriendly networks (e.g. in a firewall),
+ then say Y here.
+
+ See <file:Documentation/networking/NAPI_HOWTO.txt> for more
+ information.
+
+ If in doubt, say N.
config CS89x0
tristate "CS89x0 support"
If unsure, say Y.
+config VIA_RHINE_NAPI
+ bool "Use Rx Polling (NAPI)"
+ depends on VIA_RHINE
+ help
+ NAPI is a new driver API designed to reduce CPU and interrupt load
+ when the driver is receiving lots of packets from the card.
+
+ If your estimated Rx load is 10kpps or more, or if the card will be
+ deployed on potentially unfriendly networks (e.g. in a firewall),
+ then say Y here.
+
+ See <file:Documentation/networking/NAPI_HOWTO.txt> for more
+ information.
+
config LAN_SAA9730
bool "Philips SAA9730 Ethernet support (EXPERIMENTAL)"
depends on NET_PCI && EXPERIMENTAL && MIPS
bool "NAPI Support"
depends on GIANFAR
+config UCC_GETH
+ tristate "Freescale QE UCC GETH"
+ depends on QUICC_ENGINE && UCC_FAST
+ help
+ This driver supports the Gigabit Ethernet mode of QE UCC.
+ QE can be found on MPC836x CPUs.
+
+config UGETH_NAPI
+ bool "NAPI Support"
+ depends on UCC_GETH
+
+config UGETH_MAGIC_PACKET
+ bool "Magic Packet detection support"
+ depends on UCC_GETH
+
+config UGETH_FILTERING
+ bool "Mac address filtering support"
+ depends on UCC_GETH
+
+config UGETH_TX_ON_DEMOND
+ bool "Transmit on Demond support"
+ depends on UCC_GETH
+
+config UGETH_HAS_GIGA
+ bool
+ depends on UCC_GETH && MPC836x
+
config MV643XX_ETH
tristate "MV-643XX Ethernet support"
depends on MOMENCO_OCELOT_C || MOMENCO_JAGUAR_ATX || MV64360 || MOMENCO_OCELOT_3 || PPC_MULTIPLATFORM
This enables support for Port 2 of the Marvell MV643XX Gigabit
Ethernet.
+config QLA3XXX
+ tristate "QLogic QLA3XXX Network Driver Support"
+ depends on PCI
+ help
+ This driver supports QLogic ISP3XXX gigabit Ethernet cards.
+
+ To compile this driver as a module, choose M here: the module
+ will be called qla3xxx.
+
endmenu
#
you will need a newer firmware image.
You may get this image or more information, at:
- <http://www.myri.com/Myri-10G/>
+ <http://www.myri.com/scs/download-Myri10GE.html>
To compile this driver as a module, choose M here and read
<file:Documentation/networking/net-modules.txt>. The module
config PPP
tristate "PPP (point-to-point protocol) support"
+ select SLHC
---help---
PPP (Point to Point Protocol) is a newer and better SLIP. It serves
the same purpose: sending Internet traffic over telephone (and other
config SLIP_COMPRESSED
bool "CSLIP compressed headers"
depends on SLIP
+ select SLHC
---help---
This protocol is faster than SLIP because it uses compression on the
TCP/IP headers (not on the data itself), but it has to be supported
<http://www.tldp.org/docs.html#howto>, explains how to configure
CSLIP. This won't enlarge your kernel.
+config SLHC
+ tristate
+ help
+ This option enables Van Jacobsen serial line header compression
+ routines.
+
config SLIP_SMART
bool "Keepalive and linefill"
depends on SLIP