*/
int wm831x_auxadc_read(struct wm831x *wm831x, enum wm831x_auxadc input)
{
- int ret, src;
+ int ret, src, irq_masked, timeout;
+
+ /* Are we using the interrupt? */
+ irq_masked = wm831x_reg_read(wm831x, WM831X_INTERRUPT_STATUS_1_MASK);
+ irq_masked &= WM831X_AUXADC_DATA_EINT;
mutex_lock(&wm831x->auxadc_lock);
goto out;
}
+ /* Clear any notification from a very late arriving interrupt */
+ try_wait_for_completion(&wm831x->auxadc_done);
+
ret = wm831x_set_bits(wm831x, WM831X_AUXADC_CONTROL,
WM831X_AUX_CVT_ENA, WM831X_AUX_CVT_ENA);
if (ret < 0) {
goto disable;
}
- /* If an interrupt arrived late clean up after it */
- try_wait_for_completion(&wm831x->auxadc_done);
-
- /* Ignore the result to allow us to soldier on without IRQ hookup */
- wait_for_completion_timeout(&wm831x->auxadc_done, msecs_to_jiffies(5));
-
- ret = wm831x_reg_read(wm831x, WM831X_AUXADC_CONTROL);
- if (ret < 0) {
- dev_err(wm831x->dev, "AUXADC status read failed: %d\n", ret);
- goto disable;
- }
-
- if (ret & WM831X_AUX_CVT_ENA) {
- dev_err(wm831x->dev, "Timed out reading AUXADC\n");
- ret = -EBUSY;
- goto disable;
+ if (irq_masked) {
+ /* If we're not using interrupts then poll the
+ * interrupt status register */
+ timeout = 5;
+ while (timeout) {
+ msleep(1);
+
+ ret = wm831x_reg_read(wm831x,
+ WM831X_INTERRUPT_STATUS_1);
+ if (ret < 0) {
+ dev_err(wm831x->dev,
+ "ISR 1 read failed: %d\n", ret);
+ goto disable;
+ }
+
+ /* Did it complete? */
+ if (ret & WM831X_AUXADC_DATA_EINT) {
+ wm831x_reg_write(wm831x,
+ WM831X_INTERRUPT_STATUS_1,
+ WM831X_AUXADC_DATA_EINT);
+ break;
+ } else {
+ dev_err(wm831x->dev,
+ "AUXADC conversion timeout\n");
+ ret = -EBUSY;
+ goto disable;
+ }
+ }
+ } else {
+ /* If we are using interrupts then wait for the
+ * interrupt to complete. Use an extremely long
+ * timeout to handle situations with heavy load where
+ * the notification of the interrupt may be delayed by
+ * threaded IRQ handling. */
+ if (!wait_for_completion_timeout(&wm831x->auxadc_done,
+ msecs_to_jiffies(500))) {
+ dev_err(wm831x->dev, "Timed out waiting for AUXADC\n");
+ ret = -EBUSY;
+ goto disable;
+ }
}
ret = wm831x_reg_read(wm831x, WM831X_AUXADC_DATA);
case WM8310:
parent = WM8310;
wm831x->num_gpio = 16;
+ wm831x->charger_irq_wake = 1;
if (rev > 0) {
wm831x->has_gpio_ena = 1;
wm831x->has_cs_sts = 1;
case WM8311:
parent = WM8311;
wm831x->num_gpio = 16;
+ wm831x->charger_irq_wake = 1;
if (rev > 0) {
wm831x->has_gpio_ena = 1;
wm831x->has_cs_sts = 1;
case WM8312:
parent = WM8312;
wm831x->num_gpio = 16;
+ wm831x->charger_irq_wake = 1;
if (rev > 0) {
wm831x->has_gpio_ena = 1;
wm831x->has_cs_sts = 1;
kfree(wm831x);
}
+static int wm831x_device_suspend(struct wm831x *wm831x)
+{
+ int reg, mask;
+
+ /* If the charger IRQs are a wake source then make sure we ack
+ * them even if they're not actively being used (eg, no power
+ * driver or no IRQ line wired up) then acknowledge the
+ * interrupts otherwise suspend won't last very long.
+ */
+ if (wm831x->charger_irq_wake) {
+ reg = wm831x_reg_read(wm831x, WM831X_INTERRUPT_STATUS_2_MASK);
+
+ mask = WM831X_CHG_BATT_HOT_EINT |
+ WM831X_CHG_BATT_COLD_EINT |
+ WM831X_CHG_BATT_FAIL_EINT |
+ WM831X_CHG_OV_EINT | WM831X_CHG_END_EINT |
+ WM831X_CHG_TO_EINT | WM831X_CHG_MODE_EINT |
+ WM831X_CHG_START_EINT;
+
+ /* If any of the interrupts are masked read the statuses */
+ if (reg & mask)
+ reg = wm831x_reg_read(wm831x,
+ WM831X_INTERRUPT_STATUS_2);
+
+ if (reg & mask) {
+ dev_info(wm831x->dev,
+ "Acknowledging masked charger IRQs: %x\n",
+ reg & mask);
+ wm831x_reg_write(wm831x, WM831X_INTERRUPT_STATUS_2,
+ reg & mask);
+ }
+ }
+
+ return 0;
+}
+
static int wm831x_i2c_read_device(struct wm831x *wm831x, unsigned short reg,
int bytes, void *dest)
{
return 0;
}
+static int wm831x_i2c_suspend(struct i2c_client *i2c, pm_message_t mesg)
+{
+ struct wm831x *wm831x = i2c_get_clientdata(i2c);
+
+ return wm831x_device_suspend(wm831x);
+}
+
static const struct i2c_device_id wm831x_i2c_id[] = {
{ "wm8310", WM8310 },
{ "wm8311", WM8311 },
},
.probe = wm831x_i2c_probe,
.remove = wm831x_i2c_remove,
+ .suspend = wm831x_i2c_suspend,
.id_table = wm831x_i2c_id,
};