*/
/*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/
-#include <linux/config.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/errno.h>
mpt_interrupt(int irq, void *bus_id, struct pt_regs *r)
{
MPT_ADAPTER *ioc = bus_id;
- u32 pa;
+ u32 pa = CHIPREG_READ32_dmasync(&ioc->chip->ReplyFifo);
+
+ if (pa == 0xFFFFFFFF)
+ return IRQ_NONE;
/*
* Drain the reply FIFO!
*/
- while (1) {
- pa = CHIPREG_READ32_dmasync(&ioc->chip->ReplyFifo);
- if (pa == 0xFFFFFFFF)
- return IRQ_HANDLED;
- else if (pa & MPI_ADDRESS_REPLY_A_BIT)
+ do {
+ if (pa & MPI_ADDRESS_REPLY_A_BIT)
mpt_reply(ioc, pa);
else
mpt_turbo_reply(ioc, pa);
- }
+ pa = CHIPREG_READ32_dmasync(&ioc->chip->ReplyFifo);
+ } while (pa != 0xFFFFFFFF);
return IRQ_HANDLED;
}
*/
if (pEvReply->MsgFlags & MPI_MSGFLAGS_CONTINUATION_REPLY) {
freereq = 0;
- devtverboseprintk((MYIOC_s_WARN_FMT "EVENT_NOTIFICATION reply %p does not return Request frame\n",
- ioc->name, pEvReply));
} else {
devtverboseprintk((MYIOC_s_WARN_FMT "EVENT_NOTIFICATION reply %p returns Request frame\n",
ioc->name, pEvReply));
mpt_device_driver_register(struct mpt_pci_driver * dd_cbfunc, int cb_idx)
{
MPT_ADAPTER *ioc;
+ const struct pci_device_id *id;
- if (cb_idx < 1 || cb_idx >= MPT_MAX_PROTOCOL_DRIVERS) {
+ if (cb_idx < 1 || cb_idx >= MPT_MAX_PROTOCOL_DRIVERS)
return -EINVAL;
- }
MptDeviceDriverHandlers[cb_idx] = dd_cbfunc;
/* call per pci device probe entry point */
list_for_each_entry(ioc, &ioc_list, list) {
- if(dd_cbfunc->probe) {
- dd_cbfunc->probe(ioc->pcidev,
- ioc->pcidev->driver->id_table);
- }
+ id = ioc->pcidev->driver ?
+ ioc->pcidev->driver->id_table : NULL;
+ if (dd_cbfunc->probe)
+ dd_cbfunc->probe(ioc->pcidev, id);
}
return 0;
dinitprintk((MYIOC_s_INFO_FMT
"host_page_buffer @ %p, dma @ %x, sz=%d bytes\n",
- ioc->name,
- ioc->HostPageBuffer,
- ioc->HostPageBuffer_dma,
+ ioc->name, ioc->HostPageBuffer,
+ (u32)ioc->HostPageBuffer_dma,
host_page_buffer_sz));
ioc->alloc_total += host_page_buffer_sz;
ioc->HostPageBuffer_sz = host_page_buffer_sz;
port = psize = 0;
for (ii=0; ii < DEVICE_COUNT_RESOURCE; ii++) {
if (pci_resource_flags(pdev, ii) & PCI_BASE_ADDRESS_SPACE_IO) {
+ if (psize)
+ continue;
/* Get I/O space! */
port = pci_resource_start(pdev, ii);
psize = pci_resource_len(pdev,ii);
} else {
+ if (msize)
+ continue;
/* Get memmap */
mem_phys = pci_resource_start(pdev, ii);
msize = pci_resource_len(pdev,ii);
- break;
}
}
ioc->mem_size = msize;
- if (ii == DEVICE_COUNT_RESOURCE) {
- printk(KERN_ERR MYNAM ": ERROR - MPT adapter has no memory regions defined!\n");
- kfree(ioc);
- return -EINVAL;
- }
-
- dinitprintk((KERN_INFO MYNAM ": MPT adapter @ %lx, msize=%dd bytes\n", mem_phys, msize));
- dinitprintk((KERN_INFO MYNAM ": (port i/o @ %lx, psize=%dd bytes)\n", port, psize));
-
mem = NULL;
/* Get logical ptr for PciMem0 space */
/*mem = ioremap(mem_phys, msize);*/
- mem = ioremap(mem_phys, 0x100);
+ mem = ioremap(mem_phys, msize);
if (mem == NULL) {
printk(KERN_ERR MYNAM ": ERROR - Unable to map adapter memory!\n");
kfree(ioc);
ioc->bus_type = SAS;
ioc->errata_flag_1064 = 1;
}
- else if (pdev->device == MPI_MANUFACTPAGE_DEVID_SAS1066) {
- ioc->prod_name = "LSISAS1066";
- ioc->bus_type = SAS;
- ioc->errata_flag_1064 = 1;
- }
else if (pdev->device == MPI_MANUFACTPAGE_DEVID_SAS1068) {
ioc->prod_name = "LSISAS1068";
ioc->bus_type = SAS;
ioc->prod_name = "LSISAS1064E";
ioc->bus_type = SAS;
}
- else if (pdev->device == MPI_MANUFACTPAGE_DEVID_SAS1066E) {
- ioc->prod_name = "LSISAS1066E";
- ioc->bus_type = SAS;
- }
else if (pdev->device == MPI_MANUFACTPAGE_DEVID_SAS1068E) {
ioc->prod_name = "LSISAS1068E";
ioc->bus_type = SAS;
}
+ else if (pdev->device == MPI_MANUFACTPAGE_DEVID_SAS1078) {
+ ioc->prod_name = "LSISAS1078";
+ ioc->bus_type = SAS;
+ }
if (ioc->errata_flag_1064)
pci_disable_io_access(pdev);
printk(KERN_WARNING MYNAM
": WARNING - %s did not initialize properly! (%d)\n",
ioc->name, r);
+
list_del(&ioc->list);
if (ioc->alt_ioc)
ioc->alt_ioc->alt_ioc = NULL;
printk(MYIOC_s_INFO_FMT "PCI-MSI enabled\n",
ioc->name);
rc = request_irq(ioc->pcidev->irq, mpt_interrupt,
- SA_SHIRQ, ioc->name, ioc);
+ IRQF_SHARED, ioc->name, ioc);
if (rc < 0) {
printk(MYIOC_s_ERR_FMT "Unable to allocate "
"interrupt %d!\n", ioc->name,
* chips (mpt_adapter_disable,
* mpt_diag_reset)
*/
- ioc->cached_fw = NULL;
ddlprintk((MYIOC_s_INFO_FMT ": mpt_upload: alt_%s has cached_fw=%p \n",
ioc->name, ioc->alt_ioc->name, ioc->alt_ioc->cached_fw));
+ ioc->alt_ioc->cached_fw = NULL;
}
} else {
printk(KERN_WARNING MYNAM ": firmware upload failure!\n");
/* FIXME? Examine results here? */
}
-out:
+ out:
if ((ret != 0) && irq_allocated) {
free_irq(ioc->pci_irq, ioc);
if (mpt_msi_enable)
dinitprintk((MYIOC_s_INFO_FMT "INFO - Wait IOC_OPERATIONAL state (cnt=%d)\n",
ioc->name, count));
+ ioc->aen_event_read_flag=0;
return r;
}
if (ioc->alt_ioc && ioc->alt_ioc->cached_fw) {
ioc->cached_fw = ioc->alt_ioc->cached_fw; /* use alt_ioc's memory */
ioc->cached_fw_dma = ioc->alt_ioc->cached_fw_dma;
+ ioc->alloc_total += size;
+ ioc->alt_ioc->alloc_total -= size;
} else {
if ( (ioc->cached_fw = pci_alloc_consistent(ioc->pcidev, size, &ioc->cached_fw_dma) ) )
ioc->alloc_total += size;
static int
mpt_diag_reset(MPT_ADAPTER *ioc, int ignore, int sleepFlag)
{
+ MPT_ADAPTER *iocp=NULL;
u32 diag0val;
u32 doorbell;
int hard_reset_done = 0;
u32 diag1val = 0;
#endif
+ if (ioc->pcidev->device == MPI_MANUFACTPAGE_DEVID_SAS1078) {
+ drsprintk((MYIOC_s_WARN_FMT "%s: Doorbell=%p; 1078 reset "
+ "address=%p\n", ioc->name, __FUNCTION__,
+ &ioc->chip->Doorbell, &ioc->chip->Reset_1078));
+ CHIPREG_WRITE32(&ioc->chip->Reset_1078, 0x07);
+ if (sleepFlag == CAN_SLEEP)
+ msleep(1);
+ else
+ mdelay(1);
+
+ for (count = 0; count < 60; count ++) {
+ doorbell = CHIPREG_READ32(&ioc->chip->Doorbell);
+ doorbell &= MPI_IOC_STATE_MASK;
+
+ drsprintk((MYIOC_s_INFO_FMT
+ "looking for READY STATE: doorbell=%x"
+ " count=%d\n",
+ ioc->name, doorbell, count));
+ if (doorbell == MPI_IOC_STATE_READY) {
+ return 0;
+ }
+
+ /* wait 1 sec */
+ if (sleepFlag == CAN_SLEEP)
+ msleep(1000);
+ else
+ mdelay(1000);
+ }
+ return -1;
+ }
+
/* Clear any existing interrupts */
CHIPREG_WRITE32(&ioc->chip->IntStatus, 0);
/* FIXME? Examine results here? */
}
- if (ioc->cached_fw) {
+ if (ioc->cached_fw)
+ iocp = ioc;
+ else if (ioc->alt_ioc && ioc->alt_ioc->cached_fw)
+ iocp = ioc->alt_ioc;
+ if (iocp) {
/* If the DownloadBoot operation fails, the
* IOC will be left unusable. This is a fatal error
* case. _diag_reset will return < 0
*/
for (count = 0; count < 30; count ++) {
- diag0val = CHIPREG_READ32(&ioc->chip->Diagnostic);
+ diag0val = CHIPREG_READ32(&iocp->chip->Diagnostic);
if (!(diag0val & MPI_DIAG_RESET_ADAPTER)) {
break;
}
+ dprintk((MYIOC_s_INFO_FMT "cached_fw: diag0val=%x count=%d\n",
+ iocp->name, diag0val, count));
/* wait 1 sec */
if (sleepFlag == CAN_SLEEP) {
msleep (1000);
}
}
if ((count = mpt_downloadboot(ioc,
- (MpiFwHeader_t *)ioc->cached_fw, sleepFlag)) < 0) {
+ (MpiFwHeader_t *)iocp->cached_fw, sleepFlag)) < 0) {
printk(KERN_WARNING MYNAM
": firmware downloadboot failure (%d)!\n", count);
}
if (sleepFlag == CAN_SLEEP) {
while (--cntdn) {
+ msleep (1);
intstat = CHIPREG_READ32(&ioc->chip->IntStatus);
if (! (intstat & MPI_HIS_IOP_DOORBELL_STATUS))
break;
- msleep (1);
count++;
}
} else {
while (--cntdn) {
+ mdelay (1);
intstat = CHIPREG_READ32(&ioc->chip->IntStatus);
if (! (intstat & MPI_HIS_IOP_DOORBELL_STATUS))
break;
- mdelay (1);
count++;
}
}
pIoc4 = pci_alloc_consistent(ioc->pcidev, iocpage4sz, &ioc4_dma);
if (!pIoc4)
return;
+ ioc->alloc_total += iocpage4sz;
} else {
ioc4_dma = ioc->spi_data.IocPg4_dma;
iocpage4sz = ioc->spi_data.IocPg4Sz;
} else {
pci_free_consistent(ioc->pcidev, iocpage4sz, pIoc4, ioc4_dma);
ioc->spi_data.pIocPg4 = NULL;
+ ioc->alloc_total -= iocpage4sz;
}
}
EventAck_t *pAck;
if ((pAck = (EventAck_t *) mpt_get_msg_frame(mpt_base_index, ioc)) == NULL) {
- printk(MYIOC_s_WARN_FMT "Unable to allocate event ACK "
- "request frame for Event=%x EventContext=%x EventData=%x!\n",
- ioc->name, evnp->Event, le32_to_cpu(evnp->EventContext),
- le32_to_cpu(evnp->Data[0]));
+ dfailprintk((MYIOC_s_WARN_FMT "%s, no msg frames!!\n",
+ ioc->name,__FUNCTION__));
return -1;
}
- memset(pAck, 0, sizeof(*pAck));
- dprintk((MYIOC_s_INFO_FMT "Sending EventAck\n", ioc->name));
+ devtverboseprintk((MYIOC_s_INFO_FMT "Sending EventAck\n", ioc->name));
pAck->Function = MPI_FUNCTION_EVENT_ACK;
pAck->ChainOffset = 0;
+ pAck->Reserved[0] = pAck->Reserved[1] = 0;
pAck->MsgFlags = 0;
+ pAck->Reserved1[0] = pAck->Reserved1[1] = pAck->Reserved1[2] = 0;
pAck->Event = evnp->Event;
pAck->EventContext = evnp->EventContext;
/* The SCSI driver needs to adjust timeouts on all current
* commands prior to the diagnostic reset being issued.
- * Prevents timeouts occuring during a diagnostic reset...very bad.
+ * Prevents timeouts occurring during a diagnostic reset...very bad.
* For all other protocol drivers, this is a no-op.
*/
{
break;
case MPI_EVENT_EVENT_CHANGE:
if (evData0)
- ds = "Events(ON) Change";
+ ds = "Events ON";
else
- ds = "Events(OFF) Change";
+ ds = "Events OFF";
break;
case MPI_EVENT_INTEGRATED_RAID:
{
break;
case MPI_EVENT_SAS_DEV_STAT_RC_NO_PERSIST_ADDED:
snprintf(evStr, EVENT_DESCR_STR_SZ,
- "SAS Device Status Change: No Persistancy "
- "Added: id=%d", id);
+ "SAS Device Status Change: No Persistancy: id=%d", id);
+ break;
+ case MPI_EVENT_SAS_DEV_STAT_RC_INTERNAL_DEVICE_RESET:
+ snprintf(evStr, EVENT_DESCR_STR_SZ,
+ "SAS Device Status Change: Internal Device Reset : id=%d", id);
+ break;
+ case MPI_EVENT_SAS_DEV_STAT_RC_TASK_ABORT_INTERNAL:
+ snprintf(evStr, EVENT_DESCR_STR_SZ,
+ "SAS Device Status Change: Internal Task Abort : id=%d", id);
+ break;
+ case MPI_EVENT_SAS_DEV_STAT_RC_ABORT_TASK_SET_INTERNAL:
+ snprintf(evStr, EVENT_DESCR_STR_SZ,
+ "SAS Device Status Change: Internal Abort Task Set : id=%d", id);
+ break;
+ case MPI_EVENT_SAS_DEV_STAT_RC_CLEAR_TASK_SET_INTERNAL:
+ snprintf(evStr, EVENT_DESCR_STR_SZ,
+ "SAS Device Status Change: Internal Clear Task Set : id=%d", id);
+ break;
+ case MPI_EVENT_SAS_DEV_STAT_RC_QUERY_TASK_INTERNAL:
+ snprintf(evStr, EVENT_DESCR_STR_SZ,
+ "SAS Device Status Change: Internal Query Task : id=%d", id);
break;
default:
snprintf(evStr, EVENT_DESCR_STR_SZ,
* @ioc: Pointer to MPT_ADAPTER structure
* @log_info: U32 LogInfo reply word from the IOC
*
- * Refer to lsi/fc_log.h.
+ * Refer to lsi/mpi_log_fc.h.
*/
static void
mpt_fc_log_info(MPT_ADAPTER *ioc, u32 log_info)
"Invalid SAS Address", /* 01h */
NULL, /* 02h */
"Invalid Page", /* 03h */
- NULL, /* 04h */
- "Task Terminated" /* 05h */
+ "Diag Message Error", /* 04h */
+ "Task Terminated", /* 05h */
+ "Enclosure Management", /* 06h */
+ "Target Mode" /* 07h */
};
static char *pl_code_str[] = {
NULL, /* 00h */
"IO Executed", /* 14h */
"Persistant Reservation Out Not Affiliation Owner", /* 15h */
"Open Transmit DMA Abort", /* 16h */
- NULL, /* 17h */
+ "IO Device Missing Delay Retry", /* 17h */
NULL, /* 18h */
NULL, /* 19h */
NULL, /* 1Ah */
mpt_sp_ioc_info(MPT_ADAPTER *ioc, u32 ioc_status, MPT_FRAME_HDR *mf)
{
u32 status = ioc_status & MPI_IOCSTATUS_MASK;
- char *desc = "";
+ char *desc = NULL;
switch (status) {
case MPI_IOCSTATUS_INVALID_FUNCTION: /* 0x0001 */
desc = "Others";
break;
}
- if (desc != "")
+ if (desc != NULL)
printk(MYIOC_s_INFO_FMT "IOCStatus(0x%04x): %s\n", ioc->name, status, desc);
}
EXPORT_SYMBOL(mpt_free_fw_memory);
EXPORT_SYMBOL(mptbase_sas_persist_operation);
-
/*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/
/*
* fusion_init - Fusion MPT base driver initialization routine.
git.openpandora.org / pandora-kernel.git / blobdiff