module_param_array(card, int, NULL, 0444);
MODULE_PARM_DESC(card, "card type");
-#define MT9V011_VERSION 0x8243
-
/* Bitmask marking allocated devices from 0 to EM28XX_MAXBOARDS */
static unsigned long em28xx_devused;
{ -1, -1, -1, -1},
};
+/* Pinnacle Hybrid Pro eb1a:2881 */
+static struct em28xx_reg_seq pinnacle_hybrid_pro_analog[] = {
+ {EM28XX_R08_GPIO, 0xfd, ~EM_GPIO_4, 10},
+ { -1, -1, -1, -1},
+};
+
+static struct em28xx_reg_seq pinnacle_hybrid_pro_digital[] = {
+ {EM28XX_R08_GPIO, 0x6e, ~EM_GPIO_4, 10},
+ {EM2880_R04_GPO, 0x04, 0xff, 100},/* zl10353 reset */
+ {EM2880_R04_GPO, 0x0c, 0xff, 1},
+ { -1, -1, -1, -1},
+};
+
+
/* Callback for the most boards */
static struct em28xx_reg_seq default_tuner_gpio[] = {
{EM28XX_R08_GPIO, EM_GPIO_4, EM_GPIO_4, 10},
*/
struct em28xx_board em28xx_boards[] = {
[EM2750_BOARD_UNKNOWN] = {
- .name = "Unknown EM2750/EM2751 webcam grabber",
- .xclk = EM28XX_XCLK_FREQUENCY_48MHZ,
- .tuner_type = TUNER_ABSENT, /* This is a webcam */
+ .name = "EM2710/EM2750/EM2751 webcam grabber",
+ .xclk = EM28XX_XCLK_FREQUENCY_20MHZ,
+ .tuner_type = TUNER_ABSENT,
+ .is_webcam = 1,
.input = { {
.type = EM28XX_VMUX_COMPOSITE1,
.vmux = 0,
.amux = EM28XX_AMUX_VIDEO,
+ .gpio = silvercrest_reg_seq,
} },
},
[EM2800_BOARD_UNKNOWN] = {
[EM2820_BOARD_UNKNOWN] = {
.name = "Unknown EM2750/28xx video grabber",
.tuner_type = TUNER_ABSENT,
+ .is_webcam = 1, /* To enable sensor probe */
},
[EM2750_BOARD_DLCW_130] = {
/* Beijing Huaqi Information Digital Technology Co., Ltd */
.name = "Huaqi DLCW-130",
.valid = EM28XX_BOARD_NOT_VALIDATED,
.xclk = EM28XX_XCLK_FREQUENCY_48MHZ,
- .tuner_type = TUNER_ABSENT, /* This is a webcam */
+ .tuner_type = TUNER_ABSENT,
+ .is_webcam = 1,
.input = { {
.type = EM28XX_VMUX_COMPOSITE1,
.vmux = 0,
[EM2820_BOARD_VIDEOLOGY_20K14XUSB] = {
.name = "Videology 20K14XUSB USB2.0",
.valid = EM28XX_BOARD_NOT_VALIDATED,
- .tuner_type = TUNER_ABSENT, /* This is a webcam */
+ .tuner_type = TUNER_ABSENT,
+ .is_webcam = 1,
.input = { {
.type = EM28XX_VMUX_COMPOSITE1,
.vmux = 0,
[EM2820_BOARD_SILVERCREST_WEBCAM] = {
.name = "Silvercrest Webcam 1.3mpix",
.tuner_type = TUNER_ABSENT,
- .is_27xx = 1,
- .decoder = EM28XX_MT9V011,
+ .is_webcam = 1,
.input = { {
.type = EM28XX_VMUX_COMPOSITE1,
.vmux = 0,
/* Beijing Huaqi Information Digital Technology Co., Ltd */
.name = "NetGMBH Cam",
.valid = EM28XX_BOARD_NOT_VALIDATED,
- .tuner_type = TUNER_ABSENT, /* This is a webcam */
+ .tuner_type = TUNER_ABSENT,
+ .is_webcam = 1,
.input = { {
.type = EM28XX_VMUX_COMPOSITE1,
.vmux = 0,
},
[EM2861_BOARD_PLEXTOR_PX_TV100U] = {
.name = "Plextor ConvertX PX-TV100U",
- .valid = EM28XX_BOARD_NOT_VALIDATED,
.tuner_type = TUNER_TNF_5335MF,
+ .xclk = EM28XX_XCLK_I2S_MSB_TIMING |
+ EM28XX_XCLK_FREQUENCY_12MHZ,
.tda9887_conf = TDA9887_PRESENT,
.decoder = EM28XX_TVP5150,
+ .has_msp34xx = 1,
.input = { {
.type = EM28XX_VMUX_TELEVISION,
.vmux = TVP5150_COMPOSITE0,
.amux = EM28XX_AMUX_LINE_IN,
+ .gpio = pinnacle_hybrid_pro_analog,
}, {
.type = EM28XX_VMUX_COMPOSITE1,
.vmux = TVP5150_COMPOSITE1,
.amux = EM28XX_AMUX_LINE_IN,
+ .gpio = pinnacle_hybrid_pro_analog,
}, {
.type = EM28XX_VMUX_SVIDEO,
.vmux = TVP5150_SVIDEO,
.amux = EM28XX_AMUX_LINE_IN,
+ .gpio = pinnacle_hybrid_pro_analog,
} },
},
},
[EM2881_BOARD_PINNACLE_HYBRID_PRO] = {
.name = "Pinnacle Hybrid Pro",
- .valid = EM28XX_BOARD_NOT_VALIDATED,
.tuner_type = TUNER_XC2028,
.tuner_gpio = default_tuner_gpio,
.decoder = EM28XX_TVP5150,
+ .has_dvb = 1,
+ .dvb_gpio = pinnacle_hybrid_pro_digital,
.input = { {
.type = EM28XX_VMUX_TELEVISION,
.vmux = TVP5150_COMPOSITE0,
.amux = EM28XX_AMUX_VIDEO,
- .gpio = default_analog,
+ .gpio = pinnacle_hybrid_pro_analog,
}, {
.type = EM28XX_VMUX_COMPOSITE1,
.vmux = TVP5150_COMPOSITE1,
.amux = EM28XX_AMUX_LINE_IN,
- .gpio = default_analog,
+ .gpio = pinnacle_hybrid_pro_analog,
}, {
.type = EM28XX_VMUX_SVIDEO,
.vmux = TVP5150_SVIDEO,
.amux = EM28XX_AMUX_LINE_IN,
- .gpio = default_analog,
+ .gpio = pinnacle_hybrid_pro_analog,
} },
},
[EM2882_BOARD_PINNACLE_HYBRID_PRO] = {
.driver_info = EM2750_BOARD_UNKNOWN },
{ USB_DEVICE(0xeb1a, 0x2800),
.driver_info = EM2800_BOARD_UNKNOWN },
+ { USB_DEVICE(0xeb1a, 0x2710),
+ .driver_info = EM2820_BOARD_UNKNOWN },
{ USB_DEVICE(0xeb1a, 0x2820),
.driver_info = EM2820_BOARD_UNKNOWN },
{ USB_DEVICE(0xeb1a, 0x2821),
{0x966a0441, EM2880_BOARD_KWORLD_DVB_310U, TUNER_XC2028},
{0x9567eb1a, EM2880_BOARD_EMPIRE_DUAL_TV, TUNER_XC2028},
{0xcee44a99, EM2882_BOARD_EVGA_INDTUBE, TUNER_XC2028},
+ {0xb8846b20, EM2881_BOARD_PINNACLE_HYBRID_PRO, TUNER_XC2028},
};
/* I2C devicelist hash table for devices with generic USB IDs */
EM28XX_I2C_FREQ_100_KHZ;
}
+/* FIXME: Should be replaced by a proper mt9m001 driver */
+static int em28xx_initialize_mt9m001(struct em28xx *dev)
+{
+ int i;
+ unsigned char regs[][3] = {
+ { 0x0d, 0x00, 0x01, },
+ { 0x0d, 0x00, 0x00, },
+ { 0x04, 0x05, 0x00, }, /* hres = 1280 */
+ { 0x03, 0x04, 0x00, }, /* vres = 1024 */
+ { 0x20, 0x11, 0x00, },
+ { 0x06, 0x00, 0x10, },
+ { 0x2b, 0x00, 0x24, },
+ { 0x2e, 0x00, 0x24, },
+ { 0x35, 0x00, 0x24, },
+ { 0x2d, 0x00, 0x20, },
+ { 0x2c, 0x00, 0x20, },
+ { 0x09, 0x0a, 0xd4, },
+ { 0x35, 0x00, 0x57, },
+ };
+
+ for (i = 0; i < ARRAY_SIZE(regs); i++)
+ i2c_master_send(&dev->i2c_client, ®s[i][0], 3);
+
+ return 0;
+}
+
/* HINT method: webcam I2C chips
*
* This method work for webcams with Micron sensors
__be16 version_be;
u16 version;
- if (dev->model != EM2820_BOARD_UNKNOWN)
- return 0;
-
+ /* Micron sensor detection */
dev->i2c_client.addr = 0xba >> 1;
cmd = 0;
i2c_master_send(&dev->i2c_client, &cmd, 1);
return -EINVAL;
version = be16_to_cpu(version_be);
-
switch (version) {
- case MT9V011_VERSION:
+ case 0x8232: /* mt9v011 640x480 1.3 Mpix sensor */
+ case 0x8243: /* mt9v011 rev B 640x480 1.3 Mpix sensor */
dev->model = EM2820_BOARD_SILVERCREST_WEBCAM;
+ em28xx_set_model(dev);
+
sensor_name = "mt9v011";
+ dev->em28xx_sensor = EM28XX_MT9V011;
+ dev->sensor_xres = 640;
+ dev->sensor_yres = 480;
+ /*
+ * FIXME: mt9v011 uses I2S speed as xtal clk - at least with
+ * the Silvercrest cam I have here for testing - for higher
+ * resolutions, a high clock cause horizontal artifacts, so we
+ * need to use a lower xclk frequency.
+ * Yet, it would be possible to adjust xclk depending on the
+ * desired resolution, since this affects directly the
+ * frame rate.
+ */
+ dev->board.xclk = EM28XX_XCLK_FREQUENCY_4_3MHZ;
+ dev->sensor_xtal = 4300000;
+
+ /* probably means GRGB 16 bit bayer */
+ dev->vinmode = 0x0d;
+ dev->vinctl = 0x00;
+
+ break;
+ case 0x8431:
+ dev->model = EM2750_BOARD_UNKNOWN;
+ em28xx_set_model(dev);
+
+ sensor_name = "mt9m001";
+ dev->em28xx_sensor = EM28XX_MT9M001;
+ em28xx_initialize_mt9m001(dev);
+ dev->sensor_xres = 1280;
+ dev->sensor_yres = 1024;
+
+ /* probably means BGGR 16 bit bayer */
+ dev->vinmode = 0x0c;
+ dev->vinctl = 0x00;
+
break;
default:
- printk("Unknown Sensor 0x%04x\n", be16_to_cpu(version));
+ printk("Unknown Micron Sensor 0x%04x\n", be16_to_cpu(version));
return -EINVAL;
}
- em28xx_errdev("Sensor is %s, assuming that webcam is %s\n",
+ /* Setup webcam defaults */
+ em28xx_pre_card_setup(dev);
+
+ em28xx_errdev("Sensor is %s, using model %s entry.\n",
sensor_name, em28xx_boards[dev->model].name);
return 0;
*/
void em28xx_pre_card_setup(struct em28xx *dev)
{
- int rc;
-
- em28xx_set_model(dev);
-
- em28xx_info("Identified as %s (card=%d)\n",
- dev->board.name, dev->model);
-
- /* Set the default GPO/GPIO for legacy devices */
- dev->reg_gpo_num = EM2880_R04_GPO;
- dev->reg_gpio_num = EM28XX_R08_GPIO;
-
- dev->wait_after_write = 5;
-
- /* Based on the Chip ID, set the device configuration */
- rc = em28xx_read_reg(dev, EM28XX_R0A_CHIPID);
- if (rc > 0) {
- dev->chip_id = rc;
-
- switch (dev->chip_id) {
- case CHIP_ID_EM2750:
- em28xx_info("chip ID is em2750\n");
- break;
- case CHIP_ID_EM2820:
- if (dev->board.is_27xx)
- em28xx_info("chip is em2710\n");
- else
- em28xx_info("chip ID is em2820\n");
- break;
- case CHIP_ID_EM2840:
- em28xx_info("chip ID is em2840\n");
- break;
- case CHIP_ID_EM2860:
- em28xx_info("chip ID is em2860\n");
- break;
- case CHIP_ID_EM2870:
- em28xx_info("chip ID is em2870\n");
- dev->wait_after_write = 0;
- break;
- case CHIP_ID_EM2874:
- em28xx_info("chip ID is em2874\n");
- dev->reg_gpio_num = EM2874_R80_GPIO;
- dev->wait_after_write = 0;
- break;
- case CHIP_ID_EM2883:
- em28xx_info("chip ID is em2882/em2883\n");
- dev->wait_after_write = 0;
- break;
- default:
- em28xx_info("em28xx chip ID = %d\n", dev->chip_id);
- }
- }
-
- /* Prepopulate cached GPO register content */
- rc = em28xx_read_reg(dev, dev->reg_gpo_num);
- if (rc >= 0)
- dev->reg_gpo = rc;
-
/* Set the initial XCLK and I2C clock values based on the board
definition */
em28xx_write_reg(dev, EM28XX_R0F_XCLK, dev->board.xclk & 0x7f);
/* request some modules */
switch (dev->model) {
case EM2861_BOARD_PLEXTOR_PX_TV100U:
- /* FIXME guess */
- /* Turn on analog audio output */
- em28xx_write_reg(dev, EM28XX_R08_GPIO, 0xfd);
+ /* Sets the msp34xx I2S speed */
+ dev->i2s_speed = 2048000;
break;
case EM2861_BOARD_KWORLD_PVRTV_300U:
case EM2880_BOARD_KWORLD_DVB_305U:
ctl->demod = XC3028_FE_ZARLINK456;
break;
case EM2880_BOARD_TERRATEC_HYBRID_XS:
+ case EM2881_BOARD_PINNACLE_HYBRID_PRO:
ctl->demod = XC3028_FE_ZARLINK456;
break;
case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900_R2:
void em28xx_card_setup(struct em28xx *dev)
{
- em28xx_set_model(dev);
+ /*
+ * If the device can be a webcam, seek for a sensor.
+ * If sensor is not found, then it isn't a webcam.
+ */
+ if (dev->board.is_webcam) {
+ if (em28xx_hint_sensor(dev) < 0)
+ dev->board.is_webcam = 0;
+ else
+ dev->progressive = 1;
+ } else
+ em28xx_set_model(dev);
+
+ em28xx_info("Identified as %s (card=%d)\n",
+ dev->board.name, dev->model);
dev->tuner_type = em28xx_boards[dev->model].tuner_type;
if (em28xx_boards[dev->model].tuner_addr)
em28xx_set_mode() in em28xx_pre_card_setup() was a no-op,
so make the call now so the analog GPIOs are set properly
before probing the i2c bus. */
+ em28xx_gpio_set(dev, dev->board.tuner_gpio);
em28xx_set_mode(dev, EM28XX_ANALOG_MODE);
break;
- case EM2820_BOARD_SILVERCREST_WEBCAM:
- /* FIXME: need to document the registers bellow */
- em28xx_write_reg(dev, 0x0d, 0x42);
- em28xx_write_reg(dev, 0x13, 0x08);
}
if (dev->board.has_snapshot_button)
v4l2_i2c_new_probed_subdev(&dev->v4l2_dev, &dev->i2c_adap,
"tvp5150", "tvp5150", tvp5150_addrs);
- if (dev->board.decoder == EM28XX_MT9V011)
- v4l2_i2c_new_probed_subdev(&dev->v4l2_dev, &dev->i2c_adap,
- "mt9v011", "mt9v011", mt9v011_addrs);
+ if (dev->em28xx_sensor == EM28XX_MT9V011) {
+ struct v4l2_subdev *sd;
+
+ sd = v4l2_i2c_new_probed_subdev(&dev->v4l2_dev,
+ &dev->i2c_adap, "mt9v011", "mt9v011", mt9v011_addrs);
+ v4l2_subdev_call(sd, core, s_config, 0, &dev->sensor_xtal);
+ }
+
if (dev->board.adecoder == EM28XX_TVAUDIO)
v4l2_i2c_new_subdev(&dev->v4l2_dev, &dev->i2c_adap,
int minor)
{
struct em28xx *dev = *devhandle;
- int retval = -ENOMEM;
+ int retval;
int errCode;
dev->udev = udev;
dev->em28xx_read_reg_req = em28xx_read_reg_req;
dev->board.is_em2800 = em28xx_boards[dev->model].is_em2800;
+ em28xx_set_model(dev);
+
+ /* Set the default GPO/GPIO for legacy devices */
+ dev->reg_gpo_num = EM2880_R04_GPO;
+ dev->reg_gpio_num = EM28XX_R08_GPIO;
+
+ dev->wait_after_write = 5;
+
+ /* Based on the Chip ID, set the device configuration */
+ retval = em28xx_read_reg(dev, EM28XX_R0A_CHIPID);
+ if (retval > 0) {
+ dev->chip_id = retval;
+
+ switch (dev->chip_id) {
+ case CHIP_ID_EM2710:
+ em28xx_info("chip ID is em2710\n");
+ break;
+ case CHIP_ID_EM2750:
+ em28xx_info("chip ID is em2750\n");
+ break;
+ case CHIP_ID_EM2820:
+ em28xx_info("chip ID is em2820 (or em2710)\n");
+ break;
+ case CHIP_ID_EM2840:
+ em28xx_info("chip ID is em2840\n");
+ break;
+ case CHIP_ID_EM2860:
+ em28xx_info("chip ID is em2860\n");
+ break;
+ case CHIP_ID_EM2870:
+ em28xx_info("chip ID is em2870\n");
+ dev->wait_after_write = 0;
+ break;
+ case CHIP_ID_EM2874:
+ em28xx_info("chip ID is em2874\n");
+ dev->reg_gpio_num = EM2874_R80_GPIO;
+ dev->wait_after_write = 0;
+ break;
+ case CHIP_ID_EM2883:
+ em28xx_info("chip ID is em2882/em2883\n");
+ dev->wait_after_write = 0;
+ break;
+ default:
+ em28xx_info("em28xx chip ID = %d\n", dev->chip_id);
+ }
+ }
+
+ /* Prepopulate cached GPO register content */
+ retval = em28xx_read_reg(dev, dev->reg_gpo_num);
+ if (retval >= 0)
+ dev->reg_gpo = retval;
+
em28xx_pre_card_setup(dev);
if (!dev->board.is_em2800) {
return errCode;
}
- em28xx_hint_sensor(dev);
+ /*
+ * Default format, used for tvp5150 or saa711x output formats
+ */
+ dev->vinmode = 0x10;
+ dev->vinctl = 0x11;
/* Do board specific init and eeprom reading */
em28xx_card_setup(dev);
git.openpandora.org / pandora-kernel.git / blobdiff