* Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
* Portions Copyright (C) 2003 Red Hat Inc
+ * Portions Copyright (C) 2005-2006 MontaVista Software, Inc.
*
* Thanks to HighPoint Technologies for their assistance, and hardware.
* Special Thanks to Jon Burchmore in SanDiego for the deep pockets, his
* development and support.
*
*
- * Highpoint have their own driver (source except for the raid part)
- * available from http://www.highpoint-tech.com/hpt3xx-opensource-v131.tgz
- * This may be useful to anyone wanting to work on the mainstream hpt IDE.
+ * HighPoint has its own drivers (open source except for the RAID part)
+ * available from http://www.highpoint-tech.com/BIOS%20+%20Driver/.
+ * This may be useful to anyone wanting to work on this driver, however do not
+ * trust them too much since the code tends to become less and less meaningful
+ * as the time passes... :-/
*
* Note that final HPT370 support was done by force extraction of GPL.
*
* keeping me sane.
* Alan Cox <alan@redhat.com>
*
+ * - fix the clock turnaround code: it was writing to the wrong ports when
+ * called for the secondary channel, caching the current clock mode per-
+ * channel caused the cached register value to get out of sync with the
+ * actual one, the channels weren't serialized, the turnaround shouldn't
+ * be done on 66 MHz PCI bus
+ * - avoid calibrating PLL twice as the second time results in a wrong PCI
+ * frequency and thus in the wrong timings for the secondary channel
+ * - disable UltraATA/133 for HPT372 by default (50 MHz DPLL clock do not
+ * allow for this speed anyway)
+ * - add support for HPT302N and HPT371N clocking (the same as for HPT372N)
+ * - HPT371/N are single channel chips, so avoid touching the primary channel
+ * which exists only virtually (there's no pins for it)
+ * - fix/remove bad/unused timing tables and use one set of tables for the whole
+ * HPT37x chip family; save space by introducing the separate transfer mode
+ * table in which the mode lookup is done
+ * - use f_CNT value saved by the HighPoint BIOS as reading it directly gives
+ * the wrong PCI frequency since DPLL has already been calibrated by BIOS
+ * - fix the hotswap code: it caused RESET- to glitch when tristating the bus,
+ * and for HPT36x the obsolete HDIO_TRISTATE_HWIF handler was called instead
+ * - pass to init_chipset() handlers a copy of the IDE PCI device structure as
+ * they tamper with its fields
+ * <source@mvista.com>
+ *
*/
/* various tuning parameters */
#define HPT_RESET_STATE_ENGINE
-#undef HPT_DELAY_INTERRUPT
-#undef HPT_SERIALIZE_IO
+#undef HPT_DELAY_INTERRUPT
+#define HPT_SERIALIZE_IO 0
static const char *quirk_drives[] = {
"QUANTUM FIREBALLlct08 08",
NULL
};
-struct chipset_bus_clock_list_entry {
- u8 xfer_speed;
- unsigned int chipset_settings;
+static u8 xfer_speeds[] = {
+ XFER_UDMA_6,
+ XFER_UDMA_5,
+ XFER_UDMA_4,
+ XFER_UDMA_3,
+ XFER_UDMA_2,
+ XFER_UDMA_1,
+ XFER_UDMA_0,
+
+ XFER_MW_DMA_2,
+ XFER_MW_DMA_1,
+ XFER_MW_DMA_0,
+
+ XFER_PIO_4,
+ XFER_PIO_3,
+ XFER_PIO_2,
+ XFER_PIO_1,
+ XFER_PIO_0
};
-/* key for bus clock timings
- * bit
- * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
- * DMA. cycles = value + 1
- * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW
- * DMA. cycles = value + 1
- * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file
- * register access.
- * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file
- * register access.
- * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer.
- * during task file register access.
- * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA
- * xfer.
- * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task
- * register access.
- * 28 UDMA enable
- * 29 DMA enable
- * 30 PIO_MST enable. if set, the chip is in bus master mode during
- * PIO.
- * 31 FIFO enable.
+/* Key for bus clock timings
+ * 36x 37x
+ * bits bits
+ * 0:3 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
+ * cycles = value + 1
+ * 4:7 4:8 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
+ * cycles = value + 1
+ * 8:11 9:12 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
+ * register access.
+ * 12:15 13:17 cmd_low_time. Active time of DIOW_/DIOR_ during task file
+ * register access.
+ * 16:18 18:20 udma_cycle_time. Clock cycles for UDMA xfer.
+ * - 21 CLK frequency: 0=ATA clock, 1=dual ATA clock.
+ * 19:21 22:24 pre_high_time. Time to initialize the 1st cycle for PIO and
+ * MW DMA xfer.
+ * 22:24 25:27 cmd_pre_high_time. Time to initialize the 1st PIO cycle for
+ * task file register access.
+ * 28 28 UDMA enable.
+ * 29 29 DMA enable.
+ * 30 30 PIO MST enable. If set, the chip is in bus master mode during
+ * PIO xfer.
+ * 31 31 FIFO enable.
*/
-static struct chipset_bus_clock_list_entry forty_base_hpt366[] = {
- { XFER_UDMA_4, 0x900fd943 },
- { XFER_UDMA_3, 0x900ad943 },
- { XFER_UDMA_2, 0x900bd943 },
- { XFER_UDMA_1, 0x9008d943 },
- { XFER_UDMA_0, 0x9008d943 },
-
- { XFER_MW_DMA_2, 0xa008d943 },
- { XFER_MW_DMA_1, 0xa010d955 },
- { XFER_MW_DMA_0, 0xa010d9fc },
-
- { XFER_PIO_4, 0xc008d963 },
- { XFER_PIO_3, 0xc010d974 },
- { XFER_PIO_2, 0xc010d997 },
- { XFER_PIO_1, 0xc010d9c7 },
- { XFER_PIO_0, 0xc018d9d9 },
- { 0, 0x0120d9d9 }
-};
-
-static struct chipset_bus_clock_list_entry thirty_three_base_hpt366[] = {
- { XFER_UDMA_4, 0x90c9a731 },
- { XFER_UDMA_3, 0x90cfa731 },
- { XFER_UDMA_2, 0x90caa731 },
- { XFER_UDMA_1, 0x90cba731 },
- { XFER_UDMA_0, 0x90c8a731 },
-
- { XFER_MW_DMA_2, 0xa0c8a731 },
- { XFER_MW_DMA_1, 0xa0c8a732 }, /* 0xa0c8a733 */
- { XFER_MW_DMA_0, 0xa0c8a797 },
-
- { XFER_PIO_4, 0xc0c8a731 },
- { XFER_PIO_3, 0xc0c8a742 },
- { XFER_PIO_2, 0xc0d0a753 },
- { XFER_PIO_1, 0xc0d0a7a3 }, /* 0xc0d0a793 */
- { XFER_PIO_0, 0xc0d0a7aa }, /* 0xc0d0a7a7 */
- { 0, 0x0120a7a7 }
-};
-
-static struct chipset_bus_clock_list_entry twenty_five_base_hpt366[] = {
- { XFER_UDMA_4, 0x90c98521 },
- { XFER_UDMA_3, 0x90cf8521 },
- { XFER_UDMA_2, 0x90cf8521 },
- { XFER_UDMA_1, 0x90cb8521 },
- { XFER_UDMA_0, 0x90cb8521 },
-
- { XFER_MW_DMA_2, 0xa0ca8521 },
- { XFER_MW_DMA_1, 0xa0ca8532 },
- { XFER_MW_DMA_0, 0xa0ca8575 },
-
- { XFER_PIO_4, 0xc0ca8521 },
- { XFER_PIO_3, 0xc0ca8532 },
- { XFER_PIO_2, 0xc0ca8542 },
- { XFER_PIO_1, 0xc0d08572 },
- { XFER_PIO_0, 0xc0d08585 },
- { 0, 0x01208585 }
-};
-
-/* from highpoint documentation. these are old values */
-static struct chipset_bus_clock_list_entry thirty_three_base_hpt370[] = {
-/* { XFER_UDMA_5, 0x1A85F442, 0x16454e31 }, */
- { XFER_UDMA_5, 0x16454e31 },
- { XFER_UDMA_4, 0x16454e31 },
- { XFER_UDMA_3, 0x166d4e31 },
- { XFER_UDMA_2, 0x16494e31 },
- { XFER_UDMA_1, 0x164d4e31 },
- { XFER_UDMA_0, 0x16514e31 },
-
- { XFER_MW_DMA_2, 0x26514e21 },
- { XFER_MW_DMA_1, 0x26514e33 },
- { XFER_MW_DMA_0, 0x26514e97 },
-
- { XFER_PIO_4, 0x06514e21 },
- { XFER_PIO_3, 0x06514e22 },
- { XFER_PIO_2, 0x06514e33 },
- { XFER_PIO_1, 0x06914e43 },
- { XFER_PIO_0, 0x06914e57 },
- { 0, 0x06514e57 }
-};
-
-static struct chipset_bus_clock_list_entry sixty_six_base_hpt370[] = {
- { XFER_UDMA_5, 0x14846231 },
- { XFER_UDMA_4, 0x14886231 },
- { XFER_UDMA_3, 0x148c6231 },
- { XFER_UDMA_2, 0x148c6231 },
- { XFER_UDMA_1, 0x14906231 },
- { XFER_UDMA_0, 0x14986231 },
-
- { XFER_MW_DMA_2, 0x26514e21 },
- { XFER_MW_DMA_1, 0x26514e33 },
- { XFER_MW_DMA_0, 0x26514e97 },
-
- { XFER_PIO_4, 0x06514e21 },
- { XFER_PIO_3, 0x06514e22 },
- { XFER_PIO_2, 0x06514e33 },
- { XFER_PIO_1, 0x06914e43 },
- { XFER_PIO_0, 0x06914e57 },
- { 0, 0x06514e57 }
-};
-
-/* these are the current (4 sep 2001) timings from highpoint */
-static struct chipset_bus_clock_list_entry thirty_three_base_hpt370a[] = {
- { XFER_UDMA_5, 0x12446231 },
- { XFER_UDMA_4, 0x12446231 },
- { XFER_UDMA_3, 0x126c6231 },
- { XFER_UDMA_2, 0x12486231 },
- { XFER_UDMA_1, 0x124c6233 },
- { XFER_UDMA_0, 0x12506297 },
-
- { XFER_MW_DMA_2, 0x22406c31 },
- { XFER_MW_DMA_1, 0x22406c33 },
- { XFER_MW_DMA_0, 0x22406c97 },
-
- { XFER_PIO_4, 0x06414e31 },
- { XFER_PIO_3, 0x06414e42 },
- { XFER_PIO_2, 0x06414e53 },
- { XFER_PIO_1, 0x06814e93 },
- { XFER_PIO_0, 0x06814ea7 },
- { 0, 0x06814ea7 }
-};
-
-/* 2x 33MHz timings */
-static struct chipset_bus_clock_list_entry sixty_six_base_hpt370a[] = {
- { XFER_UDMA_5, 0x1488e673 },
- { XFER_UDMA_4, 0x1488e673 },
- { XFER_UDMA_3, 0x1498e673 },
- { XFER_UDMA_2, 0x1490e673 },
- { XFER_UDMA_1, 0x1498e677 },
- { XFER_UDMA_0, 0x14a0e73f },
-
- { XFER_MW_DMA_2, 0x2480fa73 },
- { XFER_MW_DMA_1, 0x2480fa77 },
- { XFER_MW_DMA_0, 0x2480fb3f },
-
- { XFER_PIO_4, 0x0c82be73 },
- { XFER_PIO_3, 0x0c82be95 },
- { XFER_PIO_2, 0x0c82beb7 },
- { XFER_PIO_1, 0x0d02bf37 },
- { XFER_PIO_0, 0x0d02bf5f },
- { 0, 0x0d02bf5f }
-};
-static struct chipset_bus_clock_list_entry fifty_base_hpt370a[] = {
- { XFER_UDMA_5, 0x12848242 },
- { XFER_UDMA_4, 0x12ac8242 },
- { XFER_UDMA_3, 0x128c8242 },
- { XFER_UDMA_2, 0x120c8242 },
- { XFER_UDMA_1, 0x12148254 },
- { XFER_UDMA_0, 0x121882ea },
-
- { XFER_MW_DMA_2, 0x22808242 },
- { XFER_MW_DMA_1, 0x22808254 },
- { XFER_MW_DMA_0, 0x228082ea },
-
- { XFER_PIO_4, 0x0a81f442 },
- { XFER_PIO_3, 0x0a81f443 },
- { XFER_PIO_2, 0x0a81f454 },
- { XFER_PIO_1, 0x0ac1f465 },
- { XFER_PIO_0, 0x0ac1f48a },
- { 0, 0x0ac1f48a }
+static u32 forty_base_hpt36x[] = {
+ /* XFER_UDMA_6 */ 0x900fd943,
+ /* XFER_UDMA_5 */ 0x900fd943,
+ /* XFER_UDMA_4 */ 0x900fd943,
+ /* XFER_UDMA_3 */ 0x900ad943,
+ /* XFER_UDMA_2 */ 0x900bd943,
+ /* XFER_UDMA_1 */ 0x9008d943,
+ /* XFER_UDMA_0 */ 0x9008d943,
+
+ /* XFER_MW_DMA_2 */ 0xa008d943,
+ /* XFER_MW_DMA_1 */ 0xa010d955,
+ /* XFER_MW_DMA_0 */ 0xa010d9fc,
+
+ /* XFER_PIO_4 */ 0xc008d963,
+ /* XFER_PIO_3 */ 0xc010d974,
+ /* XFER_PIO_2 */ 0xc010d997,
+ /* XFER_PIO_1 */ 0xc010d9c7,
+ /* XFER_PIO_0 */ 0xc018d9d9
};
-static struct chipset_bus_clock_list_entry thirty_three_base_hpt372[] = {
- { XFER_UDMA_6, 0x1c81dc62 },
- { XFER_UDMA_5, 0x1c6ddc62 },
- { XFER_UDMA_4, 0x1c8ddc62 },
- { XFER_UDMA_3, 0x1c8edc62 }, /* checkme */
- { XFER_UDMA_2, 0x1c91dc62 },
- { XFER_UDMA_1, 0x1c9adc62 }, /* checkme */
- { XFER_UDMA_0, 0x1c82dc62 }, /* checkme */
-
- { XFER_MW_DMA_2, 0x2c829262 },
- { XFER_MW_DMA_1, 0x2c829266 }, /* checkme */
- { XFER_MW_DMA_0, 0x2c82922e }, /* checkme */
-
- { XFER_PIO_4, 0x0c829c62 },
- { XFER_PIO_3, 0x0c829c84 },
- { XFER_PIO_2, 0x0c829ca6 },
- { XFER_PIO_1, 0x0d029d26 },
- { XFER_PIO_0, 0x0d029d5e },
- { 0, 0x0d029d5e }
+static u32 thirty_three_base_hpt36x[] = {
+ /* XFER_UDMA_6 */ 0x90c9a731,
+ /* XFER_UDMA_5 */ 0x90c9a731,
+ /* XFER_UDMA_4 */ 0x90c9a731,
+ /* XFER_UDMA_3 */ 0x90cfa731,
+ /* XFER_UDMA_2 */ 0x90caa731,
+ /* XFER_UDMA_1 */ 0x90cba731,
+ /* XFER_UDMA_0 */ 0x90c8a731,
+
+ /* XFER_MW_DMA_2 */ 0xa0c8a731,
+ /* XFER_MW_DMA_1 */ 0xa0c8a732, /* 0xa0c8a733 */
+ /* XFER_MW_DMA_0 */ 0xa0c8a797,
+
+ /* XFER_PIO_4 */ 0xc0c8a731,
+ /* XFER_PIO_3 */ 0xc0c8a742,
+ /* XFER_PIO_2 */ 0xc0d0a753,
+ /* XFER_PIO_1 */ 0xc0d0a7a3, /* 0xc0d0a793 */
+ /* XFER_PIO_0 */ 0xc0d0a7aa /* 0xc0d0a7a7 */
};
-static struct chipset_bus_clock_list_entry fifty_base_hpt372[] = {
- { XFER_UDMA_5, 0x12848242 },
- { XFER_UDMA_4, 0x12ac8242 },
- { XFER_UDMA_3, 0x128c8242 },
- { XFER_UDMA_2, 0x120c8242 },
- { XFER_UDMA_1, 0x12148254 },
- { XFER_UDMA_0, 0x121882ea },
-
- { XFER_MW_DMA_2, 0x22808242 },
- { XFER_MW_DMA_1, 0x22808254 },
- { XFER_MW_DMA_0, 0x228082ea },
-
- { XFER_PIO_4, 0x0a81f442 },
- { XFER_PIO_3, 0x0a81f443 },
- { XFER_PIO_2, 0x0a81f454 },
- { XFER_PIO_1, 0x0ac1f465 },
- { XFER_PIO_0, 0x0ac1f48a },
- { 0, 0x0a81f443 }
+static u32 twenty_five_base_hpt36x[] = {
+ /* XFER_UDMA_6 */ 0x90c98521,
+ /* XFER_UDMA_5 */ 0x90c98521,
+ /* XFER_UDMA_4 */ 0x90c98521,
+ /* XFER_UDMA_3 */ 0x90cf8521,
+ /* XFER_UDMA_2 */ 0x90cf8521,
+ /* XFER_UDMA_1 */ 0x90cb8521,
+ /* XFER_UDMA_0 */ 0x90cb8521,
+
+ /* XFER_MW_DMA_2 */ 0xa0ca8521,
+ /* XFER_MW_DMA_1 */ 0xa0ca8532,
+ /* XFER_MW_DMA_0 */ 0xa0ca8575,
+
+ /* XFER_PIO_4 */ 0xc0ca8521,
+ /* XFER_PIO_3 */ 0xc0ca8532,
+ /* XFER_PIO_2 */ 0xc0ca8542,
+ /* XFER_PIO_1 */ 0xc0d08572,
+ /* XFER_PIO_0 */ 0xc0d08585
};
-static struct chipset_bus_clock_list_entry sixty_six_base_hpt372[] = {
- { XFER_UDMA_6, 0x1c869c62 },
- { XFER_UDMA_5, 0x1cae9c62 },
- { XFER_UDMA_4, 0x1c8a9c62 },
- { XFER_UDMA_3, 0x1c8e9c62 },
- { XFER_UDMA_2, 0x1c929c62 },
- { XFER_UDMA_1, 0x1c9a9c62 },
- { XFER_UDMA_0, 0x1c829c62 },
-
- { XFER_MW_DMA_2, 0x2c829c62 },
- { XFER_MW_DMA_1, 0x2c829c66 },
- { XFER_MW_DMA_0, 0x2c829d2e },
-
- { XFER_PIO_4, 0x0c829c62 },
- { XFER_PIO_3, 0x0c829c84 },
- { XFER_PIO_2, 0x0c829ca6 },
- { XFER_PIO_1, 0x0d029d26 },
- { XFER_PIO_0, 0x0d029d5e },
- { 0, 0x0d029d26 }
+static u32 thirty_three_base_hpt37x[] = {
+ /* XFER_UDMA_6 */ 0x12446231, /* 0x12646231 ?? */
+ /* XFER_UDMA_5 */ 0x12446231,
+ /* XFER_UDMA_4 */ 0x12446231,
+ /* XFER_UDMA_3 */ 0x126c6231,
+ /* XFER_UDMA_2 */ 0x12486231,
+ /* XFER_UDMA_1 */ 0x124c6233,
+ /* XFER_UDMA_0 */ 0x12506297,
+
+ /* XFER_MW_DMA_2 */ 0x22406c31,
+ /* XFER_MW_DMA_1 */ 0x22406c33,
+ /* XFER_MW_DMA_0 */ 0x22406c97,
+
+ /* XFER_PIO_4 */ 0x06414e31,
+ /* XFER_PIO_3 */ 0x06414e42,
+ /* XFER_PIO_2 */ 0x06414e53,
+ /* XFER_PIO_1 */ 0x06814e93,
+ /* XFER_PIO_0 */ 0x06814ea7
};
-static struct chipset_bus_clock_list_entry thirty_three_base_hpt374[] = {
- { XFER_UDMA_6, 0x12808242 },
- { XFER_UDMA_5, 0x12848242 },
- { XFER_UDMA_4, 0x12ac8242 },
- { XFER_UDMA_3, 0x128c8242 },
- { XFER_UDMA_2, 0x120c8242 },
- { XFER_UDMA_1, 0x12148254 },
- { XFER_UDMA_0, 0x121882ea },
-
- { XFER_MW_DMA_2, 0x22808242 },
- { XFER_MW_DMA_1, 0x22808254 },
- { XFER_MW_DMA_0, 0x228082ea },
-
- { XFER_PIO_4, 0x0a81f442 },
- { XFER_PIO_3, 0x0a81f443 },
- { XFER_PIO_2, 0x0a81f454 },
- { XFER_PIO_1, 0x0ac1f465 },
- { XFER_PIO_0, 0x0ac1f48a },
- { 0, 0x06814e93 }
+static u32 fifty_base_hpt37x[] = {
+ /* XFER_UDMA_6 */ 0x12848242,
+ /* XFER_UDMA_5 */ 0x12848242,
+ /* XFER_UDMA_4 */ 0x12ac8242,
+ /* XFER_UDMA_3 */ 0x128c8242,
+ /* XFER_UDMA_2 */ 0x120c8242,
+ /* XFER_UDMA_1 */ 0x12148254,
+ /* XFER_UDMA_0 */ 0x121882ea,
+
+ /* XFER_MW_DMA_2 */ 0x22808242,
+ /* XFER_MW_DMA_1 */ 0x22808254,
+ /* XFER_MW_DMA_0 */ 0x228082ea,
+
+ /* XFER_PIO_4 */ 0x0a81f442,
+ /* XFER_PIO_3 */ 0x0a81f443,
+ /* XFER_PIO_2 */ 0x0a81f454,
+ /* XFER_PIO_1 */ 0x0ac1f465,
+ /* XFER_PIO_0 */ 0x0ac1f48a
};
-/* FIXME: 50MHz timings for HPT374 */
-
-#if 0
-static struct chipset_bus_clock_list_entry sixty_six_base_hpt374[] = {
- { XFER_UDMA_6, 0x12406231 }, /* checkme */
- { XFER_UDMA_5, 0x12446231 }, /* 0x14846231 */
- { XFER_UDMA_4, 0x16814ea7 }, /* 0x14886231 */
- { XFER_UDMA_3, 0x16814ea7 }, /* 0x148c6231 */
- { XFER_UDMA_2, 0x16814ea7 }, /* 0x148c6231 */
- { XFER_UDMA_1, 0x16814ea7 }, /* 0x14906231 */
- { XFER_UDMA_0, 0x16814ea7 }, /* 0x14986231 */
- { XFER_MW_DMA_2, 0x16814ea7 }, /* 0x26514e21 */
- { XFER_MW_DMA_1, 0x16814ea7 }, /* 0x26514e97 */
- { XFER_MW_DMA_0, 0x16814ea7 }, /* 0x26514e97 */
- { XFER_PIO_4, 0x06814ea7 }, /* 0x06514e21 */
- { XFER_PIO_3, 0x06814ea7 }, /* 0x06514e22 */
- { XFER_PIO_2, 0x06814ea7 }, /* 0x06514e33 */
- { XFER_PIO_1, 0x06814ea7 }, /* 0x06914e43 */
- { XFER_PIO_0, 0x06814ea7 }, /* 0x06914e57 */
- { 0, 0x06814ea7 }
+static u32 sixty_six_base_hpt37x[] = {
+ /* XFER_UDMA_6 */ 0x1c869c62,
+ /* XFER_UDMA_5 */ 0x1cae9c62, /* 0x1c8a9c62 */
+ /* XFER_UDMA_4 */ 0x1c8a9c62,
+ /* XFER_UDMA_3 */ 0x1c8e9c62,
+ /* XFER_UDMA_2 */ 0x1c929c62,
+ /* XFER_UDMA_1 */ 0x1c9a9c62,
+ /* XFER_UDMA_0 */ 0x1c829c62,
+
+ /* XFER_MW_DMA_2 */ 0x2c829c62,
+ /* XFER_MW_DMA_1 */ 0x2c829c66,
+ /* XFER_MW_DMA_0 */ 0x2c829d2e,
+
+ /* XFER_PIO_4 */ 0x0c829c62,
+ /* XFER_PIO_3 */ 0x0c829c84,
+ /* XFER_PIO_2 */ 0x0c829ca6,
+ /* XFER_PIO_1 */ 0x0d029d26,
+ /* XFER_PIO_0 */ 0x0d029d5e
};
-#endif
#define HPT366_DEBUG_DRIVE_INFO 0
#define HPT374_ALLOW_ATA133_6 0
#define HPT371_ALLOW_ATA133_6 0
#define HPT302_ALLOW_ATA133_6 0
-#define HPT372_ALLOW_ATA133_6 1
+#define HPT372_ALLOW_ATA133_6 0
#define HPT370_ALLOW_ATA100_5 1
#define HPT366_ALLOW_ATA66_4 1
#define HPT366_ALLOW_ATA66_3 1
int revision; /* Chipset revision */
int flags; /* Chipset properties */
#define PLL_MODE 1
-#define IS_372N 2
+#define IS_3xxN 2
+#define PCI_66MHZ 4
/* Speed table */
- struct chipset_bus_clock_list_entry *speed;
+ u32 *speed;
};
/*
return 0;
}
-static unsigned int pci_bus_clock_list (u8 speed, struct chipset_bus_clock_list_entry * chipset_table)
+static u32 pci_bus_clock_list(u8 speed, u32 *chipset_table)
{
- for ( ; chipset_table->xfer_speed ; chipset_table++)
- if (chipset_table->xfer_speed == speed)
- return chipset_table->chipset_settings;
- return chipset_table->chipset_settings;
+ int i;
+
+ /*
+ * Lookup the transfer mode table to get the index into
+ * the timing table.
+ *
+ * NOTE: For XFER_PIO_SLOW, PIO mode 0 timings will be used.
+ */
+ for (i = 0; i < ARRAY_SIZE(xfer_speeds) - 1; i++)
+ if (xfer_speeds[i] == speed)
+ break;
+ return chipset_table[i];
}
static int hpt36x_tune_chipset(ide_drive_t *drive, u8 xferspeed)
}
/**
- * hpt372n_set_clock - perform clock switching dance
- * @drive: Drive to switch
- * @mode: Switching mode (0x21 for write, 0x23 otherwise)
+ * hpt3xxn_set_clock - perform clock switching dance
+ * @hwif: hwif to switch
+ * @mode: clocking mode (0x21 for write, 0x23 otherwise)
*
- * Switch the DPLL clock on the HPT372N devices. This is a
- * right mess.
+ * Switch the DPLL clock on the HPT3xxN devices. This is a right mess.
+ * NOTE: avoid touching the disabled primary channel on HPT371N -- it
+ * doesn't physically exist anyway...
*/
-
-static void hpt372n_set_clock(ide_drive_t *drive, int mode)
+
+static void hpt3xxn_set_clock(ide_hwif_t *hwif, u8 mode)
{
- ide_hwif_t *hwif = HWIF(drive);
-
- /* FIXME: should we check for DMA active and BUG() */
+ u8 mcr1, scr2 = hwif->INB(hwif->dma_master + 0x7b);
+
+ if ((scr2 & 0x7f) == mode)
+ return;
+
+ /* MISC. control register 1 has the channel enable bit... */
+ mcr1 = hwif->INB(hwif->dma_master + 0x70);
+
/* Tristate the bus */
- outb(0x80, hwif->dma_base+0x73);
- outb(0x80, hwif->dma_base+0x77);
-
+ if (mcr1 & 0x04)
+ hwif->OUTB(0x80, hwif->dma_master + 0x73);
+ hwif->OUTB(0x80, hwif->dma_master + 0x77);
+
/* Switch clock and reset channels */
- outb(mode, hwif->dma_base+0x7B);
- outb(0xC0, hwif->dma_base+0x79);
-
+ hwif->OUTB(mode, hwif->dma_master + 0x7b);
+ hwif->OUTB(0xc0, hwif->dma_master + 0x79);
+
/* Reset state machines */
- outb(0x37, hwif->dma_base+0x70);
- outb(0x37, hwif->dma_base+0x74);
-
+ if (mcr1 & 0x04)
+ hwif->OUTB(0x37, hwif->dma_master + 0x70);
+ hwif->OUTB(0x37, hwif->dma_master + 0x74);
+
/* Complete reset */
- outb(0x00, hwif->dma_base+0x79);
-
+ hwif->OUTB(0x00, hwif->dma_master + 0x79);
+
/* Reconnect channels to bus */
- outb(0x00, hwif->dma_base+0x73);
- outb(0x00, hwif->dma_base+0x77);
+ if (mcr1 & 0x04)
+ hwif->OUTB(0x00, hwif->dma_master + 0x73);
+ hwif->OUTB(0x00, hwif->dma_master + 0x77);
}
/**
- * hpt372n_rw_disk - prepare for I/O
+ * hpt3xxn_rw_disk - prepare for I/O
* @drive: drive for command
* @rq: block request structure
*
- * This is called when a disk I/O is issued to the 372N.
+ * This is called when a disk I/O is issued to HPT3xxN.
* We need it because of the clock switching.
*/
-static void hpt372n_rw_disk(ide_drive_t *drive, struct request *rq)
-{
- ide_hwif_t *hwif = drive->hwif;
- int wantclock;
-
- wantclock = rq_data_dir(rq) ? 0x23 : 0x21;
-
- if (hwif->config_data != wantclock) {
- hpt372n_set_clock(drive, wantclock);
- hwif->config_data = wantclock;
- }
-}
-
-/*
- * Since SUN Cobalt is attempting to do this operation, I should disclose
- * this has been a long time ago Thu Jul 27 16:40:57 2000 was the patch date
- * HOTSWAP ATA Infrastructure.
- */
-
-static void hpt3xx_reset (ide_drive_t *drive)
-{
-}
-
-static int hpt3xx_tristate (ide_drive_t * drive, int state)
+static void hpt3xxn_rw_disk(ide_drive_t *drive, struct request *rq)
{
ide_hwif_t *hwif = HWIF(drive);
- struct pci_dev *dev = hwif->pci_dev;
- u8 reg59h = 0, reset = (hwif->channel) ? 0x80 : 0x40;
- u8 regXXh = 0, state_reg= (hwif->channel) ? 0x57 : 0x53;
-
- pci_read_config_byte(dev, 0x59, ®59h);
- pci_read_config_byte(dev, state_reg, ®XXh);
+ u8 wantclock = rq_data_dir(rq) ? 0x23 : 0x21;
- if (state) {
- (void) ide_do_reset(drive);
- pci_write_config_byte(dev, state_reg, regXXh|0x80);
- pci_write_config_byte(dev, 0x59, reg59h|reset);
- } else {
- pci_write_config_byte(dev, 0x59, reg59h & ~(reset));
- pci_write_config_byte(dev, state_reg, regXXh & ~(0x80));
- (void) ide_do_reset(drive);
- }
- return 0;
+ hpt3xxn_set_clock(hwif, wantclock);
}
/*
- * set/get power state for a drive.
- * turning the power off does the following things:
- * 1) soft-reset the drive
- * 2) tri-states the ide bus
+ * Set/get power state for a drive.
*
- * when we turn things back on, we need to re-initialize things.
+ * When we turn the power back on, we need to re-initialize things.
*/
#define TRISTATE_BIT 0x8000
-static int hpt370_busproc(ide_drive_t * drive, int state)
+
+static int hpt3xx_busproc(ide_drive_t *drive, int state)
{
ide_hwif_t *hwif = drive->hwif;
struct pci_dev *dev = hwif->pci_dev;
- u8 tristate = 0, resetmask = 0, bus_reg = 0;
- u16 tri_reg;
+ u8 tristate, resetmask, bus_reg = 0;
+ u16 tri_reg = 0;
hwif->bus_state = state;
if (hwif->channel) {
/* secondary channel */
- tristate = 0x56;
- resetmask = 0x80;
+ tristate = 0x56;
+ resetmask = 0x80;
} else {
/* primary channel */
- tristate = 0x52;
+ tristate = 0x52;
resetmask = 0x40;
}
- /* grab status */
+ /* Grab the status. */
pci_read_config_word(dev, tristate, &tri_reg);
pci_read_config_byte(dev, 0x59, &bus_reg);
- /* set the state. we don't set it if we don't need to do so.
- * make sure that the drive knows that it has failed if it's off */
+ /*
+ * Set the state. We don't set it if we don't need to do so.
+ * Make sure that the drive knows that it has failed if it's off.
+ */
switch (state) {
case BUSSTATE_ON:
- hwif->drives[0].failures = 0;
- hwif->drives[1].failures = 0;
- if ((bus_reg & resetmask) == 0)
+ if (!(bus_reg & resetmask))
return 0;
- tri_reg &= ~TRISTATE_BIT;
- bus_reg &= ~resetmask;
- break;
+ hwif->drives[0].failures = hwif->drives[1].failures = 0;
+
+ pci_write_config_byte(dev, 0x59, bus_reg & ~resetmask);
+ pci_write_config_word(dev, tristate, tri_reg & ~TRISTATE_BIT);
+ return 0;
case BUSSTATE_OFF:
- hwif->drives[0].failures = hwif->drives[0].max_failures + 1;
- hwif->drives[1].failures = hwif->drives[1].max_failures + 1;
- if ((tri_reg & TRISTATE_BIT) == 0 && (bus_reg & resetmask))
+ if ((bus_reg & resetmask) && !(tri_reg & TRISTATE_BIT))
return 0;
tri_reg &= ~TRISTATE_BIT;
- bus_reg |= resetmask;
break;
case BUSSTATE_TRISTATE:
- hwif->drives[0].failures = hwif->drives[0].max_failures + 1;
- hwif->drives[1].failures = hwif->drives[1].max_failures + 1;
- if ((tri_reg & TRISTATE_BIT) && (bus_reg & resetmask))
+ if ((bus_reg & resetmask) && (tri_reg & TRISTATE_BIT))
return 0;
tri_reg |= TRISTATE_BIT;
- bus_reg |= resetmask;
break;
+ default:
+ return -EINVAL;
}
- pci_write_config_byte(dev, 0x59, bus_reg);
- pci_write_config_word(dev, tristate, tri_reg);
+ hwif->drives[0].failures = hwif->drives[0].max_failures + 1;
+ hwif->drives[1].failures = hwif->drives[1].max_failures + 1;
+
+ pci_write_config_word(dev, tristate, tri_reg);
+ pci_write_config_byte(dev, 0x59, bus_reg | resetmask);
return 0;
}
/* detect bus speed by looking at control reg timing: */
switch((reg1 >> 8) & 7) {
case 5:
- info->speed = forty_base_hpt366;
+ info->speed = forty_base_hpt36x;
break;
case 9:
- info->speed = twenty_five_base_hpt366;
+ info->speed = twenty_five_base_hpt36x;
break;
case 7:
default:
- info->speed = thirty_three_base_hpt366;
+ info->speed = thirty_three_base_hpt36x;
break;
}
}
struct hpt_info *info = ide_get_hwifdata(hwif);
struct pci_dev *dev = hwif->pci_dev;
int adjust, i;
- u16 freq;
- u32 pll;
- u8 reg5bh;
+ u16 freq = 0;
+ u32 pll, temp = 0;
+ u8 reg5bh = 0, mcr1 = 0;
/*
* default to pci clock. make sure MA15/16 are set to output
pci_write_config_byte(dev, 0x5b, 0x23);
/*
- * set up the PLL. we need to adjust it so that it's stable.
- * freq = Tpll * 192 / Tpci
+ * We'll have to read f_CNT value in order to determine
+ * the PCI clock frequency according to the following ratio:
+ *
+ * f_CNT = Fpci * 192 / Fdpll
+ *
+ * First try reading the register in which the HighPoint BIOS
+ * saves f_CNT value before reprogramming the DPLL from its
+ * default setting (which differs for the various chips).
+ * NOTE: This register is only accessible via I/O space.
*
- * Todo. For non x86 should probably check the dword is
- * set to 0xABCDExxx indicating the BIOS saved f_CNT
+ * In case the signature check fails, we'll have to resort to
+ * reading the f_CNT register itself in hopes that nobody has
+ * touched the DPLL yet...
*/
- pci_read_config_word(dev, 0x78, &freq);
- freq &= 0x1FF;
-
+ temp = inl(pci_resource_start(dev, 4) + 0x90);
+ if ((temp & 0xFFFFF000) != 0xABCDE000) {
+ printk(KERN_WARNING "HPT37X: no clock data saved by BIOS\n");
+
+ /* Calculate the average value of f_CNT */
+ for (temp = i = 0; i < 128; i++) {
+ pci_read_config_word(dev, 0x78, &freq);
+ temp += freq & 0x1ff;
+ mdelay(1);
+ }
+ freq = temp / 128;
+ } else
+ freq = temp & 0x1ff;
+
/*
- * The 372N uses different PCI clock information and has
- * some other complications
- * On PCI33 timing we must clock switch
- * On PCI66 timing we must NOT use the PCI clock
- *
- * Currently we always set up the PLL for the 372N
+ * HPT3xxN chips use different PCI clock information.
+ * Currently we always set up the PLL for them.
*/
-
- if(info->flags & IS_372N)
- {
- printk(KERN_INFO "hpt: HPT372N detected, using 372N timing.\n");
+
+ if (info->flags & IS_3xxN) {
if(freq < 0x55)
pll = F_LOW_PCI_33;
else if(freq < 0x70)
pll = F_LOW_PCI_50;
else
pll = F_LOW_PCI_66;
-
- printk(KERN_INFO "FREQ: %d PLL: %d\n", freq, pll);
-
- /* We always use the pll not the PCI clock on 372N */
+
+ printk(KERN_INFO "HPT3xxN detected, FREQ: %d, PLL: %d\n", freq, pll);
}
else
{
pll = F_LOW_PCI_66;
if (pll == F_LOW_PCI_33) {
- if (info->revision >= 8)
- info->speed = thirty_three_base_hpt374;
- else if (info->revision >= 5)
- info->speed = thirty_three_base_hpt372;
- else if (info->revision >= 4)
- info->speed = thirty_three_base_hpt370a;
- else
- info->speed = thirty_three_base_hpt370;
+ info->speed = thirty_three_base_hpt37x;
printk(KERN_DEBUG "HPT37X: using 33MHz PCI clock\n");
} else if (pll == F_LOW_PCI_40) {
/* Unsupported */
} else if (pll == F_LOW_PCI_50) {
- if (info->revision >= 8)
- info->speed = fifty_base_hpt370a;
- else if (info->revision >= 5)
- info->speed = fifty_base_hpt372;
- else if (info->revision >= 4)
- info->speed = fifty_base_hpt370a;
- else
- info->speed = fifty_base_hpt370a;
+ info->speed = fifty_base_hpt37x;
printk(KERN_DEBUG "HPT37X: using 50MHz PCI clock\n");
} else {
- if (info->revision >= 8) {
- printk(KERN_ERR "HPT37x: 66MHz timings are not supported.\n");
- }
- else if (info->revision >= 5)
- info->speed = sixty_six_base_hpt372;
- else if (info->revision >= 4)
- info->speed = sixty_six_base_hpt370a;
- else
- info->speed = sixty_six_base_hpt370;
+ info->speed = sixty_six_base_hpt37x;
printk(KERN_DEBUG "HPT37X: using 66MHz PCI clock\n");
}
}
-
+
+ if (pll == F_LOW_PCI_66)
+ info->flags |= PCI_66MHZ;
+
/*
* only try the pll if we don't have a table for the clock
* speed that we're running at. NOTE: the internal PLL will
info->flags |= PLL_MODE;
/*
- * FIXME: make this work correctly, esp with 372N as per
- * reference driver code.
- *
- * adjust PLL based upon PCI clock, enable it, and wait for
- * stabilization.
+ * Adjust the PLL based upon the PCI clock, enable it, and
+ * wait for stabilization...
*/
adjust = 0;
freq = (pll < F_LOW_PCI_50) ? 2 : 4;
pci_write_config_dword(dev, 0x5c,
pll & ~0x100);
pci_write_config_byte(dev, 0x5b, 0x21);
- if (info->revision >= 8)
- info->speed = fifty_base_hpt370a;
- else if (info->revision >= 5)
- info->speed = fifty_base_hpt372;
- else if (info->revision >= 4)
- info->speed = fifty_base_hpt370a;
- else
- info->speed = fifty_base_hpt370a;
+
+ info->speed = fifty_base_hpt37x;
printk("HPT37X: using 50MHz internal PLL\n");
goto init_hpt37X_done;
}
}
- if (!pci_get_drvdata(dev)) {
- printk("No Clock Stabilization!!!\n");
- return;
- }
pll_recal:
if (adjust & 1)
pll -= (adjust >> 1);
init_hpt37X_done:
if (!info->speed)
- printk(KERN_ERR "HPT37X%s: unknown bus timing [%d %d].\n",
- (info->flags & IS_372N)?"N":"", pll, freq);
- /* reset state engine */
- pci_write_config_byte(dev, 0x50, 0x37);
- pci_write_config_byte(dev, 0x54, 0x37);
+ printk(KERN_ERR "HPT37x%s: unknown bus timing [%d %d].\n",
+ (info->flags & IS_3xxN) ? "N" : "", pll, freq);
+ /*
+ * Reset the state engines.
+ * NOTE: avoid accidentally enabling the primary channel on HPT371N.
+ */
+ pci_read_config_byte(dev, 0x50, &mcr1);
+ if (mcr1 & 0x04)
+ pci_write_config_byte(dev, 0x50, 0x37);
+ pci_write_config_byte(dev, 0x54, 0x37);
udelay(100);
}
struct pci_dev *dev = hwif->pci_dev;
struct hpt_info *info = ide_get_hwifdata(hwif);
u8 ata66 = 0, regmask = (hwif->channel) ? 0x01 : 0x02;
+ int serialize = HPT_SERIALIZE_IO;
hwif->tuneproc = &hpt3xx_tune_drive;
hwif->speedproc = &hpt3xx_tune_chipset;
hwif->intrproc = &hpt3xx_intrproc;
hwif->maskproc = &hpt3xx_maskproc;
- if(info->flags & IS_372N)
- hwif->rw_disk = &hpt372n_rw_disk;
+ /*
+ * HPT3xxN chips have some complications:
+ *
+ * - on 33 MHz PCI we must clock switch
+ * - on 66 MHz PCI we must NOT use the PCI clock
+ */
+ if ((info->flags & (IS_3xxN | PCI_66MHZ)) == IS_3xxN) {
+ /*
+ * Clock is shared between the channels,
+ * so we'll have to serialize them... :-(
+ */
+ serialize = 1;
+ hwif->rw_disk = &hpt3xxn_rw_disk;
+ }
/*
* The HPT37x uses the CBLID pins as outputs for MA15/MA16
PCI_FUNC(hwif->pci_dev->devfn));
#endif /* DEBUG */
-#ifdef HPT_SERIALIZE_IO
- /* serialize access to this device */
- if (hwif->mate)
+ /* Serialize access to this device */
+ if (serialize && hwif->mate)
hwif->serialized = hwif->mate->serialized = 1;
-#endif
- if (info->revision >= 3) {
- u8 reg5ah = 0;
- pci_write_config_byte(dev, 0x5a, reg5ah & ~0x10);
- /*
- * set up ioctl for power status.
- * note: power affects both
- * drives on each channel
- */
- hwif->resetproc = &hpt3xx_reset;
- hwif->busproc = &hpt370_busproc;
- } else if (info->revision >= 2) {
- hwif->resetproc = &hpt3xx_reset;
- hwif->busproc = &hpt3xx_tristate;
- } else {
- hwif->resetproc = &hpt3xx_reset;
- hwif->busproc = &hpt3xx_tristate;
- }
+ /*
+ * Set up ioctl for power status.
+ * NOTE: power affects both drives on each channel.
+ */
+ hwif->busproc = &hpt3xx_busproc;
if (!hwif->dma_base) {
hwif->drives[0].autotune = 1;
return;
if(info->speed == NULL) {
- printk(KERN_WARNING "hpt: no known IDE timings, disabling DMA.\n");
+ printk(KERN_WARNING "hpt366: no known IDE timings, disabling DMA.\n");
return;
}
static void __devinit init_iops_hpt366(ide_hwif_t *hwif)
{
- struct hpt_info *info = kzalloc(sizeof(struct hpt_info), GFP_KERNEL);
- unsigned long dmabase = pci_resource_start(hwif->pci_dev, 4);
- u8 did, rid;
+ struct hpt_info *info = kzalloc(sizeof(struct hpt_info), GFP_KERNEL);
+ struct pci_dev *dev = hwif->pci_dev;
+ u16 did = dev->device;
+ u8 rid = 0;
if(info == NULL) {
printk(KERN_WARNING "hpt366: out of memory.\n");
}
ide_set_hwifdata(hwif, info);
- if(dmabase) {
- did = inb(dmabase + 0x22);
- rid = inb(dmabase + 0x28);
-
- if((did == 4 && rid == 6) || (did == 5 && rid > 1))
- info->flags |= IS_372N;
+ /* Avoid doing the same thing twice. */
+ if (hwif->channel && hwif->mate) {
+ memcpy(info, ide_get_hwifdata(hwif->mate), sizeof(struct hpt_info));
+ return;
}
- info->revision = hpt_revision(hwif->pci_dev);
+ pci_read_config_byte(dev, PCI_CLASS_REVISION, &rid);
+
+ if (( did == PCI_DEVICE_ID_TTI_HPT366 && rid == 6) ||
+ ((did == PCI_DEVICE_ID_TTI_HPT372 ||
+ did == PCI_DEVICE_ID_TTI_HPT302 ||
+ did == PCI_DEVICE_ID_TTI_HPT371) && rid > 1) ||
+ did == PCI_DEVICE_ID_TTI_HPT372N)
+ info->flags |= IS_3xxN;
+
+ info->revision = hpt_revision(dev);
if (info->revision >= 3)
hpt37x_clocking(hwif);
return ide_setup_pci_device(dev, d);
}
+static int __devinit init_setup_hpt371(struct pci_dev *dev, ide_pci_device_t *d)
+{
+ u8 mcr1 = 0;
+
+ /*
+ * HPT371 chips physically have only one channel, the secondary one,
+ * but the primary channel registers do exist! Go figure...
+ * So, we manually disable the non-existing channel here
+ * (if the BIOS hasn't done this already).
+ */
+ pci_read_config_byte(dev, 0x50, &mcr1);
+ if (mcr1 & 0x04)
+ pci_write_config_byte(dev, 0x50, (mcr1 & ~0x04));
+
+ return ide_setup_pci_device(dev, d);
+}
+
static int __devinit init_setup_hpt366(struct pci_dev *dev, ide_pci_device_t *d)
{
struct pci_dev *findev = NULL;
.bootable = OFF_BOARD,
},{ /* 3 */
.name = "HPT371",
- .init_setup = init_setup_hpt37x,
+ .init_setup = init_setup_hpt371,
.init_chipset = init_chipset_hpt366,
.init_iops = init_iops_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
.channels = 2,
.autodma = AUTODMA,
+ .enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
.bootable = OFF_BOARD,
},{ /* 4 */
.name = "HPT374",
*
* Called when the PCI registration layer (or the IDE initialization)
* finds a device matching our IDE device tables.
+ *
+ * NOTE: since we'll have to modify some fields of the ide_pci_device_t
+ * structure depending on the chip's revision, we'd better pass a local
+ * copy down the call chain...
*/
-
static int __devinit hpt366_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- ide_pci_device_t *d = &hpt366_chipsets[id->driver_data];
+ ide_pci_device_t d = hpt366_chipsets[id->driver_data];
- return d->init_setup(dev, d);
+ return d.init_setup(dev, &d);
}
static struct pci_device_id hpt366_pci_tbl[] = {
.probe = hpt366_init_one,
};
-static int hpt366_ide_init(void)
+static int __init hpt366_ide_init(void)
{
return ide_pci_register_driver(&driver);
}
git.openpandora.org / pandora-kernel.git / blobdiff