{0x409D0E11, "Smart Array 6400 EM", &SA5_access},
{0x40910E11, "Smart Array 6i", &SA5_access},
{0x3225103C, "Smart Array P600", &SA5_access},
+ {0x3223103C, "Smart Array P800", &SA5_access},
+ {0x3234103C, "Smart Array P400", &SA5_access},
{0x3235103C, "Smart Array P400i", &SA5_access},
{0x3211103C, "Smart Array E200i", &SA5_access},
{0x3212103C, "Smart Array E200", &SA5_access},
for (i = 0; i < MAX_CONFIG_WAIT; i++) {
if (!(readl(h->vaddr + SA5_DOORBELL) & CFGTBL_ChangeReq))
break;
- msleep(10);
+ usleep_range(10000, 20000);
}
}
*board_id = ((subsystem_device_id << 16) & 0xffff0000) |
subsystem_vendor_id;
- for (i = 0; i < ARRAY_SIZE(products); i++) {
+ for (i = 0; i < ARRAY_SIZE(products); i++)
if (*board_id == products[i].board_id)
return i;
- }
dev_warn(&pdev->dev, "unrecognized board ID: 0x%08x, ignoring.\n",
*board_id);
return -ENODEV;
return -ENODEV;
}
-static int __devinit cciss_wait_for_board_ready(ctlr_info_t *h)
+static int __devinit cciss_wait_for_board_state(struct pci_dev *pdev,
+ void __iomem *vaddr, int wait_for_ready)
+#define BOARD_READY 1
+#define BOARD_NOT_READY 0
{
- int i;
+ int i, iterations;
u32 scratchpad;
- for (i = 0; i < CCISS_BOARD_READY_ITERATIONS; i++) {
- scratchpad = readl(h->vaddr + SA5_SCRATCHPAD_OFFSET);
- if (scratchpad == CCISS_FIRMWARE_READY)
- return 0;
+ if (wait_for_ready)
+ iterations = CCISS_BOARD_READY_ITERATIONS;
+ else
+ iterations = CCISS_BOARD_NOT_READY_ITERATIONS;
+
+ for (i = 0; i < iterations; i++) {
+ scratchpad = readl(vaddr + SA5_SCRATCHPAD_OFFSET);
+ if (wait_for_ready) {
+ if (scratchpad == CCISS_FIRMWARE_READY)
+ return 0;
+ } else {
+ if (scratchpad != CCISS_FIRMWARE_READY)
+ return 0;
+ }
msleep(CCISS_BOARD_READY_POLL_INTERVAL_MSECS);
}
- dev_warn(&h->pdev->dev, "board not ready, timed out.\n");
+ dev_warn(&pdev->dev, "board not ready, timed out.\n");
return -ENODEV;
}
static void __devinit cciss_get_max_perf_mode_cmds(struct ctlr_info *h)
{
h->max_commands = readl(&(h->cfgtable->MaxPerformantModeCommands));
+
+ /* Limit commands in memory limited kdump scenario. */
+ if (reset_devices && h->max_commands > 32)
+ h->max_commands = 32;
+
if (h->max_commands < 16) {
dev_warn(&h->pdev->dev, "Controller reports "
"max supported commands of %d, an obvious lie. "
err = -ENOMEM;
goto err_out_free_res;
}
- err = cciss_wait_for_board_ready(h);
+ err = cciss_wait_for_board_state(h->pdev, h->vaddr, BOARD_READY);
if (err)
goto err_out_free_res;
err = cciss_find_cfgtables(h);
#define cciss_soft_reset_controller(p) cciss_message(p, 1, 0)
#define cciss_noop(p) cciss_message(p, 3, 0)
-static __devinit int cciss_reset_msi(struct pci_dev *pdev)
-{
-/* the #defines are stolen from drivers/pci/msi.h. */
-#define msi_control_reg(base) (base + PCI_MSI_FLAGS)
-#define PCI_MSIX_FLAGS_ENABLE (1 << 15)
-
- int pos;
- u16 control = 0;
-
- pos = pci_find_capability(pdev, PCI_CAP_ID_MSI);
- if (pos) {
- pci_read_config_word(pdev, msi_control_reg(pos), &control);
- if (control & PCI_MSI_FLAGS_ENABLE) {
- dev_info(&pdev->dev, "resetting MSI\n");
- pci_write_config_word(pdev, msi_control_reg(pos), control & ~PCI_MSI_FLAGS_ENABLE);
- }
- }
-
- pos = pci_find_capability(pdev, PCI_CAP_ID_MSIX);
- if (pos) {
- pci_read_config_word(pdev, msi_control_reg(pos), &control);
- if (control & PCI_MSIX_FLAGS_ENABLE) {
- dev_info(&pdev->dev, "resetting MSI-X\n");
- pci_write_config_word(pdev, msi_control_reg(pos), control & ~PCI_MSIX_FLAGS_ENABLE);
- }
- }
-
- return 0;
-}
-
static int cciss_controller_hard_reset(struct pci_dev *pdev,
void * __iomem vaddr, bool use_doorbell)
{
* states or using the doorbell register. */
static __devinit int cciss_kdump_hard_reset_controller(struct pci_dev *pdev)
{
- u16 saved_config_space[32];
u64 cfg_offset;
u32 cfg_base_addr;
u64 cfg_base_addr_index;
void __iomem *vaddr;
unsigned long paddr;
u32 misc_fw_support, active_transport;
- int rc, i;
+ int rc;
CfgTable_struct __iomem *cfgtable;
bool use_doorbell;
u32 board_id;
+ u16 command_register;
/* For controllers as old a the p600, this is very nearly
* the same thing as
* pci_set_power_state(pci_dev, PCI_D0);
* pci_restore_state(pci_dev);
*
- * but we can't use these nice canned kernel routines on
- * kexec, because they also check the MSI/MSI-X state in PCI
- * configuration space and do the wrong thing when it is
- * set/cleared. Also, the pci_save/restore_state functions
- * violate the ordering requirements for restoring the
- * configuration space from the CCISS document (see the
- * comment below). So we roll our own ....
- *
* For controllers newer than the P600, the pci power state
* method of resetting doesn't work so we have another way
* using the doorbell register.
return -ENODEV;
}
- for (i = 0; i < 32; i++)
- pci_read_config_word(pdev, 2*i, &saved_config_space[i]);
+ /* Save the PCI command register */
+ pci_read_config_word(pdev, 4, &command_register);
+ /* Turn the board off. This is so that later pci_restore_state()
+ * won't turn the board on before the rest of config space is ready.
+ */
+ pci_disable_device(pdev);
+ pci_save_state(pdev);
/* find the first memory BAR, so we can find the cfg table */
rc = cciss_pci_find_memory_BAR(pdev, &paddr);
rc = cciss_controller_hard_reset(pdev, vaddr, use_doorbell);
if (rc)
goto unmap_cfgtable;
-
- /* Restore the PCI configuration space. The Open CISS
- * Specification says, "Restore the PCI Configuration
- * Registers, offsets 00h through 60h. It is important to
- * restore the command register, 16-bits at offset 04h,
- * last. Do not restore the configuration status register,
- * 16-bits at offset 06h." Note that the offset is 2*i.
- */
- for (i = 0; i < 32; i++) {
- if (i == 2 || i == 3)
- continue;
- pci_write_config_word(pdev, 2*i, saved_config_space[i]);
+ pci_restore_state(pdev);
+ rc = pci_enable_device(pdev);
+ if (rc) {
+ dev_warn(&pdev->dev, "failed to enable device.\n");
+ goto unmap_cfgtable;
}
- wmb();
- pci_write_config_word(pdev, 4, saved_config_space[2]);
+ pci_write_config_word(pdev, 4, command_register);
/* Some devices (notably the HP Smart Array 5i Controller)
need a little pause here */
msleep(CCISS_POST_RESET_PAUSE_MSECS);
+ /* Wait for board to become not ready, then ready. */
+ dev_info(&pdev->dev, "Waiting for board to become ready.\n");
+ rc = cciss_wait_for_board_state(pdev, vaddr, BOARD_NOT_READY);
+ if (rc) /* Don't bail, might be E500, etc. which can't be reset */
+ dev_warn(&pdev->dev,
+ "failed waiting for board to become not ready\n");
+ rc = cciss_wait_for_board_state(pdev, vaddr, BOARD_READY);
+ if (rc) {
+ dev_warn(&pdev->dev,
+ "failed waiting for board to become ready\n");
+ goto unmap_cfgtable;
+ }
+ dev_info(&pdev->dev, "board ready.\n");
+
/* Controller should be in simple mode at this point. If it's not,
* It means we're on one of those controllers which doesn't support
* the doorbell reset method and on which the PCI power management reset
return 0; /* just try to do the kdump anyhow. */
if (rc)
return -ENODEV;
- if (cciss_reset_msi(pdev))
- return -ENODEV;
/* Now try to get the controller to respond to a no-op */
for (i = 0; i < CCISS_POST_RESET_NOOP_RETRIES; i++) {
}
}
kthread_stop(cciss_scan_thread);
- remove_proc_entry("driver/cciss", NULL);
+ if (proc_cciss)
+ remove_proc_entry("driver/cciss", NULL);
bus_unregister(&cciss_bus_type);
}
git.openpandora.org / pandora-kernel.git / blobdiff