* VIA VT8233c - UDMA100
* VIA VT8235 - UDMA133
* VIA VT8237 - UDMA133
+ * VIA VT8251 - UDMA133
*
* Most registers remain compatible across chips. Others start reserved
* and acquire sensible semantics if set to 1 (eg cable detect). A few
#include <linux/libata.h>
#define DRV_NAME "pata_via"
-#define DRV_VERSION "0.1.14"
+#define DRV_VERSION "0.2.0"
/*
* The following comes directly from Vojtech Pavlik's ide/pci/via82cxxx
u8 rev_max;
u16 flags;
} via_isa_bridges[] = {
+ { "vt8251", PCI_DEVICE_ID_VIA_8251, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
{ "cx700", PCI_DEVICE_ID_VIA_CX700, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
{ "vt6410", PCI_DEVICE_ID_VIA_6410, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST | VIA_NO_ENABLES},
{ "vt8237a", PCI_DEVICE_ID_VIA_8237A, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
- .max_sectors = ATA_MAX_SECTORS,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
.proc_name = DRV_NAME,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
+ .slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
};
static struct ata_port_operations via_port_ops = {
.host_stop = ata_host_stop
};
+/**
+ * via_config_fifo - set up the FIFO
+ * @pdev: PCI device
+ * @flags: configuration flags
+ *
+ * Set the FIFO properties for this device if neccessary. Used both on
+ * set up and on and the resume path
+ */
+
+static void via_config_fifo(struct pci_dev *pdev, unsigned int flags)
+{
+ u8 enable;
+
+ /* 0x40 low bits indicate enabled channels */
+ pci_read_config_byte(pdev, 0x40 , &enable);
+ enable &= 3;
+
+ if (flags & VIA_SET_FIFO) {
+ u8 fifo_setting[4] = {0x00, 0x60, 0x00, 0x20};
+ u8 fifo;
+
+ pci_read_config_byte(pdev, 0x43, &fifo);
+
+ /* Clear PREQ# until DDACK# for errata */
+ if (flags & VIA_BAD_PREQ)
+ fifo &= 0x7F;
+ else
+ fifo &= 0x9f;
+ /* Turn on FIFO for enabled channels */
+ fifo |= fifo_setting[enable];
+ pci_write_config_byte(pdev, 0x43, fifo);
+ }
+}
+
/**
* via_init_one - discovery callback
- * @pdev: PCI device ID
+ * @pdev: PCI device
* @id: PCI table info
*
* A VIA IDE interface has been discovered. Figure out what revision
/* Early VIA without UDMA support */
static struct ata_port_info via_mwdma_info = {
.sht = &via_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SETXFER_POLLING,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &via_port_ops
/* Ditto with IRQ masking required */
static struct ata_port_info via_mwdma_info_borked = {
.sht = &via_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SETXFER_POLLING,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.port_ops = &via_port_ops_noirq,
/* VIA UDMA 33 devices (and borked 66) */
static struct ata_port_info via_udma33_info = {
.sht = &via_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SETXFER_POLLING,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x7,
/* VIA UDMA 66 devices */
static struct ata_port_info via_udma66_info = {
.sht = &via_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SETXFER_POLLING,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x1f,
/* VIA UDMA 100 devices */
static struct ata_port_info via_udma100_info = {
.sht = &via_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SETXFER_POLLING,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x3f,
/* UDMA133 with bad AST (All current 133) */
static struct ata_port_info via_udma133_info = {
.sht = &via_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SETXFER_POLLING,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x7f, /* FIXME: should check north bridge */
}
/* Initialise the FIFO for the enabled channels. */
- if (config->flags & VIA_SET_FIFO) {
- u8 fifo_setting[4] = {0x00, 0x60, 0x00, 0x20};
- u8 fifo;
-
- pci_read_config_byte(pdev, 0x43, &fifo);
-
- /* Clear PREQ# until DDACK# for errata */
- if (config->flags & VIA_BAD_PREQ)
- fifo &= 0x7F;
- else
- fifo &= 0x9f;
- /* Turn on FIFO for enabled channels */
- fifo |= fifo_setting[enable];
- pci_write_config_byte(pdev, 0x43, fifo);
- }
+ via_config_fifo(pdev, config->flags);
+
/* Clock set up */
switch(config->flags & VIA_UDMA) {
case VIA_UDMA_NONE:
return ata_pci_init_one(pdev, port_info, 2);
}
+/**
+ * via_reinit_one - reinit after resume
+ * @pdev; PCI device
+ *
+ * Called when the VIA PATA device is resumed. We must then
+ * reconfigure the fifo and other setup we may have altered. In
+ * addition the kernel needs to have the resume methods on PCI
+ * quirk supported.
+ */
+
+static int via_reinit_one(struct pci_dev *pdev)
+{
+ u32 timing;
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
+ const struct via_isa_bridge *config = host->private_data;
+
+ via_config_fifo(pdev, config->flags);
+
+ if ((config->flags & VIA_UDMA) == VIA_UDMA_66) {
+ /* The 66 MHz devices require we enable the clock */
+ pci_read_config_dword(pdev, 0x50, &timing);
+ timing |= 0x80008;
+ pci_write_config_dword(pdev, 0x50, timing);
+ }
+ if (config->flags & VIA_BAD_CLK66) {
+ /* Disable the 66MHz clock on problem devices */
+ pci_read_config_dword(pdev, 0x50, &timing);
+ timing &= ~0x80008;
+ pci_write_config_dword(pdev, 0x50, timing);
+ }
+ return ata_pci_device_resume(pdev);
+}
+
static const struct pci_device_id via[] = {
{ PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_82C576_1), },
{ PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_82C586_1), },
.name = DRV_NAME,
.id_table = via,
.probe = via_init_one,
- .remove = ata_pci_remove_one
+ .remove = ata_pci_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = via_reinit_one,
};
static int __init via_init(void)
git.openpandora.org / pandora-kernel.git / blobdiff