static int no_timer_check;
-int disable_timer_pin_1 __initdata;
+static int disable_timer_pin_1 __initdata;
int timer_over_8254 __initdata = 0;
FINAL; \
}
+union entry_union {
+ struct { u32 w1, w2; };
+ struct IO_APIC_route_entry entry;
+};
+
+static struct IO_APIC_route_entry ioapic_read_entry(int apic, int pin)
+{
+ union entry_union eu;
+ unsigned long flags;
+ spin_lock_irqsave(&ioapic_lock, flags);
+ eu.w1 = io_apic_read(apic, 0x10 + 2 * pin);
+ eu.w2 = io_apic_read(apic, 0x11 + 2 * pin);
+ spin_unlock_irqrestore(&ioapic_lock, flags);
+ return eu.entry;
+}
+
+static void ioapic_write_entry(int apic, int pin, struct IO_APIC_route_entry e)
+{
+ unsigned long flags;
+ union entry_union eu;
+ eu.entry = e;
+ spin_lock_irqsave(&ioapic_lock, flags);
+ io_apic_write(apic, 0x10 + 2*pin, eu.w1);
+ io_apic_write(apic, 0x11 + 2*pin, eu.w2);
+ spin_unlock_irqrestore(&ioapic_lock, flags);
+}
+
#ifdef CONFIG_SMP
static void set_ioapic_affinity_irq(unsigned int irq, cpumask_t mask)
{
static void clear_IO_APIC_pin(unsigned int apic, unsigned int pin)
{
struct IO_APIC_route_entry entry;
- unsigned long flags;
/* Check delivery_mode to be sure we're not clearing an SMI pin */
- spin_lock_irqsave(&ioapic_lock, flags);
- *(((int*)&entry) + 0) = io_apic_read(apic, 0x10 + 2 * pin);
- *(((int*)&entry) + 1) = io_apic_read(apic, 0x11 + 2 * pin);
- spin_unlock_irqrestore(&ioapic_lock, flags);
+ entry = ioapic_read_entry(apic, pin);
if (entry.delivery_mode == dest_SMI)
return;
/*
*/
memset(&entry, 0, sizeof(entry));
entry.mask = 1;
- spin_lock_irqsave(&ioapic_lock, flags);
- io_apic_write(apic, 0x10 + 2 * pin, *(((int *)&entry) + 0));
- io_apic_write(apic, 0x11 + 2 * pin, *(((int *)&entry) + 1));
- spin_unlock_irqrestore(&ioapic_lock, flags);
+ ioapic_write_entry(apic, pin, entry);
}
static void clear_IO_APIC (void)
clear_IO_APIC_pin(apic, pin);
}
-/*
- * support for broken MP BIOSs, enables hand-redirection of PIRQ0-7 to
- * specific CPU-side IRQs.
- */
-
-#define MAX_PIRQS 8
-static int pirq_entries [MAX_PIRQS];
-static int pirqs_enabled;
int skip_ioapic_setup;
int ioapic_force;
static int __init disable_ioapic_setup(char *str)
{
skip_ioapic_setup = 1;
- return 1;
+ return 0;
}
+early_param("noapic", disable_ioapic_setup);
-static int __init enable_ioapic_setup(char *str)
+/* Actually the next is obsolete, but keep it for paranoid reasons -AK */
+static int __init disable_timer_pin_setup(char *arg)
{
- ioapic_force = 1;
- skip_ioapic_setup = 0;
+ disable_timer_pin_1 = 1;
return 1;
}
-
-__setup("noapic", disable_ioapic_setup);
-__setup("apic", enable_ioapic_setup);
+__setup("disable_timer_pin_1", disable_timer_pin_setup);
static int __init setup_disable_8254_timer(char *s)
{
__setup("disable_8254_timer", setup_disable_8254_timer);
__setup("enable_8254_timer", setup_enable_8254_timer);
-#include <asm/pci-direct.h>
-#include <linux/pci_ids.h>
-#include <linux/pci.h>
-
-
-#ifdef CONFIG_ACPI
-
-static int nvidia_hpet_detected __initdata;
-
-static int __init nvidia_hpet_check(unsigned long phys, unsigned long size)
-{
- nvidia_hpet_detected = 1;
- return 0;
-}
-#endif
-
-/* Temporary Hack. Nvidia and VIA boards currently only work with IO-APIC
- off. Check for an Nvidia or VIA PCI bridge and turn it off.
- Use pci direct infrastructure because this runs before the PCI subsystem.
-
- Can be overwritten with "apic"
-
- And another hack to disable the IOMMU on VIA chipsets.
-
- ... and others. Really should move this somewhere else.
-
- Kludge-O-Rama. */
-void __init check_ioapic(void)
-{
- int num,slot,func;
- /* Poor man's PCI discovery */
- for (num = 0; num < 32; num++) {
- for (slot = 0; slot < 32; slot++) {
- for (func = 0; func < 8; func++) {
- u32 class;
- u32 vendor;
- u8 type;
- class = read_pci_config(num,slot,func,
- PCI_CLASS_REVISION);
- if (class == 0xffffffff)
- break;
-
- if ((class >> 16) != PCI_CLASS_BRIDGE_PCI)
- continue;
-
- vendor = read_pci_config(num, slot, func,
- PCI_VENDOR_ID);
- vendor &= 0xffff;
- switch (vendor) {
- case PCI_VENDOR_ID_VIA:
-#ifdef CONFIG_IOMMU
- if ((end_pfn > MAX_DMA32_PFN ||
- force_iommu) &&
- !iommu_aperture_allowed) {
- printk(KERN_INFO
- "Looks like a VIA chipset. Disabling IOMMU. Override with \"iommu=allowed\"\n");
- iommu_aperture_disabled = 1;
- }
-#endif
- return;
- case PCI_VENDOR_ID_NVIDIA:
-#ifdef CONFIG_ACPI
- /*
- * All timer overrides on Nvidia are
- * wrong unless HPET is enabled.
- */
- nvidia_hpet_detected = 0;
- acpi_table_parse(ACPI_HPET,
- nvidia_hpet_check);
- if (nvidia_hpet_detected == 0) {
- acpi_skip_timer_override = 1;
- printk(KERN_INFO "Nvidia board "
- "detected. Ignoring ACPI "
- "timer override.\n");
- }
-#endif
- /* RED-PEN skip them on mptables too? */
- return;
-
- /* This should be actually default, but
- for 2.6.16 let's do it for ATI only where
- it's really needed. */
- case PCI_VENDOR_ID_ATI:
- if (timer_over_8254 == 1) {
- timer_over_8254 = 0;
- printk(KERN_INFO
- "ATI board detected. Disabling timer routing over 8254.\n");
- }
- return;
- }
-
-
- /* No multi-function device? */
- type = read_pci_config_byte(num,slot,func,
- PCI_HEADER_TYPE);
- if (!(type & 0x80))
- break;
- }
- }
- }
-}
-
-static int __init ioapic_pirq_setup(char *str)
-{
- int i, max;
- int ints[MAX_PIRQS+1];
-
- get_options(str, ARRAY_SIZE(ints), ints);
-
- for (i = 0; i < MAX_PIRQS; i++)
- pirq_entries[i] = -1;
-
- pirqs_enabled = 1;
- apic_printk(APIC_VERBOSE, "PIRQ redirection, working around broken MP-BIOS.\n");
- max = MAX_PIRQS;
- if (ints[0] < MAX_PIRQS)
- max = ints[0];
-
- for (i = 0; i < max; i++) {
- apic_printk(APIC_VERBOSE, "... PIRQ%d -> IRQ %d\n", i, ints[i+1]);
- /*
- * PIRQs are mapped upside down, usually.
- */
- pirq_entries[MAX_PIRQS-i-1] = ints[i+1];
- }
- return 1;
-}
-
-__setup("pirq=", ioapic_pirq_setup);
/*
* Find the IRQ entry number of a certain pin.
for (i = 0; i < mp_irq_entries; i++) {
int lbus = mp_irqs[i].mpc_srcbus;
- if ((mp_bus_id_to_type[lbus] == MP_BUS_ISA ||
- mp_bus_id_to_type[lbus] == MP_BUS_EISA ||
- mp_bus_id_to_type[lbus] == MP_BUS_MCA) &&
+ if (test_bit(lbus, mp_bus_not_pci) &&
(mp_irqs[i].mpc_irqtype == type) &&
(mp_irqs[i].mpc_srcbusirq == irq))
for (i = 0; i < mp_irq_entries; i++) {
int lbus = mp_irqs[i].mpc_srcbus;
- if ((mp_bus_id_to_type[lbus] == MP_BUS_ISA ||
- mp_bus_id_to_type[lbus] == MP_BUS_EISA ||
- mp_bus_id_to_type[lbus] == MP_BUS_MCA) &&
+ if (test_bit(lbus, mp_bus_not_pci) &&
(mp_irqs[i].mpc_irqtype == type) &&
(mp_irqs[i].mpc_srcbusirq == irq))
break;
mp_irqs[i].mpc_dstapic == MP_APIC_ALL)
break;
- if ((mp_bus_id_to_type[lbus] == MP_BUS_PCI) &&
+ if (!test_bit(lbus, mp_bus_not_pci) &&
!mp_irqs[i].mpc_irqtype &&
(bus == lbus) &&
(slot == ((mp_irqs[i].mpc_srcbusirq >> 2) & 0x1f))) {
return best_guess;
}
-/*
- * EISA Edge/Level control register, ELCR
- */
-static int EISA_ELCR(unsigned int irq)
-{
- if (irq < 16) {
- unsigned int port = 0x4d0 + (irq >> 3);
- return (inb(port) >> (irq & 7)) & 1;
- }
- apic_printk(APIC_VERBOSE, "Broken MPtable reports ISA irq %d\n", irq);
- return 0;
-}
-
-/* EISA interrupts are always polarity zero and can be edge or level
- * trigger depending on the ELCR value. If an interrupt is listed as
- * EISA conforming in the MP table, that means its trigger type must
- * be read in from the ELCR */
-
-#define default_EISA_trigger(idx) (EISA_ELCR(mp_irqs[idx].mpc_srcbusirq))
-#define default_EISA_polarity(idx) (0)
-
/* ISA interrupts are always polarity zero edge triggered,
* when listed as conforming in the MP table. */
#define default_PCI_trigger(idx) (1)
#define default_PCI_polarity(idx) (1)
-/* MCA interrupts are always polarity zero level triggered,
- * when listed as conforming in the MP table. */
-
-#define default_MCA_trigger(idx) (1)
-#define default_MCA_polarity(idx) (0)
-
static int __init MPBIOS_polarity(int idx)
{
int bus = mp_irqs[idx].mpc_srcbus;
switch (mp_irqs[idx].mpc_irqflag & 3)
{
case 0: /* conforms, ie. bus-type dependent polarity */
- {
- switch (mp_bus_id_to_type[bus])
- {
- case MP_BUS_ISA: /* ISA pin */
- {
- polarity = default_ISA_polarity(idx);
- break;
- }
- case MP_BUS_EISA: /* EISA pin */
- {
- polarity = default_EISA_polarity(idx);
- break;
- }
- case MP_BUS_PCI: /* PCI pin */
- {
- polarity = default_PCI_polarity(idx);
- break;
- }
- case MP_BUS_MCA: /* MCA pin */
- {
- polarity = default_MCA_polarity(idx);
- break;
- }
- default:
- {
- printk(KERN_WARNING "broken BIOS!!\n");
- polarity = 1;
- break;
- }
- }
+ if (test_bit(bus, mp_bus_not_pci))
+ polarity = default_ISA_polarity(idx);
+ else
+ polarity = default_PCI_polarity(idx);
break;
- }
case 1: /* high active */
{
polarity = 0;
switch ((mp_irqs[idx].mpc_irqflag>>2) & 3)
{
case 0: /* conforms, ie. bus-type dependent */
- {
- switch (mp_bus_id_to_type[bus])
- {
- case MP_BUS_ISA: /* ISA pin */
- {
- trigger = default_ISA_trigger(idx);
- break;
- }
- case MP_BUS_EISA: /* EISA pin */
- {
- trigger = default_EISA_trigger(idx);
- break;
- }
- case MP_BUS_PCI: /* PCI pin */
- {
- trigger = default_PCI_trigger(idx);
- break;
- }
- case MP_BUS_MCA: /* MCA pin */
- {
- trigger = default_MCA_trigger(idx);
- break;
- }
- default:
- {
- printk(KERN_WARNING "broken BIOS!!\n");
- trigger = 1;
- break;
- }
- }
+ if (test_bit(bus, mp_bus_not_pci))
+ trigger = default_ISA_trigger(idx);
+ else
+ trigger = default_PCI_trigger(idx);
break;
- }
case 1: /* edge */
{
trigger = 0;
if (mp_irqs[idx].mpc_dstirq != pin)
printk(KERN_ERR "broken BIOS or MPTABLE parser, ayiee!!\n");
- switch (mp_bus_id_to_type[bus])
- {
- case MP_BUS_ISA: /* ISA pin */
- case MP_BUS_EISA:
- case MP_BUS_MCA:
- {
- irq = mp_irqs[idx].mpc_srcbusirq;
- break;
- }
- case MP_BUS_PCI: /* PCI pin */
- {
- /*
- * PCI IRQs are mapped in order
- */
- i = irq = 0;
- while (i < apic)
- irq += nr_ioapic_registers[i++];
- irq += pin;
- irq = gsi_irq_sharing(irq);
- break;
- }
- default:
- {
- printk(KERN_ERR "unknown bus type %d.\n",bus);
- irq = 0;
- break;
- }
- }
- BUG_ON(irq >= NR_IRQS);
-
- /*
- * PCI IRQ command line redirection. Yes, limits are hardcoded.
- */
- if ((pin >= 16) && (pin <= 23)) {
- if (pirq_entries[pin-16] != -1) {
- if (!pirq_entries[pin-16]) {
- apic_printk(APIC_VERBOSE, "disabling PIRQ%d\n", pin-16);
- } else {
- irq = pirq_entries[pin-16];
- apic_printk(APIC_VERBOSE, "using PIRQ%d -> IRQ %d\n",
- pin-16, irq);
- }
- }
+ if (test_bit(bus, mp_bus_not_pci)) {
+ irq = mp_irqs[idx].mpc_srcbusirq;
+ } else {
+ /*
+ * PCI IRQs are mapped in order
+ */
+ i = irq = 0;
+ while (i < apic)
+ irq += nr_ioapic_registers[i++];
+ irq += pin;
+ irq = gsi_irq_sharing(irq);
}
BUG_ON(irq >= NR_IRQS);
return irq;
if (!apic && (irq < 16))
disable_8259A_irq(irq);
}
+ ioapic_write_entry(apic, pin, entry);
+
spin_lock_irqsave(&ioapic_lock, flags);
- io_apic_write(apic, 0x11+2*pin, *(((int *)&entry)+1));
- io_apic_write(apic, 0x10+2*pin, *(((int *)&entry)+0));
set_native_irq_info(irq, TARGET_CPUS);
spin_unlock_irqrestore(&ioapic_lock, flags);
}
for (i = 0; i <= reg_01.bits.entries; i++) {
struct IO_APIC_route_entry entry;
- spin_lock_irqsave(&ioapic_lock, flags);
- *(((int *)&entry)+0) = io_apic_read(apic, 0x10+i*2);
- *(((int *)&entry)+1) = io_apic_read(apic, 0x11+i*2);
- spin_unlock_irqrestore(&ioapic_lock, flags);
+ entry = ioapic_read_entry(apic, i);
printk(KERN_DEBUG " %02x %03X %02X ",
i,
irq_2_pin[i].pin = -1;
irq_2_pin[i].next = 0;
}
- if (!pirqs_enabled)
- for (i = 0; i < MAX_PIRQS; i++)
- pirq_entries[i] = -1;
/*
* The number of IO-APIC IRQ registers (== #pins):
/* See if any of the pins is in ExtINT mode */
for (pin = 0; pin < nr_ioapic_registers[apic]; pin++) {
struct IO_APIC_route_entry entry;
- spin_lock_irqsave(&ioapic_lock, flags);
- *(((int *)&entry) + 0) = io_apic_read(apic, 0x10 + 2 * pin);
- *(((int *)&entry) + 1) = io_apic_read(apic, 0x11 + 2 * pin);
- spin_unlock_irqrestore(&ioapic_lock, flags);
-
+ entry = ioapic_read_entry(apic, pin);
/* If the interrupt line is enabled and in ExtInt mode
* I have found the pin where the i8259 is connected.
*/
if (ioapic_i8259.pin != -1) {
struct IO_APIC_route_entry entry;
- unsigned long flags;
memset(&entry, 0, sizeof(entry));
entry.mask = 0; /* Enabled */
/*
* Add it to the IO-APIC irq-routing table:
*/
- spin_lock_irqsave(&ioapic_lock, flags);
- io_apic_write(ioapic_i8259.apic, 0x11+2*ioapic_i8259.pin,
- *(((int *)&entry)+1));
- io_apic_write(ioapic_i8259.apic, 0x10+2*ioapic_i8259.pin,
- *(((int *)&entry)+0));
- spin_unlock_irqrestore(&ioapic_lock, flags);
+ ioapic_write_entry(ioapic_i8259.apic, ioapic_i8259.pin, entry);
}
disconnect_bsp_APIC(ioapic_i8259.pin != -1);
}
-/*
- * function to set the IO-APIC physical IDs based on the
- * values stored in the MPC table.
- *
- * by Matt Domsch <Matt_Domsch@dell.com> Tue Dec 21 12:25:05 CST 1999
- */
-
-static void __init setup_ioapic_ids_from_mpc (void)
-{
- union IO_APIC_reg_00 reg_00;
- int apic;
- int i;
- unsigned char old_id;
- unsigned long flags;
-
- /*
- * Set the IOAPIC ID to the value stored in the MPC table.
- */
- for (apic = 0; apic < nr_ioapics; apic++) {
-
- /* Read the register 0 value */
- spin_lock_irqsave(&ioapic_lock, flags);
- reg_00.raw = io_apic_read(apic, 0);
- spin_unlock_irqrestore(&ioapic_lock, flags);
-
- old_id = mp_ioapics[apic].mpc_apicid;
-
-
- printk(KERN_INFO "Using IO-APIC %d\n", mp_ioapics[apic].mpc_apicid);
-
-
- /*
- * We need to adjust the IRQ routing table
- * if the ID changed.
- */
- if (old_id != mp_ioapics[apic].mpc_apicid)
- for (i = 0; i < mp_irq_entries; i++)
- if (mp_irqs[i].mpc_dstapic == old_id)
- mp_irqs[i].mpc_dstapic
- = mp_ioapics[apic].mpc_apicid;
-
- /*
- * Read the right value from the MPC table and
- * write it into the ID register.
- */
- apic_printk(APIC_VERBOSE,KERN_INFO "...changing IO-APIC physical APIC ID to %d ...",
- mp_ioapics[apic].mpc_apicid);
-
- reg_00.bits.ID = mp_ioapics[apic].mpc_apicid;
- spin_lock_irqsave(&ioapic_lock, flags);
- io_apic_write(apic, 0, reg_00.raw);
- spin_unlock_irqrestore(&ioapic_lock, flags);
-
- /*
- * Sanity check
- */
- spin_lock_irqsave(&ioapic_lock, flags);
- reg_00.raw = io_apic_read(apic, 0);
- spin_unlock_irqrestore(&ioapic_lock, flags);
- if (reg_00.bits.ID != mp_ioapics[apic].mpc_apicid)
- printk("could not set ID!\n");
- else
- apic_printk(APIC_VERBOSE," ok.\n");
- }
-}
-
/*
* There is a nasty bug in some older SMP boards, their mptable lies
* about the timer IRQ. We do the following to work around the situation:
apic_printk(APIC_VERBOSE, "ENABLING IO-APIC IRQs\n");
- /*
- * Set up the IO-APIC IRQ routing table.
- */
- if (!acpi_ioapic)
- setup_ioapic_ids_from_mpc();
sync_Arb_IDs();
setup_IO_APIC_irqs();
init_IO_APIC_traps();
{
struct IO_APIC_route_entry *entry;
struct sysfs_ioapic_data *data;
- unsigned long flags;
int i;
data = container_of(dev, struct sysfs_ioapic_data, dev);
entry = data->entry;
- spin_lock_irqsave(&ioapic_lock, flags);
- for (i = 0; i < nr_ioapic_registers[dev->id]; i ++, entry ++ ) {
- *(((int *)entry) + 1) = io_apic_read(dev->id, 0x11 + 2 * i);
- *(((int *)entry) + 0) = io_apic_read(dev->id, 0x10 + 2 * i);
- }
- spin_unlock_irqrestore(&ioapic_lock, flags);
+ for (i = 0; i < nr_ioapic_registers[dev->id]; i ++, entry ++ )
+ *entry = ioapic_read_entry(dev->id, i);
return 0;
}
reg_00.bits.ID = mp_ioapics[dev->id].mpc_apicid;
io_apic_write(dev->id, 0, reg_00.raw);
}
- for (i = 0; i < nr_ioapic_registers[dev->id]; i ++, entry ++ ) {
- io_apic_write(dev->id, 0x11+2*i, *(((int *)entry)+1));
- io_apic_write(dev->id, 0x10+2*i, *(((int *)entry)+0));
- }
spin_unlock_irqrestore(&ioapic_lock, flags);
+ for (i = 0; i < nr_ioapic_registers[dev->id]; i++)
+ ioapic_write_entry(dev->id, i, entry[i]);
return 0;
}
#define IO_APIC_MAX_ID 0xFE
-int __init io_apic_get_version (int ioapic)
-{
- union IO_APIC_reg_01 reg_01;
- unsigned long flags;
-
- spin_lock_irqsave(&ioapic_lock, flags);
- reg_01.raw = io_apic_read(ioapic, 1);
- spin_unlock_irqrestore(&ioapic_lock, flags);
-
- return reg_01.bits.version;
-}
-
-
int __init io_apic_get_redir_entries (int ioapic)
{
union IO_APIC_reg_01 reg_01;
if (!ioapic && (irq < 16))
disable_8259A_irq(irq);
+ ioapic_write_entry(ioapic, pin, entry);
+
spin_lock_irqsave(&ioapic_lock, flags);
- io_apic_write(ioapic, 0x11+2*pin, *(((int *)&entry)+1));
- io_apic_write(ioapic, 0x10+2*pin, *(((int *)&entry)+0));
- set_native_irq_info(use_pci_vector() ? entry.vector : irq, TARGET_CPUS);
+ set_native_irq_info(use_pci_vector() ? entry.vector : irq, TARGET_CPUS);
spin_unlock_irqrestore(&ioapic_lock, flags);
return 0;
git.openpandora.org / pandora-kernel.git / blobdiff