#endif
#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+ .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
static struct resource smc91x_resources[] = {
{
.name = "smc91x-regs",
.id = 0,
.num_resources = ARRAY_SIZE(smc91x_resources),
.resource = smc91x_resources,
+ .dev = {
+ .platform_data = &smc91x_info,
+ },
};
#endif
static struct resource dm9000_resources[] = {
[0] = {
.start = 0x203FB800,
- .end = 0x203FB800 + 8,
+ .end = 0x203FB800 + 1,
.flags = IORESOURCE_MEM,
},
[1] = {
+ .start = 0x203FB804,
+ .end = 0x203FB804 + 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
.start = IRQ_PF9,
.end = IRQ_PF9,
.flags = (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),
};
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD1836) \
- || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
+#if defined(CONFIG_SND_BF5XX_SOC_AD1938) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD1938_MODULE)
+static struct bfin5xx_spi_chip ad1938_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+ .cs_gpio = GPIO_PF5,
+};
+#endif
+
+#if defined(CONFIG_INPUT_EVAL_AD7147EBZ)
+#include <linux/input.h>
+#include <linux/input/ad714x.h>
+static struct bfin5xx_spi_chip ad7147_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 16,
};
+
+static struct ad714x_slider_plat slider_plat[] = {
+ {
+ .start_stage = 0,
+ .end_stage = 7,
+ .max_coord = 128,
+ },
+};
+
+static struct ad714x_button_plat button_plat[] = {
+ {
+ .keycode = BTN_FORWARD,
+ .l_mask = 0,
+ .h_mask = 0x600,
+ },
+ {
+ .keycode = BTN_LEFT,
+ .l_mask = 0,
+ .h_mask = 0x500,
+ },
+ {
+ .keycode = BTN_MIDDLE,
+ .l_mask = 0,
+ .h_mask = 0x800,
+ },
+ {
+ .keycode = BTN_RIGHT,
+ .l_mask = 0x100,
+ .h_mask = 0x400,
+ },
+ {
+ .keycode = BTN_BACK,
+ .l_mask = 0x200,
+ .h_mask = 0x400,
+ },
+};
+static struct ad714x_platform_data ad7147_platfrom_data = {
+ .slider_num = 1,
+ .button_num = 5,
+ .slider = slider_plat,
+ .button = button_plat,
+ .stage_cfg_reg = {
+ {0xFBFF, 0x1FFF, 0, 0x2626, 1600, 1600, 1600, 1600},
+ {0xEFFF, 0x1FFF, 0, 0x2626, 1650, 1650, 1650, 1650},
+ {0xFFFF, 0x1FFE, 0, 0x2626, 1650, 1650, 1650, 1650},
+ {0xFFFF, 0x1FFB, 0, 0x2626, 1650, 1650, 1650, 1650},
+ {0xFFFF, 0x1FEF, 0, 0x2626, 1650, 1650, 1650, 1650},
+ {0xFFFF, 0x1FBF, 0, 0x2626, 1650, 1650, 1650, 1650},
+ {0xFFFF, 0x1EFF, 0, 0x2626, 1650, 1650, 1650, 1650},
+ {0xFFFF, 0x1BFF, 0, 0x2626, 1600, 1600, 1600, 1600},
+ {0xFF7B, 0x3FFF, 0x506, 0x2626, 1100, 1100, 1150, 1150},
+ {0xFDFE, 0x3FFF, 0x606, 0x2626, 1100, 1100, 1150, 1150},
+ {0xFEBA, 0x1FFF, 0x1400, 0x2626, 1200, 1200, 1300, 1300},
+ {0xFFEF, 0x1FFF, 0x0, 0x2626, 1100, 1100, 1150, 1150},
+ },
+ .sys_cfg_reg = {0x2B2, 0x0, 0x3233, 0x819, 0x832, 0xCFF, 0xCFF, 0x0},
+};
+#endif
+
+#if defined(CONFIG_INPUT_EVAL_AD7142EB)
+#include <linux/input.h>
+#include <linux/input/ad714x.h>
+static struct ad714x_button_plat button_plat[] = {
+ {
+ .keycode = BTN_1,
+ .l_mask = 0,
+ .h_mask = 0x1,
+ },
+ {
+ .keycode = BTN_2,
+ .l_mask = 0,
+ .h_mask = 0x2,
+ },
+ {
+ .keycode = BTN_3,
+ .l_mask = 0,
+ .h_mask = 0x4,
+ },
+ {
+ .keycode = BTN_4,
+ .l_mask = 0x0,
+ .h_mask = 0x8,
+ },
+};
+static struct ad714x_platform_data ad7142_platfrom_data = {
+ .button_num = 4,
+ .button = button_plat,
+ .stage_cfg_reg = {
+ /* fixme: figure out right setting for all comoponent according
+ * to hardware feature of EVAL-AD7142EB board */
+ {0xE7FF, 0x3FFF, 0x0005, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
+ {0xFDBF, 0x3FFF, 0x0001, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
+ {0xFFFF, 0x2DFF, 0x0001, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
+ {0xFFFF, 0x37BF, 0x0001, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
+ {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+ {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+ {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+ {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+ {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+ {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+ {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+ {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+ },
+ .sys_cfg_reg = {0x0B2, 0x0, 0x690, 0x664, 0x290F, 0xF, 0xF, 0x0},
+};
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0,
.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
- .ctl_reg = 0x4, /* send zero */
- .enable_dma = 0,
- .bits_per_word = 8,
- .cs_change_per_word = 1,
+ .pio_interrupt = 0,
};
#endif
},
#endif
-#if defined(CONFIG_SND_BLACKFIN_AD1836) \
- || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
+ || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
{
- .modalias = "ad1836-spi",
+ .modalias = "ad1836",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .chip_select = 4,/* CONFIG_SND_BLACKFIN_SPI_PFBIT */
.controller_data = &ad1836_spi_chip_info,
+ .mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
+
+#if defined(CONFIG_SND_BF5XX_SOC_AD1938) || defined(CONFIG_SND_BF5XX_SOC_AD1938_MODULE)
{
- .modalias = "ad9960-spi",
- .max_speed_hz = 10000000, /* max spi clock (SCK) speed in HZ */
+ .modalias = "ad1938",
+ .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = 1,
- .controller_data = &ad9960_spi_chip_info,
+ .chip_select = 0,/* CONFIG_SND_BLACKFIN_SPI_PFBIT */
+ .controller_data = &ad1938_spi_chip_info,
+ .mode = SPI_MODE_3,
},
#endif
+
+#if defined(CONFIG_INPUT_EVAL_AD7147EBZ)
+ {
+ .modalias = "ad714x_captouch",
+ .max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
+ .irq = IRQ_PF4,
+ .bus_num = 0,
+ .chip_select = 5,
+ .mode = SPI_MODE_3,
+ .platform_data = &ad7147_platfrom_data,
+ .controller_data = &ad7147_spi_chip_info,
+ },
+#endif
+
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
.modalias = "mmc_spi",
.mode = SPI_MODE_3,
},
#endif
-#if defined(CONFIG_PBX)
- {
- .modalias = "fxs-spi",
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 8 - CONFIG_J11_JUMPER,
- .controller_data = &spi_si3xxx_chip_info,
- .mode = SPI_MODE_3,
- },
- {
- .modalias = "fxo-spi",
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 8 - CONFIG_J19_JUMPER,
- .controller_data = &spi_si3xxx_chip_info,
- .mode = SPI_MODE_3,
- },
-#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
{
.modalias = "ad7877",
[1] = {
.start = CH_SPI,
.end = CH_SPI,
+ .flags = IORESOURCE_DMA,
+ },
+ [2] = {
+ .start = IRQ_SPI,
+ .end = IRQ_SPI,
.flags = IORESOURCE_IRQ,
},
};
#if defined(CONFIG_KEYBOARD_ADP5588) || defined(CONFIG_KEYBOARD_ADP5588_MODULE)
#include <linux/input.h>
-#include <linux/i2c/adp5588_keys.h>
+#include <linux/i2c/adp5588.h>
static const unsigned short adp5588_keymap[ADP5588_KEYMAPSIZE] = {
[0] = KEY_GRAVE,
[1] = KEY_1,
#endif
+#if defined(CONFIG_GPIO_ADP5588) || defined(CONFIG_GPIO_ADP5588_MODULE)
+#include <linux/i2c/adp5588.h>
+static struct adp5588_gpio_platfrom_data adp5588_gpio_data = {
+ .gpio_start = 50,
+ .pullup_dis_mask = 0,
+};
+#endif
+
static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_JOYSTICK_AD7142) || defined(CONFIG_JOYSTICK_AD7142_MODULE)
+#if defined(CONFIG_INPUT_EVAL_AD7142EB)
{
- I2C_BOARD_INFO("ad7142_joystick", 0x2C),
+ I2C_BOARD_INFO("ad7142_captouch", 0x2C),
.irq = IRQ_PG5,
+ .platform_data = (void *)&ad7142_platfrom_data,
},
#endif
#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
I2C_BOARD_INFO("pcf8574_lcd", 0x22),
},
#endif
-#if defined(CONFIG_TWI_KEYPAD) || defined(CONFIG_TWI_KEYPAD_MODULE)
+#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
{
I2C_BOARD_INFO("pcf8574_keypad", 0x27),
.irq = IRQ_PG6,
.platform_data = (void *)&adxl34x_info,
},
#endif
+#if defined(CONFIG_GPIO_ADP5588) || defined(CONFIG_GPIO_ADP5588_MODULE)
+ {
+ I2C_BOARD_INFO("adp5588-gpio", 0x34),
+ .platform_data = (void *)&adp5588_gpio_data,
+ },
+#endif
};
#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
},
};
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+static struct platform_device bfin_tdm = {
+ .name = "bfin-tdm",
+ /* TODO: add platform data here */
+};
+#endif
+
static struct platform_device *stamp_devices[] __initdata = {
&bfin_dpmc,
#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
&stamp_flash_device,
#endif
+
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+ &bfin_tdm,
+#endif
};
static int __init stamp_init(void)
platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
-#if (defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)) \
- && defined(PATA_INT)
- irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
-#endif
-
return 0;
}
git.openpandora.org / pandora-kernel.git / blobdiff