bool
depends on (BFIN533_EZKIT || BFIN561_EZKIT \
|| BFIN533_BLUETECHNIX_CM || BFIN537_BLUETECHNIX_CM \
- || H8606_HVSISTEMAS)
+ || H8606_HVSISTEMAS || BFIN527_BLUETECHNIX_CM)
default y
config MEM_MT48LC32M8A2_75
default "45" if BFIN533_STAMP
default "20" if (BFIN537_STAMP || BFIN527_EZKIT || BFIN548_EZKIT || BFIN548_BLUETECHNIX_CM)
default "22" if BFIN533_BLUETECHNIX_CM
- default "20" if BFIN537_BLUETECHNIX_CM
- default "20" if BFIN561_BLUETECHNIX_CM
+ default "20" if (BFIN537_BLUETECHNIX_CM || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM)
default "20" if BFIN561_EZKIT
default "16" if H8606_HVSISTEMAS
help
endchoice
-config L1_MAX_PIECE
- int "Set the max L1 SRAM pieces"
- default 16
- help
- Set the max memory pieces for the L1 SRAM allocation algorithm.
- Min value is 16. Max value is 1024.
-
-
config MPU
bool "Enable the memory protection unit (EXPERIMENTAL)"
default n
plugged into slots found on all modern laptop computers. Another
example, used on modern desktops as well as laptops, is USB.
- Enable HOTPLUG and KMOD, and build a modular kernel. Get agent
- software (at <http://linux-hotplug.sourceforge.net/>) and install it.
+ Enable HOTPLUG and build a modular kernel. Get agent software
+ (from <http://linux-hotplug.sourceforge.net/>) and install it.
Then your kernel will automatically call out to a user mode "policy
agent" (/sbin/hotplug) to load modules and set up software needed
to use devices as you hotplug them.
depends on !SMP
choice
- prompt "Default Power Saving Mode"
+ prompt "Standby Power Saving Mode"
depends on PM
default PM_BFIN_SLEEP_DEEPER
config PM_BFIN_SLEEP_DEEPER
normal during Sleep Deeper, due to the reduced SCLK frequency.
When in the sleep mode, system DMA access to L1 memory is not supported.
+ If unsure, select "Sleep Deeper".
+
config PM_BFIN_SLEEP
bool "Sleep"
help
dissipation by disabling the clock to the processor core (CCLK).
The PLL and system clock (SCLK), however, continue to operate in
this mode. Typically an external event or RTC activity will wake
- up the processor. When in the sleep mode,
- system DMA access to L1 memory is not supported.
+ up the processor. When in the sleep mode, system DMA access to L1
+ memory is not supported.
+
+ If unsure, select "Sleep Deeper".
endchoice
config PM_WAKEUP_BY_GPIO
- bool "Cause Wakeup Event by GPIO"
+ bool "Allow Wakeup from Standby by GPIO"
config PM_WAKEUP_GPIO_NUMBER
- int "Wakeup GPIO number"
+ int "GPIO number"
range 0 47
depends on PM_WAKEUP_BY_GPIO
default 2 if BFIN537_STAMP
bool "Both EDGE"
endchoice
+comment "Possible Suspend Mem / Hibernate Wake-Up Sources"
+ depends on PM
+
+config PM_BFIN_WAKE_RTC
+ bool "Allow Wake-Up from RESET and on-chip RTC"
+ depends on PM
+ default n
+ help
+ Enable RTC Wake-Up (Voltage Regulator Power-Up)
+
+config PM_BFIN_WAKE_PH6
+ bool "Allow Wake-Up from on-chip PHY or PH6 GP"
+ depends on PM && (BF52x || BF534 || BF536 || BF537)
+ default n
+ help
+ Enable PHY and PH6 GP Wake-Up (Voltage Regulator Power-Up)
+
+config PM_BFIN_WAKE_CAN
+ bool "Allow Wake-Up from on-chip CAN0/1"
+ depends on PM && (BF54x || BF534 || BF536 || BF537)
+ default n
+ help
+ Enable CAN0/1 Wake-Up (Voltage Regulator Power-Up)
+
+config PM_BFIN_WAKE_GP
+ bool "Allow Wake-Up from GPIOs"
+ depends on PM && BF54x
+ default n
+ help
+ Enable General-Purpose Wake-Up (Voltage Regulator Power-Up)
+
+config PM_BFIN_WAKE_USB
+ bool "Allow Wake-Up from on-chip USB"
+ depends on PM && (BF54x || BF52x)
+ default n
+ help
+ Enable USB Wake-Up (Voltage Regulator Power-Up)
+
+config PM_BFIN_WAKE_KEYPAD
+ bool "Allow Wake-Up from on-chip Keypad"
+ depends on PM && BF54x
+ default n
+ help
+ Enable Keypad Wake-Up (Voltage Regulator Power-Up)
+
+config PM_BFIN_WAKE_ROTARY
+ bool "Allow Wake-Up from on-chip Rotary"
+ depends on PM && BF54x
+ default n
+ help
+ Enable Rotary Wake-Up (Voltage Regulator Power-Up)
+
endmenu
menu "CPU Frequency scaling"