[AVR32] Wire up SSC platform device 0 as TX on ATSTK1000 board

[pandora-kernel.git] / arch / avr32 / boards / atstk1000 / atstk1002.c

diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c
index d47e39f..ed28304 100644 (file)
--- a/arch/avr32/boards/atstk1000/atstk1002.c
+++ b/arch/avr32/boards/atstk1000/atstk1002.c
@@ -8,7 +8,6 @@
  * published by the Free Software Foundation.
  */
 #include <linux/clk.h>
-#include <linux/device.h>
 #include <linux/etherdevice.h>
 #include <linux/init.h>
 #include <linux/kernel.h>
@@ -17,6 +16,8 @@
 #include <linux/types.h>
 #include <linux/spi/spi.h>
 
+#include <video/atmel_lcdc.h>
+
 #include <asm/io.h>
 #include <asm/setup.h>
 #include <asm/arch/at32ap7000.h>
@@ -24,27 +25,33 @@
 #include <asm/arch/init.h>
 #include <asm/arch/portmux.h>
 
+#include "atstk1000.h"
 
-#define        SW2_DEFAULT             /* MMCI and UART_A available */
 
 struct eth_addr {
        u8 addr[6];
 };
 
 static struct eth_addr __initdata hw_addr[2];
-
 static struct eth_platform_data __initdata eth_data[2];
-extern struct lcdc_platform_data atstk1000_fb0_data;
 
-static struct spi_board_info spi_board_info[] __initdata = {
+#ifndef CONFIG_BOARD_ATSTK1002_SW1_CUSTOM
+static struct spi_board_info spi0_board_info[] __initdata = {
        {
+               /* QVGA display */
                .modalias       = "ltv350qv",
-               .controller_data = (void *)GPIO_PIN_PA(4),
                .max_speed_hz   = 16000000,
-               .bus_num        = 0,
                .chip_select    = 1,
+               .mode           = SPI_MODE_3,
        },
 };
+#endif
+
+#ifdef CONFIG_BOARD_ATSTK1002_SPI1
+static struct spi_board_info spi1_board_info[] __initdata = { {
+       /* patch in custom entries here */
+} };
+#endif
 
 /*
  * The next two functions should go away as the boot loader is
@@ -103,10 +110,10 @@ static void __init set_hw_addr(struct platform_device *pdev)
 
 void __init setup_board(void)
 {
-#ifdef SW2_DEFAULT
-       at32_map_usart(1, 0);   /* USART 1/A: /dev/ttyS0, DB9 */
-#else
+#ifdef CONFIG_BOARD_ATSTK1002_SW2_CUSTOM
        at32_map_usart(0, 1);   /* USART 0/B: /dev/ttyS1, IRDA */
+#else
+       at32_map_usart(1, 0);   /* USART 1/A: /dev/ttyS0, DB9 */
 #endif
        /* USART 2/unused: expansion connector */
        at32_map_usart(3, 2);   /* USART 3/C: /dev/ttyS2, DB9 */
@@ -140,18 +147,30 @@ static int __init atstk1002_init(void)
 
        at32_add_system_devices();
 
-#ifdef SW2_DEFAULT
-       at32_add_device_usart(0);
-#else
+#ifdef CONFIG_BOARD_ATSTK1002_SW2_CUSTOM
        at32_add_device_usart(1);
+#else
+       at32_add_device_usart(0);
 #endif
        at32_add_device_usart(2);
 
        set_hw_addr(at32_add_device_eth(0, &eth_data[0]));
 
-       spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
-       at32_add_device_spi(0);
-       at32_add_device_lcdc(0, &atstk1000_fb0_data);
+#ifndef CONFIG_BOARD_ATSTK1002_SW1_CUSTOM
+       at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info));
+#endif
+#ifdef CONFIG_BOARD_ATSTK1002_SPI1
+       at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info));
+#endif
+#ifdef CONFIG_BOARD_ATSTK1002_SW5_CUSTOM
+       set_hw_addr(at32_add_device_eth(1, &eth_data[1]));
+#else
+       at32_add_device_lcdc(0, &atstk1000_lcdc_data,
+                            fbmem_start, fbmem_size);
+#endif
+#ifndef CONFIG_BOARD_ATSTK1002_SW3_CUSTOM
+       at32_add_device_ssc(0, ATMEL_SSC_TX);
+#endif
 
        return 0;
 }