#include <linux/amba/pl022.h>
#include <linux/spi/spi.h>
#include <linux/mfd/ab8500.h>
-#include <linux/mfd/tc35892.h>
-#include <linux/input/matrix_keypad.h>
+#include <linux/mfd/tc3589x.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <plat/pincfg.h>
#include <plat/i2c.h>
-#include <plat/ske.h>
#include <mach/hardware.h>
#include <mach/setup.h>
GPIO167_KP_O1,
GPIO168_KP_O0,
- GPIO217_GPIO, /* GPIO_EXP_INT */
-};
+ /* GPIO_EXP_INT */
+ GPIO217_GPIO,
-static void ab4500_spi_cs_control(u32 command)
-{
- /* set the FRM signal, which is CS - TODO */
-}
-
-struct pl022_config_chip ab4500_chip_info = {
- .com_mode = INTERRUPT_TRANSFER,
- .iface = SSP_INTERFACE_MOTOROLA_SPI,
- /* we can act as master only */
- .hierarchy = SSP_MASTER,
- .slave_tx_disable = 0,
- .rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
- .tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
- .cs_control = ab4500_spi_cs_control,
+ /* STMPE1601 IRQ */
+ GPIO218_GPIO | PIN_INPUT_PULLUP,
};
static struct ab8500_platform_data ab8500_platdata = {
static struct resource ab8500_resources[] = {
[0] = {
- .start = IRQ_AB8500,
- .end = IRQ_AB8500,
- .flags = IORESOURCE_IRQ
+ .start = IRQ_DB8500_AB8500,
+ .end = IRQ_DB8500_AB8500,
+ .flags = IORESOURCE_IRQ
}
};
.resource = ab8500_resources,
};
-static struct spi_board_info ab8500_spi_devices[] = {
- {
- .modalias = "ab8500-spi",
- .controller_data = &ab4500_chip_info,
- .platform_data = &ab8500_platdata,
- .max_speed_hz = 12000000,
- .bus_num = 0,
- .chip_select = 0,
- .mode = SPI_MODE_3,
- .irq = IRQ_DB8500_AB8500,
- },
-};
-
static struct pl022_ssp_controller ssp0_platform_data = {
.bus_id = 0,
/* pl022 not yet supports dma */
* TC35892
*/
-static void mop500_tc35892_init(struct tc35892 *tc35892, unsigned int base)
+static void mop500_tc35892_init(struct tc3589x *tc3589x, unsigned int base)
{
mop500_sdi_tc35892_init();
}
-static struct tc35892_gpio_platform_data mop500_tc35892_gpio_data = {
+static struct tc3589x_gpio_platform_data mop500_tc35892_gpio_data = {
.gpio_base = MOP500_EGPIO(0),
.setup = mop500_tc35892_init,
};
-static struct tc35892_platform_data mop500_tc35892_data = {
+static struct tc3589x_platform_data mop500_tc35892_data = {
+ .block = TC3589x_BLOCK_GPIO,
.gpio = &mop500_tc35892_gpio_data,
.irq_base = MOP500_EGPIO_IRQ_BASE,
};
static struct i2c_board_info mop500_i2c0_devices[] = {
{
- I2C_BOARD_INFO("tc35892", 0x42),
+ I2C_BOARD_INFO("tc3589x", 0x42),
.irq = NOMADIK_GPIO_TO_IRQ(217),
.platform_data = &mop500_tc35892_data,
},
db8500_add_i2c3(&u8500_i2c3_data);
}
-static const unsigned int ux500_keymap[] = {
- KEY(2, 5, KEY_END),
- KEY(4, 1, KEY_POWER),
- KEY(3, 5, KEY_VOLUMEDOWN),
- KEY(1, 3, KEY_3),
- KEY(5, 2, KEY_RIGHT),
- KEY(5, 0, KEY_9),
-
- KEY(0, 5, KEY_MENU),
- KEY(7, 6, KEY_ENTER),
- KEY(4, 5, KEY_0),
- KEY(6, 7, KEY_2),
- KEY(3, 4, KEY_UP),
- KEY(3, 3, KEY_DOWN),
-
- KEY(6, 4, KEY_SEND),
- KEY(6, 2, KEY_BACK),
- KEY(4, 2, KEY_VOLUMEUP),
- KEY(5, 5, KEY_1),
- KEY(4, 3, KEY_LEFT),
- KEY(3, 2, KEY_7),
-};
-
-static const struct matrix_keymap_data ux500_keymap_data = {
- .keymap = ux500_keymap,
- .keymap_size = ARRAY_SIZE(ux500_keymap),
-};
-
-/*
- * Nomadik SKE keypad
- */
-#define ROW_PIN_I0 164
-#define ROW_PIN_I1 163
-#define ROW_PIN_I2 162
-#define ROW_PIN_I3 161
-#define ROW_PIN_I4 156
-#define ROW_PIN_I5 155
-#define ROW_PIN_I6 154
-#define ROW_PIN_I7 153
-#define COL_PIN_O0 168
-#define COL_PIN_O1 167
-#define COL_PIN_O2 166
-#define COL_PIN_O3 165
-#define COL_PIN_O4 160
-#define COL_PIN_O5 159
-#define COL_PIN_O6 158
-#define COL_PIN_O7 157
-
-#define SKE_KPD_MAX_ROWS 8
-#define SKE_KPD_MAX_COLS 8
-
-static int ske_kp_rows[] = {
- ROW_PIN_I0, ROW_PIN_I1, ROW_PIN_I2, ROW_PIN_I3,
- ROW_PIN_I4, ROW_PIN_I5, ROW_PIN_I6, ROW_PIN_I7,
-};
-
-/*
- * ske_set_gpio_row: request and set gpio rows
- */
-static int ske_set_gpio_row(int gpio)
-{
- int ret;
-
- ret = gpio_request(gpio, "ske-kp");
- if (ret < 0) {
- pr_err("ske_set_gpio_row: gpio request failed\n");
- return ret;
- }
-
- ret = gpio_direction_output(gpio, 1);
- if (ret < 0) {
- pr_err("ske_set_gpio_row: gpio direction failed\n");
- gpio_free(gpio);
- }
-
- return ret;
-}
-
-/*
- * ske_kp_init - enable the gpio configuration
- */
-static int ske_kp_init(void)
-{
- int ret, i;
-
- for (i = 0; i < SKE_KPD_MAX_ROWS; i++) {
- ret = ske_set_gpio_row(ske_kp_rows[i]);
- if (ret < 0) {
- pr_err("ske_kp_init: failed init\n");
- return ret;
- }
- }
-
- return 0;
-}
-
-static struct ske_keypad_platform_data ske_keypad_board = {
- .init = ske_kp_init,
- .keymap_data = &ux500_keymap_data,
- .no_autorepeat = true,
- .krow = SKE_KPD_MAX_ROWS, /* 8x8 matrix */
- .kcol = SKE_KPD_MAX_COLS,
- .debounce_ms = 40, /* in millsecs */
-};
-
-
-
/* add any platform devices here - TODO */
static struct platform_device *platform_devs[] __initdata = {
- &ux500_ske_keypad_device,
};
static void __init mop500_spi_init(void)
nmk_config_pins(mop500_pins, ARRAY_SIZE(mop500_pins));
- ux500_ske_keypad_device.dev.platform_data = &ske_keypad_board;
platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs));
mop500_i2c_init();
mop500_spi_init();
mop500_uart_init();
- /* If HW is early drop (ED) or V1.0 then use SPI to access AB8500 */
- if (cpu_is_u8500ed() || cpu_is_u8500v10())
- spi_register_board_info(ab8500_spi_devices,
- ARRAY_SIZE(ab8500_spi_devices));
- else /* If HW is v.1.1 or later use I2C to access AB8500 */
- platform_device_register(&ab8500_device);
+ mop500_keypad_init();
+
+ platform_device_register(&ab8500_device);
i2c_register_board_info(0, mop500_i2c0_devices,
ARRAY_SIZE(mop500_i2c0_devices));