#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/gpio_keys.h>
+#include <linux/regulator/driver.h>
#include <linux/pinctrl/machine.h>
#include <linux/regulator/fixed.h>
+#include <linux/regulator/gpio-regulator.h>
#include <linux/regulator/machine.h>
#include <linux/sh_eth.h>
#include <linux/videodev2.h>
},
};
-/* Fixed 3.3V regulator to be used by SDHI0, SDHI1, MMCIF */
-static struct regulator_consumer_supply fixed3v3_power_consumers[] =
-{
+/* Fixed 3.3V regulator to be used by SDHI1, MMCIF */
+static struct regulator_consumer_supply fixed3v3_power_consumers[] = {
+ REGULATOR_SUPPLY("vmmc", "sh_mmcif"),
+ REGULATOR_SUPPLY("vqmmc", "sh_mmcif"),
+};
+
+/* Fixed 3.3V regulator to be used by SDHI0 */
+static struct regulator_consumer_supply vcc_sdhi0_consumers[] = {
REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+};
+
+static struct regulator_init_data vcc_sdhi0_init_data = {
+ .constraints = {
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(vcc_sdhi0_consumers),
+ .consumer_supplies = vcc_sdhi0_consumers,
+};
+
+static struct fixed_voltage_config vcc_sdhi0_info = {
+ .supply_name = "SDHI0 Vcc",
+ .microvolts = 3300000,
+ .gpio = GPIO_PORT75,
+ .enable_high = 1,
+ .init_data = &vcc_sdhi0_init_data,
+};
+
+static struct platform_device vcc_sdhi0 = {
+ .name = "reg-fixed-voltage",
+ .id = 1,
+ .dev = {
+ .platform_data = &vcc_sdhi0_info,
+ },
+};
+
+/* 1.8 / 3.3V SDHI0 VccQ regulator */
+static struct regulator_consumer_supply vccq_sdhi0_consumers[] = {
REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
+};
+
+static struct regulator_init_data vccq_sdhi0_init_data = {
+ .constraints = {
+ .input_uV = 3300000,
+ .min_uV = 1800000,
+ .max_uV = 3300000,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
+ REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(vccq_sdhi0_consumers),
+ .consumer_supplies = vccq_sdhi0_consumers,
+};
+
+static struct gpio vccq_sdhi0_gpios[] = {
+ {GPIO_PORT17, GPIOF_OUT_INIT_LOW, "vccq-sdhi0" },
+};
+
+static struct gpio_regulator_state vccq_sdhi0_states[] = {
+ { .value = 3300000, .gpios = (0 << 0) },
+ { .value = 1800000, .gpios = (1 << 0) },
+};
+
+static struct gpio_regulator_config vccq_sdhi0_info = {
+ .supply_name = "vqmmc",
+
+ .enable_gpio = GPIO_PORT74,
+ .enable_high = 1,
+ .enabled_at_boot = 0,
+
+ .gpios = vccq_sdhi0_gpios,
+ .nr_gpios = ARRAY_SIZE(vccq_sdhi0_gpios),
+
+ .states = vccq_sdhi0_states,
+ .nr_states = ARRAY_SIZE(vccq_sdhi0_states),
+
+ .type = REGULATOR_VOLTAGE,
+ .init_data = &vccq_sdhi0_init_data,
+};
+
+static struct platform_device vccq_sdhi0 = {
+ .name = "gpio-regulator",
+ .id = -1,
+ .dev = {
+ .platform_data = &vccq_sdhi0_info,
+ },
+};
+
+/* Fixed 3.3V regulator to be used by SDHI1 */
+static struct regulator_consumer_supply vcc_sdhi1_consumers[] = {
REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
- REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.1"),
- REGULATOR_SUPPLY("vmmc", "sh_mmcif"),
- REGULATOR_SUPPLY("vqmmc", "sh_mmcif"),
+};
+
+static struct regulator_init_data vcc_sdhi1_init_data = {
+ .constraints = {
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(vcc_sdhi1_consumers),
+ .consumer_supplies = vcc_sdhi1_consumers,
+};
+
+static struct fixed_voltage_config vcc_sdhi1_info = {
+ .supply_name = "SDHI1 Vcc",
+ .microvolts = 3300000,
+ .gpio = GPIO_PORT16,
+ .enable_high = 1,
+ .init_data = &vcc_sdhi1_init_data,
+};
+
+static struct platform_device vcc_sdhi1 = {
+ .name = "reg-fixed-voltage",
+ .id = 2,
+ .dev = {
+ .platform_data = &vcc_sdhi1_info,
+ },
};
/* SDHI0 */
static struct sh_mobile_sdhi_info sdhi0_info = {
.dma_slave_tx = SHDMA_SLAVE_SDHI0_TX,
.dma_slave_rx = SHDMA_SLAVE_SDHI0_RX,
- .tmio_caps = MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ |\
- MMC_CAP_NEEDS_POLL,
- .tmio_ocr_mask = MMC_VDD_165_195 | MMC_VDD_32_33 | MMC_VDD_33_34,
- .tmio_flags = TMIO_MMC_HAS_IDLE_WAIT,
+ .tmio_caps = MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ |
+ MMC_CAP_POWER_OFF_CARD,
+ .tmio_flags = TMIO_MMC_HAS_IDLE_WAIT | TMIO_MMC_USE_GPIO_CD,
+ .cd_gpio = GPIO_PORT167,
};
static struct resource sdhi0_resources[] = {
static struct sh_mobile_sdhi_info sdhi1_info = {
.dma_slave_tx = SHDMA_SLAVE_SDHI1_TX,
.dma_slave_rx = SHDMA_SLAVE_SDHI1_RX,
- .tmio_caps = MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ,
- .tmio_ocr_mask = MMC_VDD_165_195 | MMC_VDD_32_33 | MMC_VDD_33_34,
- .tmio_flags = TMIO_MMC_HAS_IDLE_WAIT,
+ .tmio_caps = MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ |
+ MMC_CAP_POWER_OFF_CARD,
+ .tmio_flags = TMIO_MMC_HAS_IDLE_WAIT | TMIO_MMC_USE_GPIO_CD,
+ /* Port72 cannot generate IRQs, will be used in polling mode. */
+ .cd_gpio = GPIO_PORT72,
};
static struct resource sdhi1_resources[] = {
/* MMCIF */
static struct sh_mmcif_plat_data sh_mmcif_plat = {
.sup_pclk = 0,
- .ocr = MMC_VDD_165_195 | MMC_VDD_32_33 | MMC_VDD_33_34,
.caps = MMC_CAP_4_BIT_DATA |
MMC_CAP_8_BIT_DATA |
MMC_CAP_NONREMOVABLE,
&lcdc0_device,
&gpio_keys_device,
&sh_eth_device,
+ &vcc_sdhi0,
+ &vccq_sdhi0,
&sdhi0_device,
&sh_mmcif_device,
&hdmi_device,
usb = &usbhsf_device;
}
- /* SDHI0 */
- gpio_request_one(17, GPIOF_OUT_INIT_LOW, NULL); /* SDHI0_18/33_B */
- gpio_request_one(74, GPIOF_OUT_INIT_HIGH, NULL); /* SDHI0_PON */
- gpio_request_one(75, GPIOF_OUT_INIT_HIGH, NULL); /* SDSLOT1_PON */
-
- /* we can use GPIO_FN_IRQ31_PORT167 here for SDHI0 CD irq */
-
/* CEU0 */
gpio_request(GPIO_FN_VIO0_D7, NULL);
gpio_request(GPIO_FN_VIO0_D6, NULL);
pinctrl_register_mappings(eva_sdhi1_pinctrl_map,
ARRAY_SIZE(eva_sdhi1_pinctrl_map));
- /* SDSLOT2_PON */
- gpio_request_one(16, GPIOF_OUT_INIT_HIGH, NULL);
-
+ platform_device_register(&vcc_sdhi1);
platform_device_register(&sdhi1_device);
}
git.openpandora.org / pandora-kernel.git / blobdiff