#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
-#include <linux/mmc/host.h>
#include <linux/mmc/sh_mmcif.h>
#include <linux/i2c.h>
#include <linux/i2c/tsc2007.h>
#include <linux/input/sh_keysc.h>
#include <linux/usb/r8a66597.h>
+#include <media/sh_mobile_ceu.h>
+#include <media/sh_mobile_csi2.h>
+#include <media/soc_camera.h>
+
#include <sound/sh_fsi.h>
#include <video/sh_mobile_hdmi.h>
.name = "loader",
.offset = 0x00000000,
.size = 512 * 1024,
+ .mask_flags = MTD_WRITEABLE,
},
{
.name = "bootenv",
.offset = MTDPART_OFS_APPEND,
.size = 512 * 1024,
+ .mask_flags = MTD_WRITEABLE,
},
{
.name = "kernel_ro",
},
};
+/*
+ * The card detect pin of the top SD/MMC slot (CN7) is active low and is
+ * connected to GPIO A22 of SH7372 (GPIO_PORT41).
+ */
+static int slot_cn7_get_cd(struct platform_device *pdev)
+{
+ if (gpio_is_valid(GPIO_PORT41))
+ return !gpio_get_value(GPIO_PORT41);
+ else
+ return -ENXIO;
+}
+
/* SH_MMCIF */
static struct resource sh_mmcif_resources[] = {
[0] = {
- .name = "SH_MMCIF",
+ .name = "MMCIF",
.start = 0xE6BD0000,
.end = 0xE6BD00FF,
.flags = IORESOURCE_MEM,
.caps = MMC_CAP_4_BIT_DATA |
MMC_CAP_8_BIT_DATA |
MMC_CAP_NEEDS_POLL,
+ .get_cd = slot_cn7_get_cd,
};
static struct platform_device sh_mmcif_device = {
.dma_slave_rx = SHDMA_SLAVE_SDHI1_RX,
.tmio_ocr_mask = MMC_VDD_165_195,
.tmio_flags = TMIO_MMC_WRPROTECT_DISABLE,
+ .tmio_caps = MMC_CAP_NEEDS_POLL,
+ .get_cd = slot_cn7_get_cd,
};
static struct resource sdhi1_resources[] = {
.resource = usb1_host_resources,
};
+const static struct fb_videomode ap4evb_lcdc_modes[] = {
+ {
+#ifdef CONFIG_AP4EVB_QHD
+ .name = "R63302(QHD)",
+ .xres = 544,
+ .yres = 961,
+ .left_margin = 72,
+ .right_margin = 600,
+ .hsync_len = 16,
+ .upper_margin = 8,
+ .lower_margin = 8,
+ .vsync_len = 2,
+ .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_HOR_HIGH_ACT,
+#else
+ .name = "WVGA Panel",
+ .xres = 800,
+ .yres = 480,
+ .left_margin = 220,
+ .right_margin = 110,
+ .hsync_len = 70,
+ .upper_margin = 20,
+ .lower_margin = 5,
+ .vsync_len = 5,
+ .sync = 0,
+#endif
+ },
+};
+
static struct sh_mobile_lcdc_info lcdc_info = {
.ch[0] = {
.chan = LCDC_CHAN_MAINLCD,
.bpp = 16,
+ .lcd_cfg = ap4evb_lcdc_modes,
+ .num_cfg = ARRAY_SIZE(ap4evb_lcdc_modes),
}
};
/* FSI */
#define IRQ_FSI evt2irq(0x1840)
-#define FSIACKCR 0xE6150018
-static void fsiackcr_init(struct clk *clk)
+
+static int fsi_set_rate(int is_porta, int rate)
{
- u32 status = __raw_readl(clk->enable_reg);
+ struct clk *fsib_clk;
+ struct clk *fdiv_clk = &sh7372_fsidivb_clk;
+ int ret;
- /* use external clock */
- status &= ~0x000000ff;
- status |= 0x00000080;
- __raw_writel(status, clk->enable_reg);
-}
+ /* set_rate is not needed if port A */
+ if (is_porta)
+ return 0;
+
+ fsib_clk = clk_get(NULL, "fsib_clk");
+ if (IS_ERR(fsib_clk))
+ return -EINVAL;
+
+ switch (rate) {
+ case 44100:
+ clk_set_rate(fsib_clk, clk_round_rate(fsib_clk, 11283000));
+ ret = SH_FSI_ACKMD_256 | SH_FSI_BPFMD_64;
+ break;
+ case 48000:
+ clk_set_rate(fsib_clk, clk_round_rate(fsib_clk, 85428000));
+ clk_set_rate(fdiv_clk, clk_round_rate(fdiv_clk, 12204000));
+ ret = SH_FSI_ACKMD_256 | SH_FSI_BPFMD_64;
+ break;
+ default:
+ pr_err("unsupported rate in FSI2 port B\n");
+ ret = -EINVAL;
+ break;
+ }
-static struct clk_ops fsiackcr_clk_ops = {
- .init = fsiackcr_init,
-};
+ clk_put(fsib_clk);
-static struct clk fsiackcr_clk = {
- .ops = &fsiackcr_clk_ops,
- .enable_reg = (void __iomem *)FSIACKCR,
- .rate = 0, /* unknown */
-};
+ return ret;
+}
static struct sh_fsi_platform_info fsi_info = {
.porta_flags = SH_FSI_BRS_INV |
SH_FSI_IN_SLAVE_MODE |
SH_FSI_OFMT(PCM) |
SH_FSI_IFMT(PCM),
+
+ .portb_flags = SH_FSI_BRS_INV |
+ SH_FSI_BRM_INV |
+ SH_FSI_LRS_INV |
+ SH_FSI_OFMT(SPDIF),
+ .set_rate = fsi_set_rate,
};
static struct resource fsi_resources[] = {
.interface_type = RGB24,
.clock_divider = 1,
.flags = LCDC_FLAGS_DWPOL,
- .lcd_cfg = {
- .name = "HDMI",
- /* So far only 720p is supported */
- .xres = 1280,
- .yres = 720,
- /*
- * If left and right margins are not multiples of 8,
- * LDHAJR will be adjusted accordingly by the LCDC
- * driver. Until we start using EDID, these values
- * might have to be adjusted for different monitors.
- */
- .left_margin = 200,
- .right_margin = 88,
- .hsync_len = 48,
- .upper_margin = 20,
- .lower_margin = 5,
- .vsync_len = 5,
- .pixclock = 13468,
- .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_HOR_HIGH_ACT,
- },
}
};
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = intcs_evt2irq(0x17a0),
+ .start = intcs_evt2irq(0x1780),
.flags = IORESOURCE_IRQ,
},
};
static struct sh_mobile_hdmi_info hdmi_info = {
.lcd_chan = &sh_mobile_lcdc1_info.ch[0],
.lcd_dev = &lcdc1_device.dev,
+ .flags = HDMI_SND_SRC_SPDIF,
};
static struct resource hdmi_resources[] = {
},
};
+static struct i2c_board_info imx074_info = {
+ I2C_BOARD_INFO("imx074", 0x1a),
+};
+
+struct soc_camera_link imx074_link = {
+ .bus_id = 0,
+ .board_info = &imx074_info,
+ .i2c_adapter_id = 0,
+ .module_name = "imx074",
+};
+
+static struct platform_device ap4evb_camera = {
+ .name = "soc-camera-pdrv",
+ .id = 0,
+ .dev = {
+ .platform_data = &imx074_link,
+ },
+};
+
+static struct sh_csi2_client_config csi2_clients[] = {
+ {
+ .phy = SH_CSI2_PHY_MAIN,
+ .lanes = 3,
+ .channel = 0,
+ .pdev = &ap4evb_camera,
+ },
+};
+
+static struct sh_csi2_pdata csi2_info = {
+ .type = SH_CSI2C,
+ .clients = csi2_clients,
+ .num_clients = ARRAY_SIZE(csi2_clients),
+ .flags = SH_CSI2_ECC | SH_CSI2_CRC,
+};
+
+static struct resource csi2_resources[] = {
+ [0] = {
+ .name = "CSI2",
+ .start = 0xffc90000,
+ .end = 0xffc90fff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = intcs_evt2irq(0x17a0),
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device csi2_device = {
+ .name = "sh-mobile-csi2",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(csi2_resources),
+ .resource = csi2_resources,
+ .dev = {
+ .platform_data = &csi2_info,
+ },
+};
+
+static struct sh_mobile_ceu_info sh_mobile_ceu_info = {
+ .flags = SH_CEU_FLAG_USE_8BIT_BUS,
+ .csi2_dev = &csi2_device.dev,
+};
+
+static struct resource ceu_resources[] = {
+ [0] = {
+ .name = "CEU",
+ .start = 0xfe910000,
+ .end = 0xfe91009f,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = intcs_evt2irq(0x880),
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ /* place holder for contiguous memory */
+ },
+};
+
+static struct platform_device ceu_device = {
+ .name = "sh_mobile_ceu",
+ .id = 0, /* "ceu0" clock */
+ .num_resources = ARRAY_SIZE(ceu_resources),
+ .resource = ceu_resources,
+ .dev = {
+ .platform_data = &sh_mobile_ceu_info,
+ },
+};
+
static struct platform_device *ap4evb_devices[] __initdata = {
&leds_device,
&nor_flash_device,
&lcdc1_device,
&lcdc_device,
&hdmi_device,
+ &csi2_device,
+ &ceu_device,
+ &ap4evb_camera,
};
static int __init hdmi_init_pm_clock(void)
goto out;
}
- ret = clk_set_parent(&pllc2_clk, &dv_clki_div2_clk);
+ ret = clk_set_parent(&sh7372_pllc2_clk, &sh7372_dv_clki_div2_clk);
if (ret < 0) {
- pr_err("Cannot set PLLC2 parent: %d, %d users\n", ret, pllc2_clk.usecount);
+ pr_err("Cannot set PLLC2 parent: %d, %d users\n", ret, sh7372_pllc2_clk.usecount);
goto out;
}
- pr_debug("PLLC2 initial frequency %lu\n", clk_get_rate(&pllc2_clk));
+ pr_debug("PLLC2 initial frequency %lu\n", clk_get_rate(&sh7372_pllc2_clk));
- rate = clk_round_rate(&pllc2_clk, 594000000);
+ rate = clk_round_rate(&sh7372_pllc2_clk, 594000000);
if (rate < 0) {
pr_err("Cannot get suitable rate: %ld\n", rate);
ret = rate;
goto out;
}
- ret = clk_set_rate(&pllc2_clk, rate);
+ ret = clk_set_rate(&sh7372_pllc2_clk, rate);
if (ret < 0) {
pr_err("Cannot set rate %ld: %d\n", rate, ret);
goto out;
pr_debug("PLLC2 set frequency %lu\n", rate);
- ret = clk_set_parent(hdmi_ick, &pllc2_clk);
+ ret = clk_set_parent(hdmi_ick, &sh7372_pllc2_clk);
if (ret < 0) {
pr_err("Cannot set HDMI parent: %d\n", ret);
goto out;
device_initcall(hdmi_init_pm_clock);
+#define FSIACK_DUMMY_RATE 48000
+static int __init fsi_init_pm_clock(void)
+{
+ struct clk *fsia_ick;
+ int ret;
+
+ /*
+ * FSIACK is connected to AK4642,
+ * and the rate is depend on playing sound rate.
+ * So, set dummy rate (= 48k) here
+ */
+ ret = clk_set_rate(&sh7372_fsiack_clk, FSIACK_DUMMY_RATE);
+ if (ret < 0) {
+ pr_err("Cannot set FSIACK dummy rate: %d\n", ret);
+ return ret;
+ }
+
+ fsia_ick = clk_get(&fsi_device.dev, "icka");
+ if (IS_ERR(fsia_ick)) {
+ ret = PTR_ERR(fsia_ick);
+ pr_err("Cannot get FSI ICK: %d\n", ret);
+ return ret;
+ }
+
+ ret = clk_set_parent(fsia_ick, &sh7372_fsiack_clk);
+ if (ret < 0) {
+ pr_err("Cannot set FSI-A parent: %d\n", ret);
+ goto out;
+ }
+
+ ret = clk_set_rate(fsia_ick, FSIACK_DUMMY_RATE);
+ if (ret < 0)
+ pr_err("Cannot set FSI-A rate: %d\n", ret);
+
+out:
+ clk_put(fsia_ick);
+
+ return ret;
+}
+device_initcall(fsi_init_pm_clock);
+
/*
* FIXME !!
*
* gpio_no_direction
- * gpio_pull_up
* are quick_hack.
*
* current gpio frame work doesn't have
__raw_writeb(0x00, addr);
}
-static void __init gpio_pull_up(u32 addr)
-{
- u8 data = __raw_readb(addr);
-
- data &= 0x0F;
- data |= 0xC0;
- __raw_writeb(data, addr);
-}
-
/* TouchScreen */
+#ifdef CONFIG_AP4EVB_QHD
+# define GPIO_TSC_IRQ GPIO_FN_IRQ28_123
+# define GPIO_TSC_PORT GPIO_PORT123
+#else /* WVGA */
+# define GPIO_TSC_IRQ GPIO_FN_IRQ7_40
+# define GPIO_TSC_PORT GPIO_PORT40
+#endif
+
#define IRQ28 evt2irq(0x3380) /* IRQ28A */
#define IRQ7 evt2irq(0x02e0) /* IRQ7A */
static int ts_get_pendown_state(void)
{
- int val1, val2;
+ int val;
- gpio_free(GPIO_FN_IRQ28_123);
- gpio_free(GPIO_FN_IRQ7_40);
+ gpio_free(GPIO_TSC_IRQ);
- gpio_request(GPIO_PORT123, NULL);
- gpio_request(GPIO_PORT40, NULL);
+ gpio_request(GPIO_TSC_PORT, NULL);
- gpio_direction_input(GPIO_PORT123);
- gpio_direction_input(GPIO_PORT40);
+ gpio_direction_input(GPIO_TSC_PORT);
- val1 = gpio_get_value(GPIO_PORT123);
- val2 = gpio_get_value(GPIO_PORT40);
+ val = gpio_get_value(GPIO_TSC_PORT);
- gpio_request(GPIO_FN_IRQ28_123, NULL); /* for QHD */
- gpio_request(GPIO_FN_IRQ7_40, NULL); /* for WVGA */
+ gpio_request(GPIO_TSC_IRQ, NULL);
- return val1 ^ val2;
+ return !val;
}
-#define PORT40CR 0xE6051028
-#define PORT123CR 0xE605007B
static int ts_init(void)
{
- gpio_request(GPIO_FN_IRQ28_123, NULL); /* for QHD */
- gpio_request(GPIO_FN_IRQ7_40, NULL); /* for WVGA */
-
- gpio_pull_up(PORT40CR);
- gpio_pull_up(PORT123CR);
+ gpio_request(GPIO_TSC_IRQ, NULL);
return 0;
}
#define GPIO_PORT9CR 0xE6051009
#define GPIO_PORT10CR 0xE605100A
+#define USCCR1 0xE6058144
static void __init ap4evb_init(void)
{
u32 srcr4;
/* setup USB phy */
__raw_writew(0x8a0a, 0xE6058130); /* USBCR2 */
- /* enable FSI2 */
+ /* enable FSI2 port A (ak4643) */
gpio_request(GPIO_FN_FSIAIBT, NULL);
gpio_request(GPIO_FN_FSIAILR, NULL);
gpio_request(GPIO_FN_FSIAISLD, NULL);
gpio_no_direction(GPIO_PORT9CR); /* FSIAOBT needs no direction */
gpio_no_direction(GPIO_PORT10CR); /* FSIAOLR needs no direction */
+ /* card detect pin for MMC slot (CN7) */
+ gpio_request(GPIO_PORT41, NULL);
+ gpio_direction_input(GPIO_PORT41);
+
+ /* setup FSI2 port B (HDMI) */
+ gpio_request(GPIO_FN_FSIBCK, NULL);
+ __raw_writew(__raw_readw(USCCR1) & ~(1 << 6), USCCR1); /* use SPDIF */
+
/* set SPU2 clock to 119.6 MHz */
clk = clk_get(NULL, "spu_clk");
if (!IS_ERR(clk)) {
clk_put(clk);
}
- /* change parent of FSI A */
- clk = clk_get(NULL, "fsia_clk");
- if (!IS_ERR(clk)) {
- clk_register(&fsiackcr_clk);
- clk_set_parent(clk, &fsiackcr_clk);
- clk_put(clk);
- }
-
/*
* set irq priority, to avoid sound chopping
* when NFS rootfs is used
ARRAY_SIZE(i2c1_devices));
#ifdef CONFIG_AP4EVB_QHD
+
/*
- * QHD
+ * For QHD Panel (MIPI-DSI, CONFIG_AP4EVB_QHD=y) and
+ * IRQ28 for Touch Panel, set dip switches S3, S43 as OFF, ON.
*/
/* enable KEYSC */
lcdc_info.ch[0].interface_type = RGB24;
lcdc_info.ch[0].clock_divider = 1;
lcdc_info.ch[0].flags = LCDC_FLAGS_DWPOL;
- lcdc_info.ch[0].lcd_cfg.name = "R63302(QHD)";
- lcdc_info.ch[0].lcd_cfg.xres = 544;
- lcdc_info.ch[0].lcd_cfg.yres = 961;
- lcdc_info.ch[0].lcd_cfg.left_margin = 72;
- lcdc_info.ch[0].lcd_cfg.right_margin = 600;
- lcdc_info.ch[0].lcd_cfg.hsync_len = 16;
- lcdc_info.ch[0].lcd_cfg.upper_margin = 8;
- lcdc_info.ch[0].lcd_cfg.lower_margin = 8;
- lcdc_info.ch[0].lcd_cfg.vsync_len = 2;
- lcdc_info.ch[0].lcd_cfg.sync = FB_SYNC_VERT_HIGH_ACT |
- FB_SYNC_HOR_HIGH_ACT;
lcdc_info.ch[0].lcd_size_cfg.width = 44;
lcdc_info.ch[0].lcd_size_cfg.height = 79;
#else
/*
- * WVGA
+ * For WVGA Panel (18-bit RGB, CONFIG_AP4EVB_WVGA=y) and
+ * IRQ7 for Touch Panel, set dip switches S3, S43 to ON, OFF.
*/
+
gpio_request(GPIO_FN_LCDD17, NULL);
gpio_request(GPIO_FN_LCDD16, NULL);
gpio_request(GPIO_FN_LCDD15, NULL);
lcdc_info.ch[0].interface_type = RGB18;
lcdc_info.ch[0].clock_divider = 2;
lcdc_info.ch[0].flags = 0;
- lcdc_info.ch[0].lcd_cfg.name = "WVGA Panel";
- lcdc_info.ch[0].lcd_cfg.xres = 800;
- lcdc_info.ch[0].lcd_cfg.yres = 480;
- lcdc_info.ch[0].lcd_cfg.left_margin = 220;
- lcdc_info.ch[0].lcd_cfg.right_margin = 110;
- lcdc_info.ch[0].lcd_cfg.hsync_len = 70;
- lcdc_info.ch[0].lcd_cfg.upper_margin = 20;
- lcdc_info.ch[0].lcd_cfg.lower_margin = 5;
- lcdc_info.ch[0].lcd_cfg.vsync_len = 5;
- lcdc_info.ch[0].lcd_cfg.sync = 0;
lcdc_info.ch[0].lcd_size_cfg.width = 152;
lcdc_info.ch[0].lcd_size_cfg.height = 91;
i2c_register_board_info(0, &tsc_device, 1);
#endif /* CONFIG_AP4EVB_QHD */
+ /* CEU */
+
+ /*
+ * TODO: reserve memory for V4L2 DMA buffers, when a suitable API
+ * becomes available
+ */
+
+ /* MIPI-CSI stuff */
+ gpio_request(GPIO_FN_VIO_CKO, NULL);
+
+ clk = clk_get(NULL, "vck1_clk");
+ if (!IS_ERR(clk)) {
+ clk_set_rate(clk, clk_round_rate(clk, 13000000));
+ clk_enable(clk);
+ clk_put(clk);
+ }
+
sh7372_add_standard_devices();
/* HDMI */
shmobile_timer.init();
/* External clock source */
- clk_set_rate(&dv_clki_clk, 27000000);
+ clk_set_rate(&sh7372_dv_clki_clk, 27000000);
}
static struct sys_timer ap4evb_timer = {
git.openpandora.org / pandora-kernel.git / blobdiff