#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/mfd/sh_mobile_sdhi.h>
+#include <linux/mmc/host.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
#include <sound/sh_fsi.h>
+#include <video/sh_mobile_hdmi.h>
#include <video/sh_mobile_lcdc.h>
#include <video/sh_mipi_dsi.h>
/*
* LCD / IRQ / KEYSC / IrDA
*
- * IRQ = IRQ26 (TS), IRQ27 (VIO), IRQ28 (TouchScreen)
- * LCD = 2nd LCDC
+ * IRQ = IRQ26 (TS), IRQ27 (VIO), IRQ28 (QHD-TouchScreen)
+ * LCD = 2nd LCDC (WVGA)
*
* | SW43 |
* SW3 | ON | OFF |
* -------------+-----------------------+---------------+
* ON | KEY / IrDA | LCD |
* OFF | KEY / IrDA / IRQ | IRQ |
+ *
+ *
+ * QHD / WVGA display
+ *
+ * You can choice display type on menuconfig.
+ * Then, check above dip-switch.
*/
/*
*/
/*
- * MMC (CN7)
+ * MMC0/SDHI1 (CN7)
+ *
+ * J22 : select card voltage
+ * 1-2 pin : 1.8v
+ * 2-3 pin : 3.3v
+ *
+ * SW1 | SW33
+ * | bit1 | bit2 | bit3 | bit4
+ * ------------+------+------+------+-------
+ * MMC0 OFF | OFF | ON | ON | X
+ * SDHI1 OFF | ON | X | OFF | ON
*
- * J22 : 1-2: 1.8v for MMC
- * 2-3: 3.3v for MMC
- * SW1 : OFF
- * SW33: bit1: OFF
- * bit2: ON
- * bit3: ON
- * bit4: X
+ * voltage lebel
+ * CN7 : 1.8v
+ * CN12: 3.3v
*/
/* MTD */
},
};
-/* KEYSC (Needs SW43 set to ON) */
-static struct sh_keysc_info keysc_info = {
- .mode = SH_KEYSC_MODE_1,
- .scan_timing = 3,
- .delay = 2500,
- .keycodes = {
- KEY_0, KEY_1, KEY_2, KEY_3, KEY_4,
- KEY_5, KEY_6, KEY_7, KEY_8, KEY_9,
- KEY_A, KEY_B, KEY_C, KEY_D, KEY_E,
- KEY_F, KEY_G, KEY_H, KEY_I, KEY_J,
- KEY_K, KEY_L, KEY_M, KEY_N, KEY_O,
- },
-};
-
-static struct resource keysc_resources[] = {
- [0] = {
- .name = "KEYSC",
- .start = 0xe61b0000,
- .end = 0xe61b0063,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = evt2irq(0x0be0), /* KEYSC_KEY */
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device keysc_device = {
- .name = "sh_keysc",
- .id = 0, /* "keysc0" clock */
- .num_resources = ARRAY_SIZE(keysc_resources),
- .resource = keysc_resources,
- .dev = {
- .platform_data = &keysc_info,
- },
-};
-
/* SH_MMCIF */
static struct resource sh_mmcif_resources[] = {
[0] = {
},
[1] = {
/* MMC ERR */
- .start = 198,
+ .start = evt2irq(0x1ac0),
.flags = IORESOURCE_IRQ,
},
[2] = {
/* MMC NOR */
- .start = 199,
+ .start = evt2irq(0x1ae0),
.flags = IORESOURCE_IRQ,
},
};
-struct sh_mmcif_plat_data sh_mmcif_plat = {
+static struct sh_mmcif_plat_data sh_mmcif_plat = {
.sup_pclk = 0,
.ocr = MMC_VDD_165_195 | MMC_VDD_32_33 | MMC_VDD_33_34,
.caps = MMC_CAP_4_BIT_DATA |
/* SDHI0 */
static struct sh_mobile_sdhi_info sdhi0_info = {
- .dma_slave_tx = SHDMA_SLAVE_SDHI0_TX,
- .dma_slave_rx = SHDMA_SLAVE_SDHI0_RX,
+ .dma_slave_tx = SHDMA_SLAVE_SDHI0_TX,
+ .dma_slave_rx = SHDMA_SLAVE_SDHI0_RX,
};
static struct resource sdhi0_resources[] = {
},
};
+/* SDHI1 */
+static struct sh_mobile_sdhi_info sdhi1_info = {
+ .dma_slave_tx = SHDMA_SLAVE_SDHI1_TX,
+ .dma_slave_rx = SHDMA_SLAVE_SDHI1_RX,
+ .tmio_ocr_mask = MMC_VDD_165_195,
+};
+
+static struct resource sdhi1_resources[] = {
+ [0] = {
+ .name = "SDHI1",
+ .start = 0xe6860000,
+ .end = 0xe68601ff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = evt2irq(0x0e80),
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device sdhi1_device = {
+ .name = "sh_mobile_sdhi",
+ .num_resources = ARRAY_SIZE(sdhi1_resources),
+ .resource = sdhi1_resources,
+ .id = 1,
+ .dev = {
+ .platform_data = &sdhi1_info,
+ },
+};
+
/* USB1 */
-void usb1_host_port_power(int port, int power)
+static void usb1_host_port_power(int port, int power)
{
if (!power) /* only power-on supported for now */
return;
.resource = usb1_host_resources,
};
-static struct sh_mobile_lcdc_info sh_mobile_lcdc_info = {
- .clock_source = LCDC_CLK_PERIPHERAL, /* One of interface clocks */
+static struct sh_mobile_lcdc_info lcdc_info = {
.ch[0] = {
.chan = LCDC_CHAN_MAINLCD,
.bpp = 16,
- .interface_type = RGB24,
- .clock_divider = 1,
- .flags = LCDC_FLAGS_DWPOL,
- .lcd_cfg = {
- .name = "R63302(QHD)",
- .xres = 544,
- .yres = 961,
- .left_margin = 72,
- .right_margin = 600,
- .hsync_len = 16,
- .upper_margin = 8,
- .lower_margin = 8,
- .vsync_len = 2,
- .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_HOR_HIGH_ACT,
- },
- .lcd_size_cfg = {
- .width = 44,
- .height = 79,
- },
}
};
.num_resources = ARRAY_SIZE(lcdc_resources),
.resource = lcdc_resources,
.dev = {
- .platform_data = &sh_mobile_lcdc_info,
+ .platform_data = &lcdc_info,
.coherent_dma_mask = ~0,
},
};
+/*
+ * QHD display
+ */
+#ifdef CONFIG_AP4EVB_QHD
+
+/* KEYSC (Needs SW43 set to ON) */
+static struct sh_keysc_info keysc_info = {
+ .mode = SH_KEYSC_MODE_1,
+ .scan_timing = 3,
+ .delay = 2500,
+ .keycodes = {
+ KEY_0, KEY_1, KEY_2, KEY_3, KEY_4,
+ KEY_5, KEY_6, KEY_7, KEY_8, KEY_9,
+ KEY_A, KEY_B, KEY_C, KEY_D, KEY_E,
+ KEY_F, KEY_G, KEY_H, KEY_I, KEY_J,
+ KEY_K, KEY_L, KEY_M, KEY_N, KEY_O,
+ },
+};
+
+static struct resource keysc_resources[] = {
+ [0] = {
+ .name = "KEYSC",
+ .start = 0xe61b0000,
+ .end = 0xe61b0063,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = evt2irq(0x0be0), /* KEYSC_KEY */
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device keysc_device = {
+ .name = "sh_keysc",
+ .id = 0, /* "keysc0" clock */
+ .num_resources = ARRAY_SIZE(keysc_resources),
+ .resource = keysc_resources,
+ .dev = {
+ .platform_data = &keysc_info,
+ },
+};
+
+/* MIPI-DSI */
static struct resource mipidsi0_resources[] = {
[0] = {
.start = 0xffc60000,
static struct sh_mipi_dsi_info mipidsi0_info = {
.data_format = MIPI_RGB888,
- .lcd_chan = &sh_mobile_lcdc_info.ch[0],
+ .lcd_chan = &lcdc_info.ch[0],
};
static struct platform_device mipidsi0_device = {
},
};
+/* This function will disappear when we switch to (runtime) PM */
+static int __init ap4evb_init_display_clk(void)
+{
+ struct clk *lcdc_clk;
+ struct clk *dsitx_clk;
+ int ret;
+
+ lcdc_clk = clk_get(&lcdc_device.dev, "sh_mobile_lcdc_fb.0");
+ if (IS_ERR(lcdc_clk))
+ return PTR_ERR(lcdc_clk);
+
+ dsitx_clk = clk_get(&mipidsi0_device.dev, "sh-mipi-dsi.0");
+ if (IS_ERR(dsitx_clk)) {
+ ret = PTR_ERR(dsitx_clk);
+ goto eclkdsitxget;
+ }
+
+ ret = clk_enable(lcdc_clk);
+ if (ret < 0)
+ goto eclklcdcon;
+
+ ret = clk_enable(dsitx_clk);
+ if (ret < 0)
+ goto eclkdsitxon;
+
+ return 0;
+
+eclkdsitxon:
+ clk_disable(lcdc_clk);
+eclklcdcon:
+ clk_put(dsitx_clk);
+eclkdsitxget:
+ clk_put(lcdc_clk);
+
+ return ret;
+}
+device_initcall(ap4evb_init_display_clk);
+
+static struct platform_device *qhd_devices[] __initdata = {
+ &mipidsi0_device,
+ &keysc_device,
+};
+#endif /* CONFIG_AP4EVB_QHD */
+
/* FSI */
#define IRQ_FSI evt2irq(0x1840)
#define FSIACKCR 0xE6150018
.rate = 0, /* unknown */
};
-struct sh_fsi_platform_info fsi_info = {
+static struct sh_fsi_platform_info fsi_info = {
.porta_flags = SH_FSI_BRS_INV |
SH_FSI_OUT_SLAVE_MODE |
SH_FSI_IN_SLAVE_MODE |
},
};
+static struct sh_mobile_lcdc_info sh_mobile_lcdc1_info = {
+ .clock_source = LCDC_CLK_EXTERNAL,
+ .ch[0] = {
+ .chan = LCDC_CHAN_MAINLCD,
+ .bpp = 16,
+ .interface_type = RGB24,
+ .clock_divider = 1,
+ .flags = LCDC_FLAGS_DWPOL,
+ .lcd_cfg = {
+ .name = "HDMI",
+ /* So far only 720p is supported */
+ .xres = 1280,
+ .yres = 720,
+ /*
+ * If left and right margins are not multiples of 8,
+ * LDHAJR will be adjusted accordingly by the LCDC
+ * driver. Until we start using EDID, these values
+ * might have to be adjusted for different monitors.
+ */
+ .left_margin = 200,
+ .right_margin = 88,
+ .hsync_len = 48,
+ .upper_margin = 20,
+ .lower_margin = 5,
+ .vsync_len = 5,
+ .pixclock = 13468,
+ .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_HOR_HIGH_ACT,
+ },
+ }
+};
+
+static struct resource lcdc1_resources[] = {
+ [0] = {
+ .name = "LCDC1",
+ .start = 0xfe944000,
+ .end = 0xfe947fff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = intcs_evt2irq(0x17a0),
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device lcdc1_device = {
+ .name = "sh_mobile_lcdc_fb",
+ .num_resources = ARRAY_SIZE(lcdc1_resources),
+ .resource = lcdc1_resources,
+ .id = 1,
+ .dev = {
+ .platform_data = &sh_mobile_lcdc1_info,
+ .coherent_dma_mask = ~0,
+ },
+};
+
+static struct sh_mobile_hdmi_info hdmi_info = {
+ .lcd_chan = &sh_mobile_lcdc1_info.ch[0],
+ .lcd_dev = &lcdc1_device.dev,
+};
+
+static struct resource hdmi_resources[] = {
+ [0] = {
+ .name = "HDMI",
+ .start = 0xe6be0000,
+ .end = 0xe6be00ff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ /* There's also an HDMI interrupt on INTCS @ 0x18e0 */
+ .start = evt2irq(0x17e0),
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device hdmi_device = {
+ .name = "sh-mobile-hdmi",
+ .num_resources = ARRAY_SIZE(hdmi_resources),
+ .resource = hdmi_resources,
+ .id = -1,
+ .dev = {
+ .platform_data = &hdmi_info,
+ },
+};
+
static struct platform_device *ap4evb_devices[] __initdata = {
&nor_flash_device,
&smc911x_device,
- &keysc_device,
&sdhi0_device,
+ &sdhi1_device,
&usb1_host_device,
- &lcdc_device,
- &mipidsi0_device,
&fsi_device,
- &sh_mmcif_device
+ &sh_mmcif_device,
+ &lcdc1_device,
+ &lcdc_device,
+ &hdmi_device,
};
-/* TouchScreen (Needs SW3 set to OFF) */
+static int __init hdmi_init_pm_clock(void)
+{
+ struct clk *hdmi_ick = clk_get(&hdmi_device.dev, "ick");
+ int ret;
+ long rate;
+
+ if (IS_ERR(hdmi_ick)) {
+ ret = PTR_ERR(hdmi_ick);
+ pr_err("Cannot get HDMI ICK: %d\n", ret);
+ goto out;
+ }
+
+ ret = clk_set_parent(&pllc2_clk, &dv_clki_div2_clk);
+ if (ret < 0) {
+ pr_err("Cannot set PLLC2 parent: %d, %d users\n", ret, pllc2_clk.usecount);
+ goto out;
+ }
+
+ pr_debug("PLLC2 initial frequency %lu\n", clk_get_rate(&pllc2_clk));
+
+ rate = clk_round_rate(&pllc2_clk, 594000000);
+ if (rate < 0) {
+ pr_err("Cannot get suitable rate: %ld\n", rate);
+ ret = rate;
+ goto out;
+ }
+
+ ret = clk_set_rate(&pllc2_clk, rate);
+ if (ret < 0) {
+ pr_err("Cannot set rate %ld: %d\n", rate, ret);
+ goto out;
+ }
+
+ pr_debug("PLLC2 set frequency %lu\n", rate);
+
+ ret = clk_set_parent(hdmi_ick, &pllc2_clk);
+ if (ret < 0) {
+ pr_err("Cannot set HDMI parent: %d\n", ret);
+ goto out;
+ }
+
+out:
+ if (!IS_ERR(hdmi_ick))
+ clk_put(hdmi_ick);
+ return ret;
+}
+
+device_initcall(hdmi_init_pm_clock);
+
+/*
+ * FIXME !!
+ *
+ * gpio_no_direction
+ * gpio_pull_up
+ * are quick_hack.
+ *
+ * current gpio frame work doesn't have
+ * the method to control only pull up/down/free.
+ * this function should be replaced by correct gpio function
+ */
+static void __init gpio_no_direction(u32 addr)
+{
+ __raw_writeb(0x00, addr);
+}
+
+static void __init gpio_pull_up(u32 addr)
+{
+ u8 data = __raw_readb(addr);
+
+ data &= 0x0F;
+ data |= 0xC0;
+ __raw_writeb(data, addr);
+}
+
+/* TouchScreen */
#define IRQ28 evt2irq(0x3380) /* IRQ28A */
-struct tsc2007_platform_data tsc2007_info = {
+#define IRQ7 evt2irq(0x02e0) /* IRQ7A */
+static int ts_get_pendown_state(void)
+{
+ int val1, val2;
+
+ gpio_free(GPIO_FN_IRQ28_123);
+ gpio_free(GPIO_FN_IRQ7_40);
+
+ gpio_request(GPIO_PORT123, NULL);
+ gpio_request(GPIO_PORT40, NULL);
+
+ gpio_direction_input(GPIO_PORT123);
+ gpio_direction_input(GPIO_PORT40);
+
+ val1 = gpio_get_value(GPIO_PORT123);
+ val2 = gpio_get_value(GPIO_PORT40);
+
+ gpio_request(GPIO_FN_IRQ28_123, NULL); /* for QHD */
+ gpio_request(GPIO_FN_IRQ7_40, NULL); /* for WVGA */
+
+ return val1 ^ val2;
+}
+
+#define PORT40CR 0xE6051028
+#define PORT123CR 0xE605007B
+static int ts_init(void)
+{
+ gpio_request(GPIO_FN_IRQ28_123, NULL); /* for QHD */
+ gpio_request(GPIO_FN_IRQ7_40, NULL); /* for WVGA */
+
+ gpio_pull_up(PORT40CR);
+ gpio_pull_up(PORT123CR);
+
+ return 0;
+}
+
+static struct tsc2007_platform_data tsc2007_info = {
.model = 2007,
.x_plate_ohms = 180,
+ .get_pendown_state = ts_get_pendown_state,
+ .init_platform_hw = ts_init,
+};
+
+static struct i2c_board_info tsc_device = {
+ I2C_BOARD_INFO("tsc2007", 0x48),
+ .type = "tsc2007",
+ .platform_data = &tsc2007_info,
+ /*.irq is selected on ap4evb_init */
};
/* I2C */
{
I2C_BOARD_INFO("r2025sd", 0x32),
},
- {
- I2C_BOARD_INFO("tsc2007", 0x48),
- .type = "tsc2007",
- .platform_data = &tsc2007_info,
- .irq = IRQ28,
- },
};
static struct map_desc ap4evb_io_desc[] __initdata = {
shmobile_setup_console();
}
-/* This function will disappear when we switch to (runtime) PM */
-static int __init ap4evb_init_display_clk(void)
-{
- struct clk *lcdc_clk;
- struct clk *dsitx_clk;
- int ret;
-
- lcdc_clk = clk_get(&lcdc_device.dev, "sh_mobile_lcdc_fb.0");
- if (IS_ERR(lcdc_clk))
- return PTR_ERR(lcdc_clk);
-
- dsitx_clk = clk_get(&mipidsi0_device.dev, "sh-mipi-dsi.0");
- if (IS_ERR(dsitx_clk)) {
- ret = PTR_ERR(dsitx_clk);
- goto eclkdsitxget;
- }
-
- ret = clk_enable(lcdc_clk);
- if (ret < 0)
- goto eclklcdcon;
-
- ret = clk_enable(dsitx_clk);
- if (ret < 0)
- goto eclkdsitxon;
-
- return 0;
-
-eclkdsitxon:
- clk_disable(lcdc_clk);
-eclklcdcon:
- clk_put(dsitx_clk);
-eclkdsitxget:
- clk_put(lcdc_clk);
-
- return ret;
-}
-
-device_initcall(ap4evb_init_display_clk);
-
-/*
- * FIXME !!
- *
- * gpio_no_direction is quick_hack.
- *
- * current gpio frame work doesn't have
- * the method to control only pull up/down/free.
- * this function should be replaced by correct gpio function
- */
-static void __init gpio_no_direction(u32 addr)
-{
- __raw_writeb(0x00, addr);
-}
-
#define GPIO_PORT9CR 0xE6051009
#define GPIO_PORT10CR 0xE605100A
-
static void __init ap4evb_init(void)
{
+ u32 srcr4;
struct clk *clk;
sh7372_pinmux_init();
gpio_export(GPIO_PORT34, 0);
gpio_export(GPIO_PORT35, 0);
- /* enable KEYSC */
- gpio_request(GPIO_FN_KEYOUT0, NULL);
- gpio_request(GPIO_FN_KEYOUT1, NULL);
- gpio_request(GPIO_FN_KEYOUT2, NULL);
- gpio_request(GPIO_FN_KEYOUT3, NULL);
- gpio_request(GPIO_FN_KEYOUT4, NULL);
- gpio_request(GPIO_FN_KEYIN0_136, NULL);
- gpio_request(GPIO_FN_KEYIN1_135, NULL);
- gpio_request(GPIO_FN_KEYIN2_134, NULL);
- gpio_request(GPIO_FN_KEYIN3_133, NULL);
- gpio_request(GPIO_FN_KEYIN4, NULL);
-
/* SDHI0 */
gpio_request(GPIO_FN_SDHICD0, NULL);
gpio_request(GPIO_FN_SDHIWP0, NULL);
gpio_request(GPIO_FN_SDHID0_1, NULL);
gpio_request(GPIO_FN_SDHID0_0, NULL);
- /* enable TouchScreen */
- gpio_request(GPIO_FN_IRQ28_123, NULL);
- set_irq_type(IRQ28, IRQ_TYPE_LEVEL_LOW);
+ /* SDHI1 */
+ gpio_request(GPIO_FN_SDHICMD1, NULL);
+ gpio_request(GPIO_FN_SDHICLK1, NULL);
+ gpio_request(GPIO_FN_SDHID1_3, NULL);
+ gpio_request(GPIO_FN_SDHID1_2, NULL);
+ gpio_request(GPIO_FN_SDHID1_1, NULL);
+ gpio_request(GPIO_FN_SDHID1_0, NULL);
/* MMCIF */
gpio_request(GPIO_FN_MMCD0_0, NULL);
/* set SPU2 clock to 119.6 MHz */
clk = clk_get(NULL, "spu_clk");
- if (!IS_ERR_VALUE(clk)) {
+ if (!IS_ERR(clk)) {
clk_set_rate(clk, clk_round_rate(clk, 119600000));
clk_put(clk);
}
/* change parent of FSI A */
clk = clk_get(NULL, "fsia_clk");
- if (!IS_ERR_VALUE(clk)) {
+ if (!IS_ERR(clk)) {
clk_register(&fsiackcr_clk);
clk_set_parent(clk, &fsiackcr_clk);
clk_put(clk);
i2c_register_board_info(1, i2c1_devices,
ARRAY_SIZE(i2c1_devices));
+#ifdef CONFIG_AP4EVB_QHD
+ /*
+ * QHD
+ */
+
+ /* enable KEYSC */
+ gpio_request(GPIO_FN_KEYOUT0, NULL);
+ gpio_request(GPIO_FN_KEYOUT1, NULL);
+ gpio_request(GPIO_FN_KEYOUT2, NULL);
+ gpio_request(GPIO_FN_KEYOUT3, NULL);
+ gpio_request(GPIO_FN_KEYOUT4, NULL);
+ gpio_request(GPIO_FN_KEYIN0_136, NULL);
+ gpio_request(GPIO_FN_KEYIN1_135, NULL);
+ gpio_request(GPIO_FN_KEYIN2_134, NULL);
+ gpio_request(GPIO_FN_KEYIN3_133, NULL);
+ gpio_request(GPIO_FN_KEYIN4, NULL);
+
+ /* enable TouchScreen */
+ set_irq_type(IRQ28, IRQ_TYPE_LEVEL_LOW);
+
+ tsc_device.irq = IRQ28;
+ i2c_register_board_info(1, &tsc_device, 1);
+
+ /* LCDC0 */
+ lcdc_info.clock_source = LCDC_CLK_PERIPHERAL;
+ lcdc_info.ch[0].interface_type = RGB24;
+ lcdc_info.ch[0].clock_divider = 1;
+ lcdc_info.ch[0].flags = LCDC_FLAGS_DWPOL;
+ lcdc_info.ch[0].lcd_cfg.name = "R63302(QHD)";
+ lcdc_info.ch[0].lcd_cfg.xres = 544;
+ lcdc_info.ch[0].lcd_cfg.yres = 961;
+ lcdc_info.ch[0].lcd_cfg.left_margin = 72;
+ lcdc_info.ch[0].lcd_cfg.right_margin = 600;
+ lcdc_info.ch[0].lcd_cfg.hsync_len = 16;
+ lcdc_info.ch[0].lcd_cfg.upper_margin = 8;
+ lcdc_info.ch[0].lcd_cfg.lower_margin = 8;
+ lcdc_info.ch[0].lcd_cfg.vsync_len = 2;
+ lcdc_info.ch[0].lcd_cfg.sync = FB_SYNC_VERT_HIGH_ACT |
+ FB_SYNC_HOR_HIGH_ACT;
+ lcdc_info.ch[0].lcd_size_cfg.width = 44;
+ lcdc_info.ch[0].lcd_size_cfg.height = 79;
+
+ platform_add_devices(qhd_devices, ARRAY_SIZE(qhd_devices));
+
+#else
+ /*
+ * WVGA
+ */
+ gpio_request(GPIO_FN_LCDD17, NULL);
+ gpio_request(GPIO_FN_LCDD16, NULL);
+ gpio_request(GPIO_FN_LCDD15, NULL);
+ gpio_request(GPIO_FN_LCDD14, NULL);
+ gpio_request(GPIO_FN_LCDD13, NULL);
+ gpio_request(GPIO_FN_LCDD12, NULL);
+ gpio_request(GPIO_FN_LCDD11, NULL);
+ gpio_request(GPIO_FN_LCDD10, NULL);
+ gpio_request(GPIO_FN_LCDD9, NULL);
+ gpio_request(GPIO_FN_LCDD8, NULL);
+ gpio_request(GPIO_FN_LCDD7, NULL);
+ gpio_request(GPIO_FN_LCDD6, NULL);
+ gpio_request(GPIO_FN_LCDD5, NULL);
+ gpio_request(GPIO_FN_LCDD4, NULL);
+ gpio_request(GPIO_FN_LCDD3, NULL);
+ gpio_request(GPIO_FN_LCDD2, NULL);
+ gpio_request(GPIO_FN_LCDD1, NULL);
+ gpio_request(GPIO_FN_LCDD0, NULL);
+ gpio_request(GPIO_FN_LCDDISP, NULL);
+ gpio_request(GPIO_FN_LCDDCK, NULL);
+
+ gpio_request(GPIO_PORT189, NULL); /* backlight */
+ gpio_direction_output(GPIO_PORT189, 1);
+
+ gpio_request(GPIO_PORT151, NULL); /* LCDDON */
+ gpio_direction_output(GPIO_PORT151, 1);
+
+ lcdc_info.clock_source = LCDC_CLK_BUS;
+ lcdc_info.ch[0].interface_type = RGB18;
+ lcdc_info.ch[0].clock_divider = 2;
+ lcdc_info.ch[0].flags = 0;
+ lcdc_info.ch[0].lcd_cfg.name = "WVGA Panel";
+ lcdc_info.ch[0].lcd_cfg.xres = 800;
+ lcdc_info.ch[0].lcd_cfg.yres = 480;
+ lcdc_info.ch[0].lcd_cfg.left_margin = 220;
+ lcdc_info.ch[0].lcd_cfg.right_margin = 110;
+ lcdc_info.ch[0].lcd_cfg.hsync_len = 70;
+ lcdc_info.ch[0].lcd_cfg.upper_margin = 20;
+ lcdc_info.ch[0].lcd_cfg.lower_margin = 5;
+ lcdc_info.ch[0].lcd_cfg.vsync_len = 5;
+ lcdc_info.ch[0].lcd_cfg.sync = 0;
+ lcdc_info.ch[0].lcd_size_cfg.width = 152;
+ lcdc_info.ch[0].lcd_size_cfg.height = 91;
+
+ /* enable TouchScreen */
+ set_irq_type(IRQ7, IRQ_TYPE_LEVEL_LOW);
+
+ tsc_device.irq = IRQ7;
+ i2c_register_board_info(0, &tsc_device, 1);
+#endif /* CONFIG_AP4EVB_QHD */
+
sh7372_add_standard_devices();
+ /* HDMI */
+ gpio_request(GPIO_FN_HDMI_HPD, NULL);
+ gpio_request(GPIO_FN_HDMI_CEC, NULL);
+
+ /* Reset HDMI, must be held at least one EXTALR (32768Hz) period */
+#define SRCR4 0xe61580bc
+ srcr4 = __raw_readl(SRCR4);
+ __raw_writel(srcr4 | (1 << 13), SRCR4);
+ udelay(50);
+ __raw_writel(srcr4 & ~(1 << 13), SRCR4);
+
platform_add_devices(ap4evb_devices, ARRAY_SIZE(ap4evb_devices));
}
{
sh7372_clock_init();
shmobile_timer.init();
+
+ /* External clock source */
+ clk_set_rate(&dv_clki_clk, 27000000);
}
static struct sys_timer ap4evb_timer = {