#include <linux/major.h>
#include <linux/fb.h>
#include <linux/interrupt.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
+#include <asm/arch/pxa2xx_spi.h>
#include <asm/setup.h>
#include <asm/memory.h>
#include <asm/mach-types.h>
#include <asm/hardware.h>
#include <asm/irq.h>
+#include <asm/sizes.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
+#include <asm/mach/flash.h>
#include <asm/hardware/sa1111.h>
},
};
+/* ADS7846 is connected through SSP ... and if your board has J5 populated,
+ * you can select it to replace the ucb1400 by switching the touchscreen cable
+ * (to J5) and poking board registers (as done below). Else it's only useful
+ * for the temperature sensors.
+ */
+static struct resource pxa_ssp_resources[] = {
+ [0] = {
+ .start = __PREG(SSCR0_P(1)),
+ .end = __PREG(SSCR0_P(1)) + 0x14,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_SSP,
+ .end = IRQ_SSP,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct pxa2xx_spi_master pxa_ssp_master_info = {
+ .ssp_type = PXA25x_SSP,
+ .clock_enable = CKEN3_SSP,
+ .num_chipselect = 0,
+};
+
+static struct platform_device pxa_ssp = {
+ .name = "pxa2xx-spi",
+ .id = 1,
+ .resource = pxa_ssp_resources,
+ .num_resources = ARRAY_SIZE(pxa_ssp_resources),
+ .dev = {
+ .platform_data = &pxa_ssp_master_info,
+ },
+};
+
+static int lubbock_ads7846_pendown_state(void)
+{
+ /* TS_BUSY is bit 8 in LUB_MISC_RD, but pendown is irq-only */
+ return 0;
+}
+
+static struct ads7846_platform_data ads_info = {
+ .model = 7846,
+ .vref_delay_usecs = 100, /* internal, no cap */
+ .get_pendown_state = lubbock_ads7846_pendown_state,
+ // .x_plate_ohms = 500, /* GUESS! */
+ // .y_plate_ohms = 500, /* GUESS! */
+};
+
+static void ads7846_cs(u32 command)
+{
+ static const unsigned TS_nCS = 1 << 11;
+ lubbock_set_misc_wr(TS_nCS, (command == PXA2XX_CS_ASSERT) ? 0 : TS_nCS);
+}
+
+static struct pxa2xx_spi_chip ads_hw = {
+ .tx_threshold = 1,
+ .rx_threshold = 2,
+ .cs_control = ads7846_cs,
+};
+
+static struct spi_board_info spi_board_info[] __initdata = { {
+ .modalias = "ads7846",
+ .platform_data = &ads_info,
+ .controller_data = &ads_hw,
+ .irq = LUBBOCK_BB_IRQ,
+ .max_speed_hz = 120000 /* max sample rate at 3V */
+ * 26 /* command + data + overhead */,
+ .bus_num = 1,
+ .chip_select = 0,
+},
+};
+
static struct platform_device smc91x_device = {
.name = "smc91x",
.id = -1,
.resource = smc91x_resources,
};
+static struct resource flash_resources[] = {
+ [0] = {
+ .start = 0x00000000,
+ .end = SZ_64M - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = 0x04000000,
+ .end = 0x04000000 + SZ_64M - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct mtd_partition lubbock_partitions[] = {
+ {
+ .name = "Bootloader",
+ .size = 0x00040000,
+ .offset = 0,
+ .mask_flags = MTD_WRITEABLE /* force read-only */
+ },{
+ .name = "Kernel",
+ .size = 0x00100000,
+ .offset = 0x00040000,
+ },{
+ .name = "Filesystem",
+ .size = MTDPART_SIZ_FULL,
+ .offset = 0x00140000
+ }
+};
+
+static struct flash_platform_data lubbock_flash_data[2] = {
+ {
+ .map_name = "cfi_probe",
+ .parts = lubbock_partitions,
+ .nr_parts = ARRAY_SIZE(lubbock_partitions),
+ }, {
+ .map_name = "cfi_probe",
+ .parts = NULL,
+ .nr_parts = 0,
+ }
+};
+
+static struct platform_device lubbock_flash_device[2] = {
+ {
+ .name = "pxa2xx-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &lubbock_flash_data[0],
+ },
+ .resource = &flash_resources[0],
+ .num_resources = 1,
+ },
+ {
+ .name = "pxa2xx-flash",
+ .id = 1,
+ .dev = {
+ .platform_data = &lubbock_flash_data[1],
+ },
+ .resource = &flash_resources[1],
+ .num_resources = 1,
+ },
+};
+
static struct platform_device *devices[] __initdata = {
&sa1111_device,
&lub_audio_device,
&smc91x_device,
+ &lubbock_flash_device[0],
+ &lubbock_flash_device[1],
+ &pxa_ssp,
};
static struct pxafb_mach_info sharp_lm8v31 __initdata = {
init_timer(&mmc_timer);
mmc_timer.data = (unsigned long) data;
return request_irq(LUBBOCK_SD_IRQ, lubbock_detect_int,
- SA_SAMPLE_RANDOM, "lubbock-sd-detect", data);
+ IRQF_SAMPLE_RANDOM, "lubbock-sd-detect", data);
}
static int lubbock_mci_get_ro(struct device *dev)
static void __init lubbock_init(void)
{
+ int flashboot = (LUB_CONF_SWITCHES & 1);
+
pxa_set_udc_info(&udc_info);
set_pxa_fb_info(&sharp_lm8v31);
pxa_set_mci_info(&lubbock_mci_platform_data);
pxa_set_ficp_info(&lubbock_ficp_platform_data);
+
+ lubbock_flash_data[0].width = lubbock_flash_data[1].width =
+ (BOOT_DEF & 1) ? 2 : 4;
+ /* Compensate for the nROMBT switch which swaps the flash banks */
+ printk(KERN_NOTICE "Lubbock configured to boot from %s (bank %d)\n",
+ flashboot?"Flash":"ROM", flashboot);
+
+ lubbock_flash_data[flashboot^1].name = "application-flash";
+ lubbock_flash_data[flashboot].name = "boot-rom";
(void) platform_add_devices(devices, ARRAY_SIZE(devices));
+
+ spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
}
static struct map_desc lubbock_io_desc[] __initdata = {
pxa_map_io();
iotable_init(lubbock_io_desc, ARRAY_SIZE(lubbock_io_desc));
+ /* SSP data pins */
+ pxa_gpio_mode(GPIO23_SCLK_MD);
+ pxa_gpio_mode(GPIO25_STXD_MD);
+ pxa_gpio_mode(GPIO26_SRXD_MD);
+
/* This enables the BTUART */
pxa_gpio_mode(GPIO42_BTRXD_MD);
pxa_gpio_mode(GPIO43_BTTXD_MD);
MACHINE_START(LUBBOCK, "Intel DBPXA250 Development Platform (aka Lubbock)")
/* Maintainer: MontaVista Software Inc. */
- .phys_ram = 0xa0000000,
.phys_io = 0x40000000,
.io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
.map_io = lubbock_map_io,