#ifndef __ASM_ARCH_MFP_PXA3XX_H
#define __ASM_ARCH_MFP_PXA3XX_H
-#define MFPR_BASE (0x40e10000)
-#define MFPR_SIZE (PAGE_SIZE)
-
-/* MFPR register bit definitions */
-#define MFPR_PULL_SEL (0x1 << 15)
-#define MFPR_PULLUP_EN (0x1 << 14)
-#define MFPR_PULLDOWN_EN (0x1 << 13)
-#define MFPR_SLEEP_SEL (0x1 << 9)
-#define MFPR_SLEEP_OE_N (0x1 << 7)
-#define MFPR_EDGE_CLEAR (0x1 << 6)
-#define MFPR_EDGE_FALL_EN (0x1 << 5)
-#define MFPR_EDGE_RISE_EN (0x1 << 4)
-
-#define MFPR_SLEEP_DATA(x) ((x) << 8)
-#define MFPR_DRIVE(x) (((x) & 0x7) << 10)
-#define MFPR_AF_SEL(x) (((x) & 0x7) << 0)
+#include <plat/mfp.h>
-#define MFPR_EDGE_NONE (0)
-#define MFPR_EDGE_RISE (MFPR_EDGE_RISE_EN)
-#define MFPR_EDGE_FALL (MFPR_EDGE_FALL_EN)
-#define MFPR_EDGE_BOTH (MFPR_EDGE_RISE | MFPR_EDGE_FALL)
-
-/*
- * Table that determines the low power modes outputs, with actual settings
- * used in parentheses for don't-care values. Except for the float output,
- * the configured driven and pulled levels match, so if there is a need for
- * non-LPM pulled output, the same configuration could probably be used.
- *
- * Output value sleep_oe_n sleep_data pullup_en pulldown_en pull_sel
- * (bit 7) (bit 8) (bit 14) (bit 13) (bit 15)
- *
- * Input 0 X(0) X(0) X(0) 0
- * Drive 0 0 0 0 X(1) 0
- * Drive 1 0 1 X(1) 0 0
- * Pull hi (1) 1 X(1) 1 0 0
- * Pull lo (0) 1 X(0) 0 1 0
- * Z (float) 1 X(0) 0 0 0
- */
-#define MFPR_LPM_INPUT (0)
-#define MFPR_LPM_DRIVE_LOW (MFPR_SLEEP_DATA(0) | MFPR_PULLDOWN_EN)
-#define MFPR_LPM_DRIVE_HIGH (MFPR_SLEEP_DATA(1) | MFPR_PULLUP_EN)
-#define MFPR_LPM_PULL_LOW (MFPR_LPM_DRIVE_LOW | MFPR_SLEEP_OE_N)
-#define MFPR_LPM_PULL_HIGH (MFPR_LPM_DRIVE_HIGH | MFPR_SLEEP_OE_N)
-#define MFPR_LPM_FLOAT (MFPR_SLEEP_OE_N)
-#define MFPR_LPM_MASK (0xe080)
-
-/*
- * The pullup and pulldown state of the MFP pin at run mode is by default
- * determined by the selected alternate function. In case that some buggy
- * devices need to override this default behavior, the definitions below
- * indicates the setting of corresponding MFPR bits
- *
- * Definition pull_sel pullup_en pulldown_en
- * MFPR_PULL_NONE 0 0 0
- * MFPR_PULL_LOW 1 0 1
- * MFPR_PULL_HIGH 1 1 0
- * MFPR_PULL_BOTH 1 1 1
- */
-#define MFPR_PULL_NONE (0)
-#define MFPR_PULL_LOW (MFPR_PULL_SEL | MFPR_PULLDOWN_EN)
-#define MFPR_PULL_BOTH (MFPR_PULL_LOW | MFPR_PULLUP_EN)
-#define MFPR_PULL_HIGH (MFPR_PULL_SEL | MFPR_PULLUP_EN)
+#define MFPR_BASE (0x40e10000)
/* PXA3xx common MFP configurations - processor specific ones defined
* in mfp-pxa300.h and mfp-pxa320.h
#define GPIO5_2_GPIO MFP_CFG(GPIO5_2, AF0)
#define GPIO6_2_GPIO MFP_CFG(GPIO6_2, AF0)
-/*
- * each MFP pin will have a MFPR register, since the offset of the
- * register varies between processors, the processor specific code
- * should initialize the pin offsets by pxa3xx_mfp_init_addr()
- *
- * pxa3xx_mfp_init_addr - accepts a table of "pxa3xx_mfp_addr_map"
- * structure, which represents a range of MFP pins from "start" to
- * "end", with the offset begining at "offset", to define a single
- * pin, let "end" = -1
- *
- * use
- *
- * MFP_ADDR_X() to define a range of pins
- * MFP_ADDR() to define a single pin
- * MFP_ADDR_END to signal the end of pin offset definitions
- */
-struct pxa3xx_mfp_addr_map {
- unsigned int start;
- unsigned int end;
- unsigned long offset;
-};
-
-#define MFP_ADDR_X(start, end, offset) \
- { MFP_PIN_##start, MFP_PIN_##end, offset }
-
-#define MFP_ADDR(pin, offset) \
- { MFP_PIN_##pin, -1, offset }
-
-#define MFP_ADDR_END { MFP_PIN_INVALID, 0 }
-
-/*
- * pxa3xx_mfp_read()/pxa3xx_mfp_write() - for direct read/write access
- * to the MFPR register
- */
-unsigned long pxa3xx_mfp_read(int mfp);
-void pxa3xx_mfp_write(int mfp, unsigned long mfpr_val);
-
-/*
- * pxa3xx_mfp_config - configure the MFPR registers
- *
- * used by board specific initialization code
- */
-void pxa3xx_mfp_config(unsigned long *mfp_cfgs, int num);
-
-/*
- * pxa3xx_mfp_init_addr() - initialize the mapping between mfp pin
- * index and MFPR register offset
- *
- * used by processor specific code
+/* NOTE: usage of these two functions is not recommended,
+ * use pxa3xx_mfp_config() instead.
*/
-void __init pxa3xx_mfp_init_addr(struct pxa3xx_mfp_addr_map *);
-void __init pxa3xx_init_mfp(void);
+static inline unsigned long pxa3xx_mfp_read(int mfp)
+{
+ return mfp_read(mfp);
+}
+
+static inline void pxa3xx_mfp_write(int mfp, unsigned long val)
+{
+ mfp_write(mfp, val);
+}
+
+static inline void pxa3xx_mfp_config(unsigned long *mfp_cfg, int num)
+{
+ mfp_config(mfp_cfg, num);
+}
#endif /* __ASM_ARCH_MFP_PXA3XX_H */
git.openpandora.org / pandora-kernel.git / blobdiff