*/
#ifdef MULTI_OMAP2
+
+/*
+ * We use __glue to avoid errors with multiple definitions of
+ * .globl omap_irq_base as it's included from entry-armv.S but not
+ * from entry-common.S.
+ */
+#ifdef __glue
.pushsection .data
-omap_irq_base: .word 0
+ .globl omap_irq_base
+omap_irq_base:
+ .word 0
.popsection
+#endif
- /* Configure the interrupt base on the first interrupt */
+ /*
+ * Configure the interrupt base on the first interrupt.
+ * See also omap_irq_base_init for setting omap_irq_base.
+ */
.macro get_irqnr_preamble, base, tmp
-9:
ldr \base, =omap_irq_base @ irq base address
ldr \base, [\base, #0] @ irq base value
- cmp \base, #0 @ already configured?
- bne 9997f @ nothing to do
-
- mrc p15, 0, \tmp, c0, c0, 0 @ get processor revision
- and \tmp, \tmp, #0x000f0000 @ only check architecture
- cmp \tmp, #0x00070000 @ is v6?
- beq 2400f @ found v6 so it's omap24xx
- mrc p15, 0, \tmp, c0, c0, 0 @ get processor revision
- and \tmp, \tmp, #0x000000f0 @ check cortex 8 or 9
- cmp \tmp, #0x00000080 @ cortex A-8?
- beq 3400f @ found A-8 so it's omap34xx
- cmp \tmp, #0x00000090 @ cortex A-9?
- beq 4400f @ found A-9 so it's omap44xx
-2400: ldr \base, =OMAP2_IRQ_BASE
- ldr \tmp, =omap_irq_base
- str \base, [\tmp, #0]
- b 9b
-3400: ldr \base, =OMAP3_IRQ_BASE
- ldr \tmp, =omap_irq_base
- str \base, [\tmp, #0]
- b 9b
-4400: ldr \base, =OMAP4_IRQ_BASE
- ldr \tmp, =omap_irq_base
- str \base, [\tmp, #0]
- b 9b
-9997:
.endm
/* Check the pending interrupts. Note that base already set */
9999:
.endm
+#ifdef CONFIG_SMP
+ /* We assume that irqstat (the raw value of the IRQ acknowledge
+ * register) is preserved from the macro above.
+ * If there is an IPI, we immediately signal end of interrupt
+ * on the controller, since this requires the original irqstat
+ * value which we won't easily be able to recreate later.
+ */
+
+ .macro test_for_ipi, irqnr, irqstat, base, tmp
+ bic \irqnr, \irqstat, #0x1c00
+ cmp \irqnr, #16
+ it cc
+ strcc \irqstat, [\base, #GIC_CPU_EOI]
+ it cs
+ cmpcs \irqnr, \irqnr
+ .endm
+
+ /* As above, this assumes that irqstat and base are preserved */
+
+ .macro test_for_ltirq, irqnr, irqstat, base, tmp
+ bic \irqnr, \irqstat, #0x1c00
+ mov \tmp, #0
+ cmp \irqnr, #29
+ itt eq
+ moveq \tmp, #1
+ streq \irqstat, [\base, #GIC_CPU_EOI]
+ cmp \tmp, #0
+ .endm
+#endif /* CONFIG_SMP */
#else /* MULTI_OMAP2 */
#ifdef CONFIG_ARCH_OMAP4
+#define HAVE_GET_IRQNR_PREAMBLE
+#include <asm/hardware/entry-macro-gic.S>
.macro get_irqnr_preamble, base, tmp
ldr \base, =OMAP4_IRQ_BASE
.endm
- /*
- * The interrupt numbering scheme is defined in the
- * interrupt controller spec. To wit:
- *
- * Interrupts 0-15 are IPI
- * 16-28 are reserved
- * 29-31 are local. We allow 30 to be used for the watchdog.
- * 32-1020 are global
- * 1021-1022 are reserved
- * 1023 is "spurious" (no interrupt)
- *
- * For now, we ignore all local interrupts so only return an
- * interrupt if it's between 30 and 1020. The test_for_ipi
- * routine below will pick up on IPIs.
- * A simple read from the controller will tell us the number
- * of the highest priority enabled interrupt.
- * We then just need to check whether it is in the
- * valid range for an IRQ (30-1020 inclusive).
- */
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
- ldr \irqstat, [\base, #GIC_CPU_INTACK]
-
- ldr \tmp, =1021
-
- bic \irqnr, \irqstat, #0x1c00
-
- cmp \irqnr, #29
- cmpcc \irqnr, \irqnr
- cmpne \irqnr, \tmp
- cmpcs \irqnr, \irqnr
- .endm
#endif
-#endif /* MULTI_OMAP2 */
-
-#ifdef CONFIG_SMP
- /* We assume that irqstat (the raw value of the IRQ acknowledge
- * register) is preserved from the macro above.
- * If there is an IPI, we immediately signal end of interrupt
- * on the controller, since this requires the original irqstat
- * value which we won't easily be able to recreate later.
- */
- .macro test_for_ipi, irqnr, irqstat, base, tmp
- bic \irqnr, \irqstat, #0x1c00
- cmp \irqnr, #16
- it cc
- strcc \irqstat, [\base, #GIC_CPU_EOI]
- it cs
- cmpcs \irqnr, \irqnr
- .endm
-
- /* As above, this assumes that irqstat and base are preserved */
-
- .macro test_for_ltirq, irqnr, irqstat, base, tmp
- bic \irqnr, \irqstat, #0x1c00
- mov \tmp, #0
- cmp \irqnr, #29
- itt eq
- moveq \tmp, #1
- streq \irqstat, [\base, #GIC_CPU_EOI]
- cmp \tmp, #0
- .endm
-#endif /* CONFIG_SMP */
+#endif /* MULTI_OMAP2 */
.macro irq_prio_table
.endm
git.openpandora.org / pandora-kernel.git / blobdiff