dd = clk->dpll_data;
/* DPLL divider must result in a valid jitter correction val */
- fint = clk->parent->rate / (n + 1);
+ fint = clk->parent->rate / n;
if (fint < DPLL_FINT_BAND1_MIN) {
pr_debug("rejecting n=%d due to Fint failure, "
if (!dd)
return;
- /* Return bypass rate if DPLL is bypassed */
v = __raw_readl(dd->control_reg);
v &= dd->enable_mask;
v >>= __ffs(dd->enable_mask);
- /* Reparent in case the dpll is in bypass */
+ /* Reparent the struct clk in case the dpll is in bypass */
if (cpu_is_omap24xx()) {
if (v == OMAP2XXX_EN_DPLL_LPBYPASS ||
v == OMAP2XXX_EN_DPLL_FRBYPASS)
/* DPLL rate rounding code */
-/**
- * omap2_dpll_set_rate_tolerance: set the error tolerance during rate rounding
- * @clk: struct clk * of the DPLL
- * @tolerance: maximum rate error tolerance
- *
- * Set the maximum DPLL rate error tolerance for the rate rounding
- * algorithm. The rate tolerance is an attempt to balance DPLL power
- * saving (the least divider value "n") vs. rate fidelity (the least
- * difference between the desired DPLL target rate and the rounded
- * rate out of the algorithm). So, increasing the tolerance is likely
- * to decrease DPLL power consumption and increase DPLL rate error.
- * Returns -EINVAL if provided a null clock ptr or a clk that is not a
- * DPLL; or 0 upon success.
- */
-int omap2_dpll_set_rate_tolerance(struct clk *clk, unsigned int tolerance)
-{
- if (!clk || !clk->dpll_data)
- return -EINVAL;
-
- clk->dpll_data->rate_tolerance = tolerance;
-
- return 0;
-}
-
/**
* omap2_dpll_round_rate - round a target rate for an OMAP DPLL
* @clk: struct clk * for a DPLL
* @target_rate: desired DPLL clock rate
*
- * Given a DPLL, a desired target rate, and a rate tolerance, round
- * the target rate to a possible, programmable rate for this DPLL.
- * Rate tolerance is assumed to be set by the caller before this
- * function is called. Attempts to select the minimum possible n
- * within the tolerance to reduce power consumption. Stores the
- * computed (m, n) in the DPLL's dpll_data structure so set_rate()
- * will not need to call this (expensive) function again. Returns ~0
- * if the target rate cannot be rounded, either because the rate is
- * too low or because the rate tolerance is set too tightly; or the
- * rounded rate upon success.
+ * Given a DPLL and a desired target rate, round the target rate to a
+ * possible, programmable rate for this DPLL. Attempts to select the
+ * minimum possible n. Stores the computed (m, n) in the DPLL's
+ * dpll_data structure so set_rate() will not need to call this
+ * (expensive) function again. Returns ~0 if the target rate cannot
+ * be rounded, or the rounded rate upon success.
*/
long omap2_dpll_round_rate(struct clk *clk, unsigned long target_rate)
{
- int m, n, r, e, scaled_max_m;
- unsigned long scaled_rt_rp, new_rate;
- int min_e = -1, min_e_m = -1, min_e_n = -1;
+ int m, n, r, scaled_max_m;
+ unsigned long scaled_rt_rp;
+ unsigned long new_rate = 0;
struct dpll_data *dd;
if (!clk || !clk->dpll_data)
dd = clk->dpll_data;
- pr_debug("clock: starting DPLL round_rate for clock %s, target rate "
- "%ld\n", clk->name, target_rate);
+ pr_debug("clock: %s: starting DPLL round_rate, target rate %ld\n",
+ clk->name, target_rate);
scaled_rt_rp = target_rate / (dd->clk_ref->rate / DPLL_SCALE_FACTOR);
scaled_max_m = dd->max_multiplier * DPLL_SCALE_FACTOR;
if (r == DPLL_MULT_UNDERFLOW)
continue;
- e = target_rate - new_rate;
- pr_debug("clock: n = %d: m = %d: rate error is %d "
- "(new_rate = %ld)\n", n, m, e, new_rate);
-
- if (min_e == -1 ||
- min_e >= (int)(abs(e) - dd->rate_tolerance)) {
- min_e = e;
- min_e_m = m;
- min_e_n = n;
-
- pr_debug("clock: found new least error %d\n", min_e);
+ pr_debug("clock: %s: m = %d: n = %d: new_rate = %ld\n",
+ clk->name, m, n, new_rate);
- /* We found good settings -- bail out now */
- if (min_e <= dd->rate_tolerance)
- break;
+ if (target_rate == new_rate) {
+ dd->last_rounded_m = m;
+ dd->last_rounded_n = n;
+ dd->last_rounded_rate = target_rate;
+ break;
}
}
- if (min_e < 0) {
- pr_debug("clock: error: target rate or tolerance too low\n");
+ if (target_rate != new_rate) {
+ pr_debug("clock: %s: cannot round to rate %ld\n", clk->name,
+ target_rate);
return ~0;
}
- dd->last_rounded_m = min_e_m;
- dd->last_rounded_n = min_e_n;
- dd->last_rounded_rate = _dpll_compute_new_rate(dd->clk_ref->rate,
- min_e_m, min_e_n);
-
- pr_debug("clock: final least error: e = %d, m = %d, n = %d\n",
- min_e, min_e_m, min_e_n);
- pr_debug("clock: final rate: %ld (target rate: %ld)\n",
- dd->last_rounded_rate, target_rate);
-
- return dd->last_rounded_rate;
+ return target_rate;
}
git.openpandora.org / pandora-kernel.git / blobdiff