#include <plat/mcspi.h>
#include <linux/input/matrix_keypad.h>
#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
#include <linux/interrupt.h>
#include <linux/smsc911x.h>
#include <linux/i2c/at24.h>
#include "sdram-micron-mt46h32m32lf-6.h"
#include "mux.h"
#include "hsmmc.h"
-#include "timer-gp.h"
+#include "common-board-devices.h"
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#include <plat/gpmc-smsc911x.h>
+
#define OMAP3STALKER_ETHR_START 0x2c000000
#define OMAP3STALKER_ETHR_SIZE 1024
#define OMAP3STALKER_ETHR_GPIO_IRQ 19
#define OMAP3STALKER_SMC911X_CS 5
-static struct resource omap3stalker_smsc911x_resources[] = {
- [0] = {
- .start = OMAP3STALKER_ETHR_START,
- .end =
- (OMAP3STALKER_ETHR_START + OMAP3STALKER_ETHR_SIZE - 1),
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = OMAP_GPIO_IRQ(OMAP3STALKER_ETHR_GPIO_IRQ),
- .end = OMAP_GPIO_IRQ(OMAP3STALKER_ETHR_GPIO_IRQ),
- .flags = (IORESOURCE_IRQ | IRQF_TRIGGER_LOW),
- },
-};
-
-static struct smsc911x_platform_config smsc911x_config = {
- .phy_interface = PHY_INTERFACE_MODE_MII,
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+static struct omap_smsc911x_platform_data smsc911x_cfg = {
+ .cs = OMAP3STALKER_SMC911X_CS,
+ .gpio_irq = OMAP3STALKER_ETHR_GPIO_IRQ,
+ .gpio_reset = -EINVAL,
.flags = (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS),
};
-static struct platform_device omap3stalker_smsc911x_device = {
- .name = "smsc911x",
- .id = -1,
- .num_resources = ARRAY_SIZE(omap3stalker_smsc911x_resources),
- .resource = &omap3stalker_smsc911x_resources[0],
- .dev = {
- .platform_data = &smsc911x_config,
- },
-};
-
static inline void __init omap3stalker_init_eth(void)
{
- int eth_cs;
struct clk *l3ck;
unsigned int rate;
- eth_cs = OMAP3STALKER_SMC911X_CS;
-
l3ck = clk_get(NULL, "l3_ck");
if (IS_ERR(l3ck))
rate = 100000000;
rate = clk_get_rate(l3ck);
omap_mux_init_gpio(19, OMAP_PIN_INPUT_PULLUP);
- if (gpio_request(OMAP3STALKER_ETHR_GPIO_IRQ, "SMC911x irq") < 0) {
- printk(KERN_ERR
- "Failed to request GPIO%d for smc911x IRQ\n",
- OMAP3STALKER_ETHR_GPIO_IRQ);
- return;
- }
-
- gpio_direction_input(OMAP3STALKER_ETHR_GPIO_IRQ);
-
- platform_device_register(&omap3stalker_smsc911x_device);
+ gpmc_smsc911x_init(&smsc911x_cfg);
}
#else
.default_device = &omap3_stalker_dvi_device,
};
-static struct regulator_consumer_supply omap3stalker_vmmc1_supply = {
- .supply = "vmmc",
+static struct regulator_consumer_supply omap3stalker_vmmc1_supply[] = {
+ REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
};
-static struct regulator_consumer_supply omap3stalker_vsim_supply = {
- .supply = "vmmc_aux",
+static struct regulator_consumer_supply omap3stalker_vsim_supply[] = {
+ REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
};
/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
| REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
},
- .num_consumer_supplies = 1,
- .consumer_supplies = &omap3stalker_vmmc1_supply,
+ .num_consumer_supplies = ARRAY_SIZE(omap3stalker_vmmc1_supply),
+ .consumer_supplies = omap3stalker_vmmc1_supply,
};
/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
| REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
},
- .num_consumer_supplies = 1,
- .consumer_supplies = &omap3stalker_vsim_supply,
+ .num_consumer_supplies = ARRAY_SIZE(omap3stalker_vsim_supply),
+ .consumer_supplies = omap3stalker_vsim_supply,
};
static struct omap2_hsmmc_info mmc[] = {
mmc[0].gpio_cd = gpio + 0;
omap2_hsmmc_init(mmc);
- /* link regulators to MMC adapters */
- omap3stalker_vmmc1_supply.dev = mmc[0].dev;
- omap3stalker_vsim_supply.dev = mmc[0].dev;
-
/*
* Most GPIOs are for USB OTG. Some are mostly sent to
* the P2 connector; notably LEDA for the LCD backlight.
*/
/* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */
- gpio_request(gpio + TWL4030_GPIO_MAX, "EN_LCD_BKL");
- gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0);
+ gpio_request_one(gpio + TWL4030_GPIO_MAX, GPIOF_OUT_INIT_LOW,
+ "EN_LCD_BKL");
/* gpio + 7 == DVI Enable */
- gpio_request(gpio + 7, "EN_DVI");
- gpio_direction_output(gpio + 7, 0);
+ gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
/* TWL4030_GPIO_MAX + 1 == ledB (out, mmc0) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
.setup = omap3stalker_twl_gpio_setup,
};
-static struct twl4030_usb_data omap3stalker_usb_data = {
- .usb_mode = T2_USB_MODE_ULPI,
-};
-
static uint32_t board_keymap[] = {
KEY(0, 0, KEY_LEFT),
KEY(0, 1, KEY_DOWN),
.rep = 1,
};
-static struct twl4030_madc_platform_data omap3stalker_madc_data = {
- .irq_line = 1,
-};
-
-static struct twl4030_codec_audio_data omap3stalker_audio_data;
-
-static struct twl4030_codec_data omap3stalker_codec_data = {
- .audio_mclk = 26000000,
- .audio = &omap3stalker_audio_data,
-};
-
-static struct regulator_consumer_supply omap3_stalker_vdda_dac_supply =
- REGULATOR_SUPPLY("vdda_dac", "omapdss_venc");
-
-/* VDAC for DSS driving S-Video */
-static struct regulator_init_data omap3_stalker_vdac = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = 1,
- .consumer_supplies = &omap3_stalker_vdda_dac_supply,
-};
-
-/* VPLL2 for digital video outputs */
-static struct regulator_consumer_supply omap3_stalker_vpll2_supplies[] = {
- REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi1"),
-};
-
-static struct regulator_init_data omap3_stalker_vpll2 = {
- .constraints = {
- .name = "VDVI",
- .min_uV = 1800000,
- .max_uV = 1800000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap3_stalker_vpll2_supplies),
- .consumer_supplies = omap3_stalker_vpll2_supplies,
-};
-
static struct twl4030_platform_data omap3stalker_twldata = {
- .irq_base = TWL4030_IRQ_BASE,
- .irq_end = TWL4030_IRQ_END,
-
/* platform_data for children goes here */
.keypad = &omap3stalker_kp_data,
- .madc = &omap3stalker_madc_data,
- .usb = &omap3stalker_usb_data,
.gpio = &omap3stalker_gpio_data,
- .codec = &omap3stalker_codec_data,
- .vdac = &omap3_stalker_vdac,
- .vpll2 = &omap3_stalker_vpll2,
-};
-
-static struct i2c_board_info __initdata omap3stalker_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("twl4030", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &omap3stalker_twldata,
- },
+ .vmmc1 = &omap3stalker_vmmc1,
+ .vsim = &omap3stalker_vsim,
};
static struct at24_platform_data fram_info = {
static int __init omap3_stalker_i2c_init(void)
{
- /*
- * REVISIT: These entries can be set in omap3evm_twl_data
- * after a merge with MFD tree
- */
- omap3stalker_twldata.vmmc1 = &omap3stalker_vmmc1;
- omap3stalker_twldata.vsim = &omap3stalker_vsim;
+ omap3_pmic_get_config(&omap3stalker_twldata,
+ TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
+ TWL_COMMON_PDATA_AUDIO,
+ TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
+
+ omap3stalker_twldata.vdac->constraints.apply_uV = true;
+ omap3stalker_twldata.vpll2->constraints.apply_uV = true;
+ omap3stalker_twldata.vpll2->constraints.name = "VDVI";
- omap_register_i2c_bus(1, 2600, omap3stalker_i2c_boardinfo,
- ARRAY_SIZE(omap3stalker_i2c_boardinfo));
+ omap3_pmic_init("twl4030", &omap3stalker_twldata);
omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(3, 400, omap3stalker_i2c_boardinfo3,
ARRAY_SIZE(omap3stalker_i2c_boardinfo3));
}
#define OMAP3_STALKER_TS_GPIO 175
-static void ads7846_dev_init(void)
-{
- if (gpio_request(OMAP3_STALKER_TS_GPIO, "ADS7846 pendown") < 0)
- printk(KERN_ERR "can't get ads7846 pen down GPIO\n");
-
- gpio_direction_input(OMAP3_STALKER_TS_GPIO);
- gpio_set_debounce(OMAP3_STALKER_TS_GPIO, 310);
-}
-
-static int ads7846_get_pendown_state(void)
-{
- return !gpio_get_value(OMAP3_STALKER_TS_GPIO);
-}
-
-static struct ads7846_platform_data ads7846_config = {
- .x_max = 0x0fff,
- .y_max = 0x0fff,
- .x_plate_ohms = 180,
- .pressure_max = 255,
- .debounce_max = 10,
- .debounce_tol = 3,
- .debounce_rep = 1,
- .get_pendown_state = ads7846_get_pendown_state,
- .keep_vref_on = 1,
- .settle_delay_usecs = 150,
-};
-
-static struct omap2_mcspi_device_config ads7846_mcspi_config = {
- .turbo_mode = 0,
- .single_channel = 1, /* 0: slave, 1: master */
-};
-
-static struct spi_board_info omap3stalker_spi_board_info[] = {
- [0] = {
- .modalias = "ads7846",
- .bus_num = 1,
- .chip_select = 0,
- .max_speed_hz = 1500000,
- .controller_data = &ads7846_mcspi_config,
- .irq = OMAP_GPIO_IRQ(OMAP3_STALKER_TS_GPIO),
- .platform_data = &ads7846_config,
- },
-};
static struct omap_board_config_kernel omap3_stalker_config[] __initdata = {
};
static void __init omap3_stalker_init_irq(void)
{
- omap_init_irq();
-#ifdef CONFIG_OMAP_32K_TIMER
- omap2_gp_clockevent_set_gptimer(12);
-#endif
+ omap3_init_irq();
}
static struct platform_device *omap3_stalker_devices[] __initdata = {
};
#endif
-static struct omap_musb_board_data musb_board_data = {
- .interface_type = MUSB_INTERFACE_ULPI,
- .mode = MUSB_OTG,
- .power = 100,
-};
-
static void __init omap3_stalker_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
ARRAY_SIZE(omap3_stalker_devices));
omap_display_init(&omap3_stalker_dss_data);
- spi_register_board_info(omap3stalker_spi_board_info,
- ARRAY_SIZE(omap3stalker_spi_board_info));
omap_serial_init();
- usb_musb_init(&musb_board_data);
+ usb_musb_init(NULL);
usbhs_init(&usbhs_bdata);
- ads7846_dev_init();
+ omap_ads7846_init(1, OMAP3_STALKER_TS_GPIO, 310, NULL);
omap_mux_init_gpio(21, OMAP_PIN_OUTPUT);
omap_mux_init_gpio(18, OMAP_PIN_INPUT_PULLUP);
.init_early = omap3_stalker_init_early,
.init_irq = omap3_stalker_init_irq,
.init_machine = omap3_stalker_init,
- .timer = &omap_timer,
+ .timer = &omap3_secure_timer,
MACHINE_END
git.openpandora.org / pandora-kernel.git / blobdiff