#include "mux.h"
#include "sdram-micron-mt46h32m32lf-6.h"
#include "hsmmc.h"
+#include "common-board-devices.h"
#define OMAP3_EVM_TS_GPIO 175
#define OMAP3_EVM_EHCI_VBUS 22
}
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
-static struct resource omap3evm_smsc911x_resources[] = {
- [0] = {
- .start = OMAP3EVM_ETHR_START,
- .end = (OMAP3EVM_ETHR_START + OMAP3EVM_ETHR_SIZE - 1),
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = OMAP_GPIO_IRQ(OMAP3EVM_ETHR_GPIO_IRQ),
- .end = OMAP_GPIO_IRQ(OMAP3EVM_ETHR_GPIO_IRQ),
- .flags = (IORESOURCE_IRQ | IRQF_TRIGGER_LOW),
- },
-};
+#include <plat/gpmc-smsc911x.h>
-static struct smsc911x_platform_config smsc911x_config = {
- .phy_interface = PHY_INTERFACE_MODE_MII,
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
- .flags = (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS),
-};
-
-static struct platform_device omap3evm_smsc911x_device = {
- .name = "smsc911x",
- .id = -1,
- .num_resources = ARRAY_SIZE(omap3evm_smsc911x_resources),
- .resource = &omap3evm_smsc911x_resources[0],
- .dev = {
- .platform_data = &smsc911x_config,
- },
+static struct omap_smsc911x_platform_data smsc911x_cfg = {
+ .cs = OMAP3EVM_SMSC911X_CS,
+ .gpio_irq = OMAP3EVM_ETHR_GPIO_IRQ,
+ .gpio_reset = -EINVAL,
+ .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
};
static inline void __init omap3evm_init_smsc911x(void)
{
- int eth_cs, eth_rst;
struct clk *l3ck;
unsigned int rate;
- if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1)
- eth_rst = OMAP3EVM_GEN1_ETHR_GPIO_RST;
- else
- eth_rst = OMAP3EVM_GEN2_ETHR_GPIO_RST;
-
- eth_cs = OMAP3EVM_SMSC911X_CS;
-
l3ck = clk_get(NULL, "l3_ck");
if (IS_ERR(l3ck))
rate = 100000000;
/* Configure ethernet controller reset gpio */
if (cpu_is_omap3430()) {
- if (gpio_request(eth_rst, "SMSC911x gpio") < 0) {
- pr_err(KERN_ERR "Failed to request %d for smsc911x\n",
- eth_rst);
- return;
- }
-
- if (gpio_direction_output(eth_rst, 1) < 0) {
- pr_err(KERN_ERR "Failed to set direction of %d for" \
- " smsc911x\n", eth_rst);
- return;
- }
- /* reset pulse to ethernet controller*/
- usleep_range(150, 220);
- gpio_set_value(eth_rst, 0);
- usleep_range(150, 220);
- gpio_set_value(eth_rst, 1);
- usleep_range(1, 2);
- }
-
- if (gpio_request(OMAP3EVM_ETHR_GPIO_IRQ, "SMSC911x irq") < 0) {
- printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n",
- OMAP3EVM_ETHR_GPIO_IRQ);
- return;
+ if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1)
+ smsc911x_cfg.gpio_reset = OMAP3EVM_GEN1_ETHR_GPIO_RST;
+ else
+ smsc911x_cfg.gpio_reset = OMAP3EVM_GEN2_ETHR_GPIO_RST;
}
- gpio_direction_input(OMAP3EVM_ETHR_GPIO_IRQ);
- platform_device_register(&omap3evm_smsc911x_device);
+ gpmc_smsc911x_init(&smsc911x_cfg);
}
#else
#define OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO 210
#define OMAP3EVM_DVI_PANEL_EN_GPIO 199
+static struct gpio omap3_evm_dss_gpios[] __initdata = {
+ { OMAP3EVM_LCD_PANEL_RESB, GPIOF_OUT_INIT_HIGH, "lcd_panel_resb" },
+ { OMAP3EVM_LCD_PANEL_INI, GPIOF_OUT_INIT_HIGH, "lcd_panel_ini" },
+ { OMAP3EVM_LCD_PANEL_QVGA, GPIOF_OUT_INIT_LOW, "lcd_panel_qvga" },
+ { OMAP3EVM_LCD_PANEL_LR, GPIOF_OUT_INIT_HIGH, "lcd_panel_lr" },
+ { OMAP3EVM_LCD_PANEL_UD, GPIOF_OUT_INIT_HIGH, "lcd_panel_ud" },
+ { OMAP3EVM_LCD_PANEL_ENVDD, GPIOF_OUT_INIT_LOW, "lcd_panel_envdd" },
+};
+
static int lcd_enabled;
static int dvi_enabled;
{
int r;
- r = gpio_request(OMAP3EVM_LCD_PANEL_RESB, "lcd_panel_resb");
- if (r) {
- printk(KERN_ERR "failed to get lcd_panel_resb\n");
- return;
- }
- gpio_direction_output(OMAP3EVM_LCD_PANEL_RESB, 1);
-
- r = gpio_request(OMAP3EVM_LCD_PANEL_INI, "lcd_panel_ini");
- if (r) {
- printk(KERN_ERR "failed to get lcd_panel_ini\n");
- goto err_1;
- }
- gpio_direction_output(OMAP3EVM_LCD_PANEL_INI, 1);
-
- r = gpio_request(OMAP3EVM_LCD_PANEL_QVGA, "lcd_panel_qvga");
- if (r) {
- printk(KERN_ERR "failed to get lcd_panel_qvga\n");
- goto err_2;
- }
- gpio_direction_output(OMAP3EVM_LCD_PANEL_QVGA, 0);
-
- r = gpio_request(OMAP3EVM_LCD_PANEL_LR, "lcd_panel_lr");
- if (r) {
- printk(KERN_ERR "failed to get lcd_panel_lr\n");
- goto err_3;
- }
- gpio_direction_output(OMAP3EVM_LCD_PANEL_LR, 1);
-
- r = gpio_request(OMAP3EVM_LCD_PANEL_UD, "lcd_panel_ud");
- if (r) {
- printk(KERN_ERR "failed to get lcd_panel_ud\n");
- goto err_4;
- }
- gpio_direction_output(OMAP3EVM_LCD_PANEL_UD, 1);
-
- r = gpio_request(OMAP3EVM_LCD_PANEL_ENVDD, "lcd_panel_envdd");
- if (r) {
- printk(KERN_ERR "failed to get lcd_panel_envdd\n");
- goto err_5;
- }
- gpio_direction_output(OMAP3EVM_LCD_PANEL_ENVDD, 0);
-
- return;
-
-err_5:
- gpio_free(OMAP3EVM_LCD_PANEL_UD);
-err_4:
- gpio_free(OMAP3EVM_LCD_PANEL_LR);
-err_3:
- gpio_free(OMAP3EVM_LCD_PANEL_QVGA);
-err_2:
- gpio_free(OMAP3EVM_LCD_PANEL_INI);
-err_1:
- gpio_free(OMAP3EVM_LCD_PANEL_RESB);
-
+ r = gpio_request_array(omap3_evm_dss_gpios,
+ ARRAY_SIZE(omap3_evm_dss_gpios));
+ if (r)
+ printk(KERN_ERR "failed to get lcd_panel_* gpios\n");
}
static int omap3_evm_enable_lcd(struct omap_dss_device *dssdev)
static int omap3evm_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
- int r;
+ int r, lcd_bl_en;
/* gpio + 0 is "mmc0_cd" (input/IRQ) */
omap_mux_init_gpio(63, OMAP_PIN_INPUT);
*/
/* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */
- r = gpio_request(gpio + TWL4030_GPIO_MAX, "EN_LCD_BKL");
- if (!r)
- r = gpio_direction_output(gpio + TWL4030_GPIO_MAX,
- (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) ? 1 : 0);
+ lcd_bl_en = get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2 ?
+ GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW;
+ r = gpio_request_one(gpio + TWL4030_GPIO_MAX, lcd_bl_en, "EN_LCD_BKL");
if (r)
printk(KERN_ERR "failed to get/set lcd_bkl gpio\n");
/* gpio + 7 == DVI Enable */
- gpio_request(gpio + 7, "EN_DVI");
- gpio_direction_output(gpio + 7, 0);
+ gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
/* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
.vdac = &omap3_evm_vdac,
.vpll2 = &omap3_evm_vpll2,
.vio = &omap3evm_vio,
-};
-
-static struct i2c_board_info __initdata omap3evm_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("twl4030", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &omap3evm_twldata,
- },
+ .vmmc1 = &omap3evm_vmmc1,
+ .vsim = &omap3evm_vsim,
};
static int __init omap3_evm_i2c_init(void)
{
- /*
- * REVISIT: These entries can be set in omap3evm_twl_data
- * after a merge with MFD tree
- */
- omap3evm_twldata.vmmc1 = &omap3evm_vmmc1;
- omap3evm_twldata.vsim = &omap3evm_vsim;
-
- omap_register_i2c_bus(1, 2600, omap3evm_i2c_boardinfo,
- ARRAY_SIZE(omap3evm_i2c_boardinfo));
+ omap3_pmic_init("twl4030", &omap3evm_twldata);
omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(3, 400, NULL, 0);
return 0;
}
-static void ads7846_dev_init(void)
-{
- if (gpio_request(OMAP3_EVM_TS_GPIO, "ADS7846 pendown") < 0)
- printk(KERN_ERR "can't get ads7846 pen down GPIO\n");
-
- gpio_direction_input(OMAP3_EVM_TS_GPIO);
- gpio_set_debounce(OMAP3_EVM_TS_GPIO, 310);
-}
-
-static int ads7846_get_pendown_state(void)
-{
- return !gpio_get_value(OMAP3_EVM_TS_GPIO);
-}
-
-static struct ads7846_platform_data ads7846_config = {
- .x_max = 0x0fff,
- .y_max = 0x0fff,
- .x_plate_ohms = 180,
- .pressure_max = 255,
- .debounce_max = 10,
- .debounce_tol = 3,
- .debounce_rep = 1,
- .get_pendown_state = ads7846_get_pendown_state,
- .keep_vref_on = 1,
- .settle_delay_usecs = 150,
- .wakeup = true,
-};
-
-static struct omap2_mcspi_device_config ads7846_mcspi_config = {
- .turbo_mode = 0,
- .single_channel = 1, /* 0: slave, 1: master */
-};
-
-static struct spi_board_info omap3evm_spi_board_info[] = {
- [0] = {
- .modalias = "ads7846",
- .bus_num = 1,
- .chip_select = 0,
- .max_speed_hz = 1500000,
- .controller_data = &ads7846_mcspi_config,
- .irq = OMAP_GPIO_IRQ(OMAP3_EVM_TS_GPIO),
- .platform_data = &ads7846_config,
- },
-};
-
static struct omap_board_config_kernel omap3_evm_config[] __initdata = {
};
.power = 100,
};
+static struct gpio omap3_evm_ehci_gpios[] __initdata = {
+ { OMAP3_EVM_EHCI_VBUS, GPIOF_OUT_INIT_HIGH, "enable EHCI VBUS" },
+ { OMAP3_EVM_EHCI_SELECT, GPIOF_OUT_INIT_LOW, "select EHCI port" },
+};
+
static void __init omap3_evm_init(void)
{
omap3_evm_get_revision();
omap_display_init(&omap3_evm_dss_data);
- spi_register_board_info(omap3evm_spi_board_info,
- ARRAY_SIZE(omap3evm_spi_board_info));
-
omap_serial_init();
/* OMAP3EVM uses ISP1504 phy and so register nop transceiver */
if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) {
/* enable EHCI VBUS using GPIO22 */
- omap_mux_init_gpio(22, OMAP_PIN_INPUT_PULLUP);
- gpio_request(OMAP3_EVM_EHCI_VBUS, "enable EHCI VBUS");
- gpio_direction_output(OMAP3_EVM_EHCI_VBUS, 0);
- gpio_set_value(OMAP3_EVM_EHCI_VBUS, 1);
-
+ omap_mux_init_gpio(OMAP3_EVM_EHCI_VBUS, OMAP_PIN_INPUT_PULLUP);
/* Select EHCI port on main board */
- omap_mux_init_gpio(61, OMAP_PIN_INPUT_PULLUP);
- gpio_request(OMAP3_EVM_EHCI_SELECT, "select EHCI port");
- gpio_direction_output(OMAP3_EVM_EHCI_SELECT, 0);
- gpio_set_value(OMAP3_EVM_EHCI_SELECT, 0);
+ omap_mux_init_gpio(OMAP3_EVM_EHCI_SELECT,
+ OMAP_PIN_INPUT_PULLUP);
+ gpio_request_array(omap3_evm_ehci_gpios,
+ ARRAY_SIZE(omap3_evm_ehci_gpios));
/* setup EHCI phy reset config */
omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP);
}
usb_musb_init(&musb_board_data);
usbhs_init(&usbhs_bdata);
- ads7846_dev_init();
+ omap_ads7846_init(1, OMAP3_EVM_TS_GPIO, 310, NULL);
omap3evm_init_smsc911x();
omap3_evm_display_init();
git.openpandora.org / pandora-kernel.git / blobdiff