#include "hsmmc.h"
#include "timer-gp.h"
#include "pm.h"
-
-#define NAND_BLOCK_SIZE SZ_128K
+#include "common-board-devices.h"
/*
* OMAP3 Beagle revision
return omap3_beagle_version;
}
+static struct gpio omap3_beagle_rev_gpios[] __initdata = {
+ { 171, GPIOF_IN, "rev_id_0" },
+ { 172, GPIOF_IN, "rev_id_1" },
+ { 173, GPIOF_IN, "rev_id_2" },
+};
+
static void __init omap3_beagle_init_rev(void)
{
int ret;
omap_mux_init_gpio(172, OMAP_PIN_INPUT_PULLUP);
omap_mux_init_gpio(173, OMAP_PIN_INPUT_PULLUP);
- ret = gpio_request(171, "rev_id_0");
- if (ret < 0)
- goto fail0;
-
- ret = gpio_request(172, "rev_id_1");
- if (ret < 0)
- goto fail1;
-
- ret = gpio_request(173, "rev_id_2");
- if (ret < 0)
- goto fail2;
-
- gpio_direction_input(171);
- gpio_direction_input(172);
- gpio_direction_input(173);
+ ret = gpio_request_array(omap3_beagle_rev_gpios,
+ ARRAY_SIZE(omap3_beagle_rev_gpios));
+ if (ret < 0) {
+ printk(KERN_ERR "Unable to get revision detection GPIO pins\n");
+ omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
+ return;
+ }
beagle_rev = gpio_get_value(171) | (gpio_get_value(172) << 1)
| (gpio_get_value(173) << 2);
+ gpio_free_array(omap3_beagle_rev_gpios,
+ ARRAY_SIZE(omap3_beagle_rev_gpios));
+
switch (beagle_rev) {
case 7:
printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n");
printk(KERN_INFO "OMAP3 Beagle Rev: unknown %hd\n", beagle_rev);
omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
}
-
- return;
-
-fail2:
- gpio_free(172);
-fail1:
- gpio_free(171);
-fail0:
- printk(KERN_ERR "Unable to get revision detection GPIO pins\n");
- omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
-
- return;
}
static struct mtd_partition omap3beagle_nand_partitions[] = {
},
};
-static struct omap_nand_platform_data omap3beagle_nand_data = {
- .options = NAND_BUSWIDTH_16,
- .parts = omap3beagle_nand_partitions,
- .nr_parts = ARRAY_SIZE(omap3beagle_nand_partitions),
- .dma_channel = -1, /* disable DMA in OMAP NAND driver */
- .nand_setup = NULL,
- .dev_ready = NULL,
-};
-
/* DSS */
static int beagle_enable_dvi(struct omap_dss_device *dssdev)
{
int r;
- r = gpio_request(beagle_dvi_device.reset_gpio, "DVI reset");
- if (r < 0) {
+ r = gpio_request_one(beagle_dvi_device.reset_gpio, GPIOF_OUT_INIT_LOW,
+ "DVI reset");
+ if (r < 0)
printk(KERN_ERR "Unable to get DVI reset GPIO\n");
- return;
- }
-
- gpio_direction_output(beagle_dvi_device.reset_gpio, 0);
}
#include "sdram-micron-mt46h32m32lf-6.h"
static int beagle_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
- int r;
+ int r, usb_pwr_level;
if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
mmc[0].gpio_wp = -EINVAL;
beagle_vmmc1_supply.dev = mmc[0].dev;
beagle_vsim_supply.dev = mmc[0].dev;
- /* REVISIT: need ehci-omap hooks for external VBUS
- * power switch and overcurrent detect
- */
- if (omap3_beagle_get_rev() != OMAP3BEAGLE_BOARD_XM) {
- r = gpio_request(gpio + 1, "EHCI_nOC");
- if (!r) {
- r = gpio_direction_input(gpio + 1);
- if (r)
- gpio_free(gpio + 1);
- }
- if (r)
- pr_err("%s: unable to configure EHCI_nOC\n", __func__);
- }
-
/*
* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, XM active
* high / others active low)
- */
- gpio_request(gpio + TWL4030_GPIO_MAX, "nEN_USB_PWR");
- if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM)
- gpio_direction_output(gpio + TWL4030_GPIO_MAX, 1);
- else
- gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0);
-
- /* DVI reset GPIO is different between beagle revisions */
- if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM)
- beagle_dvi_device.reset_gpio = 129;
- else
- beagle_dvi_device.reset_gpio = 170;
-
- /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
- gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
-
- /*
- * gpio + 1 on Xm controls the TFP410's enable line (active low)
- * gpio + 2 control varies depending on the board rev as follows:
- * P7/P8 revisions(prototype): Camera EN
- * A2+ revisions (production): LDO (supplies DVI, serial, led blocks)
+ * DVI reset GPIO is different between beagle revisions
*/
if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
- r = gpio_request(gpio + 1, "nDVI_PWR_EN");
- if (!r) {
- r = gpio_direction_output(gpio + 1, 0);
- if (r)
- gpio_free(gpio + 1);
- }
+ usb_pwr_level = GPIOF_OUT_INIT_HIGH;
+ beagle_dvi_device.reset_gpio = 129;
+ /*
+ * gpio + 1 on Xm controls the TFP410's enable line (active low)
+ * gpio + 2 control varies depending on the board rev as below:
+ * P7/P8 revisions(prototype): Camera EN
+ * A2+ revisions (production): LDO (DVI, serial, led blocks)
+ */
+ r = gpio_request_one(gpio + 1, GPIOF_OUT_INIT_LOW,
+ "nDVI_PWR_EN");
if (r)
pr_err("%s: unable to configure nDVI_PWR_EN\n",
__func__);
- r = gpio_request(gpio + 2, "DVI_LDO_EN");
- if (!r) {
- r = gpio_direction_output(gpio + 2, 1);
- if (r)
- gpio_free(gpio + 2);
- }
+ r = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_HIGH,
+ "DVI_LDO_EN");
if (r)
pr_err("%s: unable to configure DVI_LDO_EN\n",
__func__);
+ } else {
+ usb_pwr_level = GPIOF_OUT_INIT_LOW;
+ beagle_dvi_device.reset_gpio = 170;
+ /*
+ * REVISIT: need ehci-omap hooks for external VBUS
+ * power switch and overcurrent detect
+ */
+ if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC"))
+ pr_err("%s: unable to configure EHCI_nOC\n", __func__);
}
+ gpio_request_one(gpio + TWL4030_GPIO_MAX, usb_pwr_level, "nEN_USB_PWR");
+
+ /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
+ gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
+
return 0;
}
.vpll2 = &beagle_vpll2,
};
-static struct i2c_board_info __initdata beagle_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("twl4030", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &beagle_twldata,
- },
-};
-
static struct i2c_board_info __initdata beagle_i2c_eeprom[] = {
{
I2C_BOARD_INFO("eeprom", 0x50),
static int __init omap3_beagle_i2c_init(void)
{
- omap_register_i2c_bus(1, 2600, beagle_i2c_boardinfo,
- ARRAY_SIZE(beagle_i2c_boardinfo));
+ omap3_pmic_init("twl4030", &beagle_twldata);
/* Bus 3 is attached to the DVI port where devices like the pico DLP
* projector don't work reliably with 400kHz */
omap_register_i2c_bus(3, 100, beagle_i2c_eeprom, ARRAY_SIZE(beagle_i2c_eeprom));
&keys_gpio,
};
-static void __init omap3beagle_flash_init(void)
-{
- u8 cs = 0;
- u8 nandcs = GPMC_CS_NUM + 1;
-
- /* find out the chip-select on which NAND exists */
- while (cs < GPMC_CS_NUM) {
- u32 ret = 0;
- ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
-
- if ((ret & 0xC00) == 0x800) {
- printk(KERN_INFO "Found NAND on CS%d\n", cs);
- if (nandcs > GPMC_CS_NUM)
- nandcs = cs;
- }
- cs++;
- }
-
- if (nandcs > GPMC_CS_NUM) {
- printk(KERN_INFO "NAND: Unable to find configuration "
- "in GPMC\n ");
- return;
- }
-
- if (nandcs < GPMC_CS_NUM) {
- omap3beagle_nand_data.cs = nandcs;
-
- printk(KERN_INFO "Registering NAND on CS%d\n", nandcs);
- if (gpmc_nand_init(&omap3beagle_nand_data) < 0)
- printk(KERN_ERR "Unable to register NAND device\n");
- }
-}
-
static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
};
#endif
-static struct omap_musb_board_data musb_board_data = {
- .interface_type = MUSB_INTERFACE_ULPI,
- .mode = MUSB_OTG,
- .power = 100,
-};
-
static void __init beagle_opp_init(void)
{
int r = 0;
omap_serial_init();
omap_mux_init_gpio(170, OMAP_PIN_INPUT);
- gpio_request(170, "DVI_nPD");
/* REVISIT leave DVI powered down until it's needed ... */
- gpio_direction_output(170, true);
+ gpio_request_one(170, GPIOF_OUT_INIT_HIGH, "DVI_nPD");
- usb_musb_init(&musb_board_data);
+ usb_musb_init(NULL);
usbhs_init(&usbhs_bdata);
- omap3beagle_flash_init();
+ omap_nand_flash_init(NAND_BUSWIDTH_16, omap3beagle_nand_partitions,
+ ARRAY_SIZE(omap3beagle_nand_partitions));
+
+ /* Ensure msecure is mux'd to be able to set the RTC. */
+ omap_mux_init_signal("sys_drm_msecure", OMAP_PIN_OFF_OUTPUT_HIGH);
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
git.openpandora.org / pandora-kernel.git / blobdiff