Merge branch 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6

[pandora-kernel.git] / arch / arm / mach-omap2 / board-n8x0.c

diff --git a/arch/arm/mach-omap2/board-n8x0.c b/arch/arm/mach-omap2/board-n8x0.c
index e823c70..f396756 100644 (file)
--- a/arch/arm/mach-omap2/board-n8x0.c
+++ b/arch/arm/mach-omap2/board-n8x0.c
@@ -46,8 +46,7 @@ static struct device *mmc_device;
 #define TUSB6010_GPIO_ENABLE   0
 #define TUSB6010_DMACHAN       0x3f
 
-#if defined(CONFIG_USB_TUSB6010) || \
-       defined(CONFIG_USB_TUSB6010_MODULE)
+#ifdef CONFIG_USB_MUSB_TUSB6010
 /*
  * Enable or disable power to TUSB6010. When enabling, turn on 3.3 V and
  * 1.5 V voltage regulators of PM companion chip. Companion chip will then
@@ -134,7 +133,7 @@ err:
 
 static void __init n8x0_usb_init(void) {}
 
-#endif /*CONFIG_USB_TUSB6010 */
+#endif /*CONFIG_USB_MUSB_TUSB6010 */
 
 
 static struct omap2_mcspi_device_config p54spi_mcspi_config = {
@@ -184,23 +183,15 @@ static struct mtd_partition onenand_partitions[] = {
        },
 };
 
-static struct omap_onenand_platform_data board_onenand_data = {
-       .cs             = 0,
-       .gpio_irq       = 26,
-       .parts          = onenand_partitions,
-       .nr_parts       = ARRAY_SIZE(onenand_partitions),
-       .flags          = ONENAND_SYNC_READ,
+static struct omap_onenand_platform_data board_onenand_data[] = {
+       {
+               .cs             = 0,
+               .gpio_irq       = 26,
+               .parts          = onenand_partitions,
+               .nr_parts       = ARRAY_SIZE(onenand_partitions),
+               .flags          = ONENAND_SYNC_READ,
+       }
 };
-
-static void __init n8x0_onenand_init(void)
-{
-       gpmc_onenand_init(&board_onenand_data);
-}
-
-#else
-
-static void __init n8x0_onenand_init(void) {}
-
 #endif
 
 #if defined(CONFIG_MENELAUS) &&                                                \
@@ -639,9 +630,9 @@ static void __init n8x0_map_io(void)
 
 static void __init n8x0_init_irq(void)
 {
-       omap2_init_common_hw(NULL, NULL);
+       omap2_init_common_infrastructure();
+       omap2_init_common_devices(NULL, NULL);
        omap_init_irq();
-       omap_gpio_init();
 }
 
 #ifdef CONFIG_OMAP_MUX
@@ -653,8 +644,43 @@ static struct omap_board_mux board_mux[] __initdata = {
        OMAP2420_MUX(EAC_AC_DOUT, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
        { .reg_offset = OMAP_MUX_TERMINATOR },
 };
+
+static struct omap_device_pad serial2_pads[] __initdata = {
+       {
+               .name   = "uart3_rx_irrx.uart3_rx_irrx",
+               .flags  = OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
+               .enable = OMAP_MUX_MODE0,
+               .idle   = OMAP_MUX_MODE3        /* Mux as GPIO for idle */
+       },
+};
+
+static inline void board_serial_init(void)
+{
+       struct omap_board_data bdata;
+
+       bdata.flags = 0;
+       bdata.pads = NULL;
+       bdata.pads_cnt = 0;
+
+       bdata.id = 0;
+       omap_serial_init_port(&bdata);
+
+       bdata.id = 1;
+       omap_serial_init_port(&bdata);
+
+       bdata.id = 2;
+       bdata.pads = serial2_pads;
+       bdata.pads_cnt = ARRAY_SIZE(serial2_pads);
+       omap_serial_init_port(&bdata);
+}
+
 #else
-#define board_mux      NULL
+
+static inline void board_serial_init(void)
+{
+       omap_serial_init();
+}
+
 #endif
 
 static void __init n8x0_init_machine(void)
@@ -669,9 +695,8 @@ static void __init n8x0_init_machine(void)
        if (machine_is_nokia_n810())
                i2c_register_board_info(2, n810_i2c_board_info_2,
                                        ARRAY_SIZE(n810_i2c_board_info_2));
-
-       omap_serial_init();
-       n8x0_onenand_init();
+       board_serial_init();
+       gpmc_onenand_init(board_onenand_data);
        n8x0_mmc_init();
        n8x0_usb_init();
 }