#include <plat/common.h>
#include <plat/gpmc.h>
#include <plat/usb.h>
-#include <plat/display.h>
-#include <plat/panel-generic-dpi.h>
+#include <video/omapdss.h>
+#include <video/omap-panel-generic-dpi.h>
#include <plat/onenand.h>
#include "mux.h"
#include "hsmmc.h"
#include "sdram-numonyx-m65kxxxxam.h"
+#include "common-board-devices.h"
#define IGEP2_SMSC911X_CS 5
#define IGEP2_SMSC911X_GPIO 176
#define IGEP2_RC_GPIO_WIFI_NRESET 139
#define IGEP2_RC_GPIO_BT_NRESET 137
+#define IGEP3_GPIO_LED0_GREEN 54
+#define IGEP3_GPIO_LED0_RED 53
+#define IGEP3_GPIO_LED1_RED 16
+#define IGEP3_GPIO_USBH_NRESET 183
+
/*
* IGEP2 Hardware Revision Table
*
#define IGEP2_BOARD_HWREV_B 0
#define IGEP2_BOARD_HWREV_C 1
+#define IGEP3_BOARD_HWREV 2
static u8 hwrev;
{
u8 ret;
+ if (machine_is_igep0030()) {
+ hwrev = IGEP3_BOARD_HWREV;
+ return;
+ }
+
omap_mux_init_gpio(IGEP2_GPIO_LED1_RED, OMAP_PIN_INPUT);
- if ((gpio_request(IGEP2_GPIO_LED1_RED, "GPIO_HW0_REV") == 0) &&
- (gpio_direction_input(IGEP2_GPIO_LED1_RED) == 0)) {
- ret = gpio_get_value(IGEP2_GPIO_LED1_RED);
- if (ret == 0) {
- pr_info("IGEP2: Hardware Revision C (B-NON compatible)\n");
- hwrev = IGEP2_BOARD_HWREV_C;
- } else if (ret == 1) {
- pr_info("IGEP2: Hardware Revision B/C (B compatible)\n");
- hwrev = IGEP2_BOARD_HWREV_B;
- } else {
- pr_err("IGEP2: Unknown Hardware Revision\n");
- hwrev = -1;
- }
- } else {
+ if (gpio_request_one(IGEP2_GPIO_LED1_RED, GPIOF_IN, "GPIO_HW0_REV")) {
pr_warning("IGEP2: Could not obtain gpio GPIO_HW0_REV\n");
pr_err("IGEP2: Unknown Hardware Revision\n");
+ return;
+ }
+
+ ret = gpio_get_value(IGEP2_GPIO_LED1_RED);
+ if (ret == 0) {
+ pr_info("IGEP2: Hardware Revision C (B-NON compatible)\n");
+ hwrev = IGEP2_BOARD_HWREV_C;
+ } else if (ret == 1) {
+ pr_info("IGEP2: Hardware Revision B/C (B compatible)\n");
+ hwrev = IGEP2_BOARD_HWREV_B;
+ } else {
+ pr_err("IGEP2: Unknown Hardware Revision\n");
+ hwrev = -1;
}
gpio_free(IGEP2_GPIO_LED1_RED);
* So MTD regards it as 4KiB page size and 256KiB block size 64*(2*2048)
*/
-static struct mtd_partition igep2_onenand_partitions[] = {
+static struct mtd_partition igep_onenand_partitions[] = {
{
.name = "X-Loader",
.offset = 0,
},
};
-static struct omap_onenand_platform_data igep2_onenand_data = {
- .parts = igep2_onenand_partitions,
- .nr_parts = ARRAY_SIZE(igep2_onenand_partitions),
+static struct omap_onenand_platform_data igep_onenand_data = {
+ .parts = igep_onenand_partitions,
+ .nr_parts = ARRAY_SIZE(igep_onenand_partitions),
.dma_channel = -1, /* disable DMA in OMAP OneNAND driver */
};
-static struct platform_device igep2_onenand_device = {
+static struct platform_device igep_onenand_device = {
.name = "omap2-onenand",
.id = -1,
.dev = {
- .platform_data = &igep2_onenand_data,
+ .platform_data = &igep_onenand_data,
},
};
-static void __init igep2_flash_init(void)
+static void __init igep_flash_init(void)
{
u8 cs = 0;
u8 onenandcs = GPMC_CS_NUM + 1;
/* Check if NAND/oneNAND is configured */
if ((ret & 0xC00) == 0x800)
/* NAND found */
- pr_err("IGEP2: Unsupported NAND found\n");
+ pr_err("IGEP: Unsupported NAND found\n");
else {
ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG7);
if ((ret & 0x3F) == (ONENAND_MAP >> 24))
}
if (onenandcs > GPMC_CS_NUM) {
- pr_err("IGEP2: Unable to find configuration in GPMC\n");
+ pr_err("IGEP: Unable to find configuration in GPMC\n");
return;
}
- igep2_onenand_data.cs = onenandcs;
+ igep_onenand_data.cs = onenandcs;
- if (platform_device_register(&igep2_onenand_device) < 0)
- pr_err("IGEP2: Unable to register OneNAND device\n");
+ if (platform_device_register(&igep_onenand_device) < 0)
+ pr_err("IGEP: Unable to register OneNAND device\n");
}
#else
-static void __init igep2_flash_init(void) {}
+static void __init igep_flash_init(void) {}
#endif
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
#include <linux/smsc911x.h>
+#include <plat/gpmc-smsc911x.h>
-static struct smsc911x_platform_config igep2_smsc911x_config = {
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
- .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS ,
- .phy_interface = PHY_INTERFACE_MODE_MII,
-};
-
-static struct resource igep2_smsc911x_resources[] = {
- {
- .flags = IORESOURCE_MEM,
- },
- {
- .start = OMAP_GPIO_IRQ(IGEP2_SMSC911X_GPIO),
- .end = OMAP_GPIO_IRQ(IGEP2_SMSC911X_GPIO),
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
- },
-};
-
-static struct platform_device igep2_smsc911x_device = {
- .name = "smsc911x",
- .id = 0,
- .num_resources = ARRAY_SIZE(igep2_smsc911x_resources),
- .resource = igep2_smsc911x_resources,
- .dev = {
- .platform_data = &igep2_smsc911x_config,
- },
+static struct omap_smsc911x_platform_data smsc911x_cfg = {
+ .cs = IGEP2_SMSC911X_CS,
+ .gpio_irq = IGEP2_SMSC911X_GPIO,
+ .gpio_reset = -EINVAL,
+ .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
};
static inline void __init igep2_init_smsc911x(void)
{
- unsigned long cs_mem_base;
-
- if (gpmc_cs_request(IGEP2_SMSC911X_CS, SZ_16M, &cs_mem_base) < 0) {
- pr_err("IGEP v2: Failed request for GPMC mem for smsc911x\n");
- gpmc_cs_free(IGEP2_SMSC911X_CS);
- return;
- }
-
- igep2_smsc911x_resources[0].start = cs_mem_base + 0x0;
- igep2_smsc911x_resources[0].end = cs_mem_base + 0xff;
-
- if ((gpio_request(IGEP2_SMSC911X_GPIO, "SMSC911X IRQ") == 0) &&
- (gpio_direction_input(IGEP2_SMSC911X_GPIO) == 0)) {
- gpio_export(IGEP2_SMSC911X_GPIO, 0);
- } else {
- pr_err("IGEP v2: Could not obtain gpio for for SMSC911X IRQ\n");
- return;
- }
-
- platform_device_register(&igep2_smsc911x_device);
+ gpmc_smsc911x_init(&smsc911x_cfg);
}
#else
static inline void __init igep2_init_smsc911x(void) { }
#endif
-static struct regulator_consumer_supply igep2_vmmc1_supply =
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0");
+static struct regulator_consumer_supply igep_vmmc1_supply[] = {
+ REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
+};
/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
-static struct regulator_init_data igep2_vmmc1 = {
+static struct regulator_init_data igep_vmmc1 = {
.constraints = {
.min_uV = 1850000,
.max_uV = 3150000,
| REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
- .num_consumer_supplies = 1,
- .consumer_supplies = &igep2_vmmc1_supply,
+ .num_consumer_supplies = ARRAY_SIZE(igep_vmmc1_supply),
+ .consumer_supplies = igep_vmmc1_supply,
};
-static struct regulator_consumer_supply igep2_vio_supply =
- REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.1");
+static struct regulator_consumer_supply igep_vio_supply[] = {
+ REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.1"),
+};
-static struct regulator_init_data igep2_vio = {
+static struct regulator_init_data igep_vio = {
.constraints = {
.min_uV = 1800000,
.max_uV = 1800000,
| REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
- .num_consumer_supplies = 1,
- .consumer_supplies = &igep2_vio_supply,
+ .num_consumer_supplies = ARRAY_SIZE(igep_vio_supply),
+ .consumer_supplies = igep_vio_supply,
};
-static struct regulator_consumer_supply igep2_vmmc2_supply =
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1");
+static struct regulator_consumer_supply igep_vmmc2_supply[] = {
+ REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"),
+};
-static struct regulator_init_data igep2_vmmc2 = {
+static struct regulator_init_data igep_vmmc2 = {
.constraints = {
.valid_modes_mask = REGULATOR_MODE_NORMAL,
.always_on = 1,
},
- .num_consumer_supplies = 1,
- .consumer_supplies = &igep2_vmmc2_supply,
+ .num_consumer_supplies = ARRAY_SIZE(igep_vmmc2_supply),
+ .consumer_supplies = igep_vmmc2_supply,
};
-static struct fixed_voltage_config igep2_vwlan = {
+static struct fixed_voltage_config igep_vwlan = {
.supply_name = "vwlan",
.microvolts = 3300000,
.gpio = -EINVAL,
.enabled_at_boot = 1,
- .init_data = &igep2_vmmc2,
+ .init_data = &igep_vmmc2,
};
-static struct platform_device igep2_vwlan_device = {
+static struct platform_device igep_vwlan_device = {
.name = "reg-fixed-voltage",
.id = 0,
.dev = {
- .platform_data = &igep2_vwlan,
+ .platform_data = &igep_vwlan,
},
};
#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
#include <linux/leds.h>
-static struct gpio_led igep2_gpio_leds[] = {
+static struct gpio_led igep_gpio_leds[] = {
[0] = {
.name = "gpio-led:red:d0",
- .gpio = IGEP2_GPIO_LED0_RED,
.default_trigger = "default-off"
},
[1] = {
.name = "gpio-led:green:d0",
- .gpio = IGEP2_GPIO_LED0_GREEN,
.default_trigger = "default-off",
},
[2] = {
.name = "gpio-led:red:d1",
- .gpio = IGEP2_GPIO_LED1_RED,
.default_trigger = "default-off",
},
[3] = {
},
};
-static struct gpio_led_platform_data igep2_led_pdata = {
- .leds = igep2_gpio_leds,
- .num_leds = ARRAY_SIZE(igep2_gpio_leds),
+static struct gpio_led_platform_data igep_led_pdata = {
+ .leds = igep_gpio_leds,
+ .num_leds = ARRAY_SIZE(igep_gpio_leds),
};
-static struct platform_device igep2_led_device = {
+static struct platform_device igep_led_device = {
.name = "leds-gpio",
.id = -1,
.dev = {
- .platform_data = &igep2_led_pdata,
+ .platform_data = &igep_led_pdata,
},
};
-static void __init igep2_leds_init(void)
+static void __init igep_leds_init(void)
{
- platform_device_register(&igep2_led_device);
+ if (machine_is_igep0020()) {
+ igep_gpio_leds[0].gpio = IGEP2_GPIO_LED0_RED;
+ igep_gpio_leds[1].gpio = IGEP2_GPIO_LED0_GREEN;
+ igep_gpio_leds[2].gpio = IGEP2_GPIO_LED1_RED;
+ } else {
+ igep_gpio_leds[0].gpio = IGEP3_GPIO_LED0_RED;
+ igep_gpio_leds[1].gpio = IGEP3_GPIO_LED0_GREEN;
+ igep_gpio_leds[2].gpio = IGEP3_GPIO_LED1_RED;
+ }
+
+ platform_device_register(&igep_led_device);
}
#else
-static inline void igep2_leds_init(void)
+static struct gpio igep_gpio_leds[] __initdata = {
+ { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:red:d0" },
+ { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:green:d0" },
+ { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:red:d1" },
+};
+
+static inline void igep_leds_init(void)
{
- if ((gpio_request(IGEP2_GPIO_LED0_RED, "gpio-led:red:d0") == 0) &&
- (gpio_direction_output(IGEP2_GPIO_LED0_RED, 0) == 0))
- gpio_export(IGEP2_GPIO_LED0_RED, 0);
- else
- pr_warning("IGEP v2: Could not obtain gpio GPIO_LED0_RED\n");
+ int i;
- if ((gpio_request(IGEP2_GPIO_LED0_GREEN, "gpio-led:green:d0") == 0) &&
- (gpio_direction_output(IGEP2_GPIO_LED0_GREEN, 0) == 0))
- gpio_export(IGEP2_GPIO_LED0_GREEN, 0);
- else
- pr_warning("IGEP v2: Could not obtain gpio GPIO_LED0_GREEN\n");
+ if (machine_is_igep0020()) {
+ igep_gpio_leds[0].gpio = IGEP2_GPIO_LED0_RED;
+ igep_gpio_leds[1].gpio = IGEP2_GPIO_LED0_GREEN;
+ igep_gpio_leds[2].gpio = IGEP2_GPIO_LED1_RED;
+ } else {
+ igep_gpio_leds[0].gpio = IGEP3_GPIO_LED0_RED;
+ igep_gpio_leds[1].gpio = IGEP3_GPIO_LED0_GREEN;
+ igep_gpio_leds[2].gpio = IGEP3_GPIO_LED1_RED;
+ }
- if ((gpio_request(IGEP2_GPIO_LED1_RED, "gpio-led:red:d1") == 0) &&
- (gpio_direction_output(IGEP2_GPIO_LED1_RED, 0) == 0))
- gpio_export(IGEP2_GPIO_LED1_RED, 0);
- else
- pr_warning("IGEP v2: Could not obtain gpio GPIO_LED1_RED\n");
+ if (gpio_request_array(igep_gpio_leds, ARRAY_SIZE(igep_gpio_leds))) {
+ pr_warning("IGEP v2: Could not obtain leds gpios\n");
+ return;
+ }
+ for (i = 0; i < ARRAY_SIZE(igep_gpio_leds); i++)
+ gpio_export(igep_gpio_leds[i].gpio, 0);
}
#endif
-static int igep2_twl_gpio_setup(struct device *dev,
+static struct gpio igep2_twl_gpios[] = {
+ { -EINVAL, GPIOF_IN, "GPIO_EHCI_NOC" },
+ { -EINVAL, GPIOF_OUT_INIT_LOW, "GPIO_USBH_CPEN" },
+};
+
+static int igep_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
+ int ret;
+
/* gpio + 0 is "mmc0_cd" (input/IRQ) */
mmc[0].gpio_cd = gpio + 0;
omap2_hsmmc_init(mmc);
- /*
- * REVISIT: need ehci-omap hooks for external VBUS
- * power switch and overcurrent detect
- */
- if ((gpio_request(gpio + 1, "GPIO_EHCI_NOC") < 0) ||
- (gpio_direction_input(gpio + 1) < 0))
- pr_err("IGEP2: Could not obtain gpio for EHCI NOC");
-
- /*
- * TWL4030_GPIO_MAX + 0 == ledA, GPIO_USBH_CPEN
- * (out, active low)
- */
- if ((gpio_request(gpio + TWL4030_GPIO_MAX, "GPIO_USBH_CPEN") < 0) ||
- (gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0) < 0))
- pr_err("IGEP2: Could not obtain gpio for USBH_CPEN");
-
/* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
#if !defined(CONFIG_LEDS_GPIO) && !defined(CONFIG_LEDS_GPIO_MODULE)
- if ((gpio_request(gpio+TWL4030_GPIO_MAX+1, "gpio-led:green:d1") == 0)
- && (gpio_direction_output(gpio + TWL4030_GPIO_MAX + 1, 1) == 0))
+ ret = gpio_request_one(gpio + TWL4030_GPIO_MAX + 1, GPIOF_OUT_INIT_HIGH,
+ "gpio-led:green:d1");
+ if (ret == 0)
gpio_export(gpio + TWL4030_GPIO_MAX + 1, 0);
else
- pr_warning("IGEP v2: Could not obtain gpio GPIO_LED1_GREEN\n");
+ pr_warning("IGEP: Could not obtain gpio GPIO_LED1_GREEN\n");
#else
- igep2_gpio_leds[3].gpio = gpio + TWL4030_GPIO_MAX + 1;
+ igep_gpio_leds[3].gpio = gpio + TWL4030_GPIO_MAX + 1;
#endif
+ if (machine_is_igep0030())
+ return 0;
+
+ /*
+ * REVISIT: need ehci-omap hooks for external VBUS
+ * power switch and overcurrent detect
+ */
+ igep2_twl_gpios[0].gpio = gpio + 1;
+
+ /* TWL4030_GPIO_MAX + 0 == ledA, GPIO_USBH_CPEN (out, active low) */
+ igep2_twl_gpios[1].gpio = gpio + TWL4030_GPIO_MAX;
+
+ ret = gpio_request_array(igep2_twl_gpios, ARRAY_SIZE(igep2_twl_gpios));
+ if (ret < 0)
+ pr_err("IGEP2: Could not obtain gpio for USBH_CPEN");
+
return 0;
};
-static struct twl4030_gpio_platform_data igep2_twl4030_gpio_pdata = {
+static struct twl4030_gpio_platform_data igep_twl4030_gpio_pdata = {
.gpio_base = OMAP_MAX_GPIO_LINES,
.irq_base = TWL4030_GPIO_IRQ_BASE,
.irq_end = TWL4030_GPIO_IRQ_END,
.use_leds = true,
- .setup = igep2_twl_gpio_setup,
-};
-
-static struct twl4030_usb_data igep2_usb_data = {
- .usb_mode = T2_USB_MODE_ULPI,
+ .setup = igep_twl_gpio_setup,
};
static int igep2_enable_dvi(struct omap_dss_device *dssdev)
.default_device = &igep2_dvi_device,
};
-static struct regulator_consumer_supply igep2_vpll2_supplies[] = {
- REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi1"),
-};
-
-static struct regulator_init_data igep2_vpll2 = {
- .constraints = {
- .name = "VDVI",
- .min_uV = 1800000,
- .max_uV = 1800000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(igep2_vpll2_supplies),
- .consumer_supplies = igep2_vpll2_supplies,
-};
-
static void __init igep2_display_init(void)
{
- if (gpio_request(IGEP2_GPIO_DVI_PUP, "GPIO_DVI_PUP") &&
- gpio_direction_output(IGEP2_GPIO_DVI_PUP, 1))
+ int err = gpio_request_one(IGEP2_GPIO_DVI_PUP, GPIOF_OUT_INIT_HIGH,
+ "GPIO_DVI_PUP");
+ if (err)
pr_err("IGEP v2: Could not obtain gpio GPIO_DVI_PUP\n");
}
-static struct platform_device *igep2_devices[] __initdata = {
- &igep2_vwlan_device,
+static struct platform_device *igep_devices[] __initdata = {
+ &igep_vwlan_device,
};
-static void __init igep2_init_early(void)
+static void __init igep_init_early(void)
{
omap2_init_common_infrastructure();
omap2_init_common_devices(m65kxxxxam_sdrc_params,
m65kxxxxam_sdrc_params);
}
-static struct twl4030_codec_audio_data igep2_audio_data;
-
-static struct twl4030_codec_data igep2_codec_data = {
- .audio_mclk = 26000000,
- .audio = &igep2_audio_data,
-};
-
static int igep2_keymap[] = {
KEY(0, 0, KEY_LEFT),
KEY(0, 1, KEY_RIGHT),
.rep = 1,
};
-static struct twl4030_platform_data igep2_twldata = {
- .irq_base = TWL4030_IRQ_BASE,
- .irq_end = TWL4030_IRQ_END,
-
+static struct twl4030_platform_data igep_twldata = {
/* platform_data for children goes here */
- .usb = &igep2_usb_data,
- .codec = &igep2_codec_data,
- .gpio = &igep2_twl4030_gpio_pdata,
- .keypad = &igep2_keypad_pdata,
- .vmmc1 = &igep2_vmmc1,
- .vpll2 = &igep2_vpll2,
- .vio = &igep2_vio,
-};
-
-static struct i2c_board_info __initdata igep2_i2c1_boardinfo[] = {
- {
- I2C_BOARD_INFO("twl4030", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &igep2_twldata,
- },
+ .gpio = &igep_twl4030_gpio_pdata,
+ .vmmc1 = &igep_vmmc1,
+ .vio = &igep_vio,
};
static struct i2c_board_info __initdata igep2_i2c3_boardinfo[] = {
},
};
-static void __init igep2_i2c_init(void)
+static void __init igep_i2c_init(void)
{
int ret;
- ret = omap_register_i2c_bus(1, 2600, igep2_i2c1_boardinfo,
- ARRAY_SIZE(igep2_i2c1_boardinfo));
- if (ret)
- pr_warning("IGEP2: Could not register I2C1 bus (%d)\n", ret);
+ omap3_pmic_get_config(&igep_twldata, TWL_COMMON_PDATA_USB, 0);
+
+ if (machine_is_igep0020()) {
+ /*
+ * Bus 3 is attached to the DVI port where devices like the
+ * pico DLP projector don't work reliably with 400kHz
+ */
+ ret = omap_register_i2c_bus(3, 100, igep2_i2c3_boardinfo,
+ ARRAY_SIZE(igep2_i2c3_boardinfo));
+ if (ret)
+ pr_warning("IGEP2: Could not register I2C3 bus (%d)\n", ret);
+
+ igep_twldata.keypad = &igep2_keypad_pdata;
+ /* Get common pmic data */
+ omap3_pmic_get_config(&igep_twldata, TWL_COMMON_PDATA_AUDIO,
+ TWL_COMMON_REGULATOR_VPLL2);
+ igep_twldata.vpll2->constraints.apply_uV = true;
+ igep_twldata.vpll2->constraints.name = "VDVI";
+ }
- /*
- * Bus 3 is attached to the DVI port where devices like the pico DLP
- * projector don't work reliably with 400kHz
- */
- ret = omap_register_i2c_bus(3, 100, igep2_i2c3_boardinfo,
- ARRAY_SIZE(igep2_i2c3_boardinfo));
- if (ret)
- pr_warning("IGEP2: Could not register I2C3 bus (%d)\n", ret);
+ omap3_pmic_init("twl4030", &igep_twldata);
}
-static struct omap_musb_board_data musb_board_data = {
- .interface_type = MUSB_INTERFACE_ULPI,
- .mode = MUSB_OTG,
- .power = 100,
-};
-
-static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
+static const struct usbhs_omap_board_data igep2_usbhs_bdata __initconst = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.reset_gpio_port[2] = -EINVAL,
};
+static const struct usbhs_omap_board_data igep3_usbhs_bdata __initconst = {
+ .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
+
+ .phy_reset = true,
+ .reset_gpio_port[0] = -EINVAL,
+ .reset_gpio_port[1] = IGEP3_GPIO_USBH_NRESET,
+ .reset_gpio_port[2] = -EINVAL,
+};
+
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
{ .reg_offset = OMAP_MUX_TERMINATOR },
#endif
#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
+static struct gpio igep_wlan_bt_gpios[] __initdata = {
+ { -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_WIFI_NPD" },
+ { -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_WIFI_NRESET" },
+ { -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_BT_NRESET" },
+};
-static void __init igep2_wlan_bt_init(void)
+static void __init igep_wlan_bt_init(void)
{
- unsigned npd, wreset, btreset;
+ int err;
/* GPIO's for WLAN-BT combo depends on hardware revision */
if (hwrev == IGEP2_BOARD_HWREV_B) {
- npd = IGEP2_RB_GPIO_WIFI_NPD;
- wreset = IGEP2_RB_GPIO_WIFI_NRESET;
- btreset = IGEP2_RB_GPIO_BT_NRESET;
- } else if (hwrev == IGEP2_BOARD_HWREV_C) {
- npd = IGEP2_RC_GPIO_WIFI_NPD;
- wreset = IGEP2_RC_GPIO_WIFI_NRESET;
- btreset = IGEP2_RC_GPIO_BT_NRESET;
+ igep_wlan_bt_gpios[0].gpio = IGEP2_RB_GPIO_WIFI_NPD;
+ igep_wlan_bt_gpios[1].gpio = IGEP2_RB_GPIO_WIFI_NRESET;
+ igep_wlan_bt_gpios[2].gpio = IGEP2_RB_GPIO_BT_NRESET;
+ } else if (hwrev == IGEP2_BOARD_HWREV_C || machine_is_igep0030()) {
+ igep_wlan_bt_gpios[0].gpio = IGEP2_RC_GPIO_WIFI_NPD;
+ igep_wlan_bt_gpios[1].gpio = IGEP2_RC_GPIO_WIFI_NRESET;
+ igep_wlan_bt_gpios[2].gpio = IGEP2_RC_GPIO_BT_NRESET;
} else
return;
- /* Set GPIO's for WLAN-BT combo module */
- if ((gpio_request(npd, "GPIO_WIFI_NPD") == 0) &&
- (gpio_direction_output(npd, 1) == 0)) {
- gpio_export(npd, 0);
- } else
- pr_warning("IGEP2: Could not obtain gpio GPIO_WIFI_NPD\n");
-
- if ((gpio_request(wreset, "GPIO_WIFI_NRESET") == 0) &&
- (gpio_direction_output(wreset, 1) == 0)) {
- gpio_export(wreset, 0);
- gpio_set_value(wreset, 0);
- udelay(10);
- gpio_set_value(wreset, 1);
- } else
- pr_warning("IGEP2: Could not obtain gpio GPIO_WIFI_NRESET\n");
+ err = gpio_request_array(igep_wlan_bt_gpios,
+ ARRAY_SIZE(igep_wlan_bt_gpios));
+ if (err) {
+ pr_warning("IGEP2: Could not obtain WIFI/BT gpios\n");
+ return;
+ }
+
+ gpio_export(igep_wlan_bt_gpios[0].gpio, 0);
+ gpio_export(igep_wlan_bt_gpios[1].gpio, 0);
+ gpio_export(igep_wlan_bt_gpios[2].gpio, 0);
+
+ gpio_set_value(igep_wlan_bt_gpios[1].gpio, 0);
+ udelay(10);
+ gpio_set_value(igep_wlan_bt_gpios[1].gpio, 1);
- if ((gpio_request(btreset, "GPIO_BT_NRESET") == 0) &&
- (gpio_direction_output(btreset, 1) == 0)) {
- gpio_export(btreset, 0);
- } else
- pr_warning("IGEP2: Could not obtain gpio GPIO_BT_NRESET\n");
}
#else
-static inline void __init igep2_wlan_bt_init(void) { }
+static inline void __init igep_wlan_bt_init(void) { }
#endif
-static void __init igep2_init(void)
+static void __init igep_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
/* Get IGEP2 hardware revision */
igep2_get_revision();
/* Register I2C busses and drivers */
- igep2_i2c_init();
- platform_add_devices(igep2_devices, ARRAY_SIZE(igep2_devices));
- omap_display_init(&igep2_dss_data);
+ igep_i2c_init();
+ platform_add_devices(igep_devices, ARRAY_SIZE(igep_devices));
omap_serial_init();
- usb_musb_init(&musb_board_data);
- usbhs_init(&usbhs_bdata);
+ usb_musb_init(NULL);
- igep2_flash_init();
- igep2_leds_init();
- igep2_display_init();
- igep2_init_smsc911x();
+ igep_flash_init();
+ igep_leds_init();
/*
* WLAN-BT combo module from MuRata which has a Marvell WLAN
* (88W8686) + CSR Bluetooth chipset. Uses SDIO interface.
*/
- igep2_wlan_bt_init();
+ igep_wlan_bt_init();
+ if (machine_is_igep0020()) {
+ omap_display_init(&igep2_dss_data);
+ igep2_display_init();
+ igep2_init_smsc911x();
+ usbhs_init(&igep2_usbhs_bdata);
+ } else {
+ usbhs_init(&igep3_usbhs_bdata);
+ }
}
MACHINE_START(IGEP0020, "IGEP v2 board")
.boot_params = 0x80000100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
- .init_early = igep2_init_early,
- .init_irq = omap_init_irq,
- .init_machine = igep2_init,
- .timer = &omap_timer,
+ .init_early = igep_init_early,
+ .init_irq = omap3_init_irq,
+ .init_machine = igep_init,
+ .timer = &omap3_timer,
+MACHINE_END
+
+MACHINE_START(IGEP0030, "IGEP OMAP3 module")
+ .boot_params = 0x80000100,
+ .reserve = omap_reserve,
+ .map_io = omap3_map_io,
+ .init_early = igep_init_early,
+ .init_irq = omap3_init_irq,
+ .init_machine = igep_init,
+ .timer = &omap3_timer,
MACHINE_END
git.openpandora.org / pandora-kernel.git / blobdiff