+
+/* --------------------------------------------------------------------
+ * NAND / SmartMedia
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
+static struct at91_nand_data nand_data;
+
+static struct resource at91_nand_resources[] = {
+ {
+ .start = AT91_SMARTMEDIA_BASE,
+ .end = AT91_SMARTMEDIA_BASE + SZ_8M - 1,
+ .flags = IORESOURCE_MEM,
+ }
+};
+
+static struct platform_device at91_nand_device = {
+ .name = "at91_nand",
+ .id = -1,
+ .dev = {
+ .platform_data = &nand_data,
+ },
+ .resource = at91_nand_resources,
+ .num_resources = ARRAY_SIZE(at91_nand_resources),
+};
+
+void __init at91_add_device_nand(struct at91_nand_data *data)
+{
+ if (!data)
+ return;
+
+ /* enable pin */
+ if (data->enable_pin)
+ at91_set_gpio_output(data->enable_pin, 1);
+
+ /* ready/busy pin */
+ if (data->rdy_pin)
+ at91_set_gpio_input(data->rdy_pin, 1);
+
+ /* card detect pin */
+ if (data->det_pin)
+ at91_set_gpio_input(data->det_pin, 1);
+
+ at91_set_A_periph(AT91_PIN_PC1, 0); /* SMOE */
+ at91_set_A_periph(AT91_PIN_PC3, 0); /* SMWE */
+
+ nand_data = *data;
+ platform_device_register(&at91_nand_device);
+}
+#else
+void __init at91_add_device_nand(struct at91_nand_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ * TWI (i2c)
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
+static struct platform_device at91rm9200_twi_device = {
+ .name = "at91_i2c",
+ .id = -1,
+ .num_resources = 0,
+};
+
+void __init at91_add_device_i2c(void)
+{
+ /* pins used for TWI interface */
+ at91_set_A_periph(AT91_PIN_PA25, 0); /* TWD */
+ at91_set_multi_drive(AT91_PIN_PA25, 1);
+
+ at91_set_A_periph(AT91_PIN_PA26, 0); /* TWCK */
+ at91_set_multi_drive(AT91_PIN_PA26, 1);
+
+ platform_device_register(&at91rm9200_twi_device);
+}
+#else
+void __init at91_add_device_i2c(void) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ * SPI
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SPI_AT91) || defined(CONFIG_SPI_AT91_MODULE) || defined(CONFIG_AT91_SPI) || defined(CONFIG_AT91_SPI_MODULE)
+static u64 spi_dmamask = 0xffffffffUL;
+
+static struct resource at91_spi_resources[] = {
+ [0] = {
+ .start = AT91_BASE_SPI,
+ .end = AT91_BASE_SPI + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91_ID_SPI,
+ .end = AT91_ID_SPI,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91rm9200_spi_device = {
+ .name = "at91_spi",
+ .id = 0,
+ .dev = {
+ .dma_mask = &spi_dmamask,
+ .coherent_dma_mask = 0xffffffff,
+ },
+ .resource = at91_spi_resources,
+ .num_resources = ARRAY_SIZE(at91_spi_resources),
+};
+
+static const unsigned at91_spi_standard_cs[4] = { AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PA5, AT91_PIN_PA6 };
+
+void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
+{
+ int i;
+ unsigned long cs_pin;
+
+ at91_set_A_periph(AT91_PIN_PA0, 0); /* MISO */
+ at91_set_A_periph(AT91_PIN_PA1, 0); /* MOSI */
+ at91_set_A_periph(AT91_PIN_PA2, 0); /* SPCK */
+
+ /* Enable SPI chip-selects */
+ for (i = 0; i < nr_devices; i++) {
+ if (devices[i].controller_data)
+ cs_pin = (unsigned long) devices[i].controller_data;
+ else
+ cs_pin = at91_spi_standard_cs[devices[i].chip_select];
+
+#ifdef CONFIG_SPI_AT91_MANUAL_CS
+ at91_set_gpio_output(cs_pin, 1);
+#else
+ at91_set_A_periph(cs_pin, 0);
+#endif
+
+ /* pass chip-select pin to driver */
+ devices[i].controller_data = (void *) cs_pin;
+ }
+
+ spi_register_board_info(devices, nr_devices);
+ at91_clock_associate("spi0_clk", &at91rm9200_spi_device.dev, "spi");
+ platform_device_register(&at91rm9200_spi_device);
+}
+#else
+void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ * RTC
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_RTC_DRV_AT91) || defined(CONFIG_RTC_DRV_AT91_MODULE)
+static struct platform_device at91rm9200_rtc_device = {
+ .name = "at91_rtc",
+ .id = -1,
+ .num_resources = 0,
+};
+
+static void __init at91_add_device_rtc(void)
+{
+ platform_device_register(&at91rm9200_rtc_device);
+}
+#else
+static void __init at91_add_device_rtc(void) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ * Watchdog
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_AT91_WATCHDOG) || defined(CONFIG_AT91_WATCHDOG_MODULE)
+static struct platform_device at91rm9200_wdt_device = {
+ .name = "at91_wdt",
+ .id = -1,
+ .num_resources = 0,
+};
+
+static void __init at91_add_device_watchdog(void)
+{
+ platform_device_register(&at91rm9200_wdt_device);
+}
+#else
+static void __init at91_add_device_watchdog(void) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ * LEDs
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_LEDS)
+u8 at91_leds_cpu;
+u8 at91_leds_timer;
+
+void __init at91_init_leds(u8 cpu_led, u8 timer_led)
+{
+ at91_leds_cpu = cpu_led;
+ at91_leds_timer = timer_led;
+}
+#else
+void __init at91_init_leds(u8 cpu_led, u8 timer_led) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ * UART
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SERIAL_AT91)
+static struct resource dbgu_resources[] = {
+ [0] = {
+ .start = AT91_VA_BASE_SYS + AT91_DBGU,
+ .end = AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91_ID_SYS,
+ .end = AT91_ID_SYS,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct at91_uart_data dbgu_data = {
+ .use_dma_tx = 0,
+ .use_dma_rx = 0, /* DBGU not capable of receive DMA */
+};
+
+static struct platform_device at91rm9200_dbgu_device = {
+ .name = "at91_usart",
+ .id = 0,
+ .dev = {
+ .platform_data = &dbgu_data,
+ .coherent_dma_mask = 0xffffffff,
+ },
+ .resource = dbgu_resources,
+ .num_resources = ARRAY_SIZE(dbgu_resources),
+};
+
+static inline void configure_dbgu_pins(void)
+{
+ at91_set_A_periph(AT91_PIN_PA30, 0); /* DRXD */
+ at91_set_A_periph(AT91_PIN_PA31, 1); /* DTXD */
+}
+
+static struct resource uart0_resources[] = {
+ [0] = {
+ .start = AT91_BASE_US0,
+ .end = AT91_BASE_US0 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91_ID_US0,
+ .end = AT91_ID_US0,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct at91_uart_data uart0_data = {
+ .use_dma_tx = 1,
+ .use_dma_rx = 1,
+};
+
+static struct platform_device at91rm9200_uart0_device = {
+ .name = "at91_usart",
+ .id = 1,
+ .dev = {
+ .platform_data = &uart0_data,
+ .coherent_dma_mask = 0xffffffff,
+ },
+ .resource = uart0_resources,
+ .num_resources = ARRAY_SIZE(uart0_resources),
+};
+
+static inline void configure_usart0_pins(void)
+{
+ at91_set_A_periph(AT91_PIN_PA17, 1); /* TXD0 */
+ at91_set_A_periph(AT91_PIN_PA18, 0); /* RXD0 */
+ at91_set_A_periph(AT91_PIN_PA20, 0); /* CTS0 */
+
+ /*
+ * AT91RM9200 Errata #39 - RTS0 is not internally connected to PA21.
+ * We need to drive the pin manually. Default is off (RTS is active low).
+ */
+ at91_set_gpio_output(AT91_PIN_PA21, 1);
+}
+
+static struct resource uart1_resources[] = {
+ [0] = {
+ .start = AT91_BASE_US1,
+ .end = AT91_BASE_US1 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91_ID_US1,
+ .end = AT91_ID_US1,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct at91_uart_data uart1_data = {
+ .use_dma_tx = 1,
+ .use_dma_rx = 1,
+};
+
+static struct platform_device at91rm9200_uart1_device = {
+ .name = "at91_usart",
+ .id = 2,
+ .dev = {
+ .platform_data = &uart1_data,
+ .coherent_dma_mask = 0xffffffff,
+ },
+ .resource = uart1_resources,
+ .num_resources = ARRAY_SIZE(uart1_resources),
+};
+
+static inline void configure_usart1_pins(void)
+{
+ at91_set_A_periph(AT91_PIN_PB18, 0); /* RI1 */
+ at91_set_A_periph(AT91_PIN_PB19, 0); /* DTR1 */
+ at91_set_A_periph(AT91_PIN_PB20, 1); /* TXD1 */
+ at91_set_A_periph(AT91_PIN_PB21, 0); /* RXD1 */
+ at91_set_A_periph(AT91_PIN_PB23, 0); /* DCD1 */
+ at91_set_A_periph(AT91_PIN_PB24, 0); /* CTS1 */
+ at91_set_A_periph(AT91_PIN_PB25, 0); /* DSR1 */
+ at91_set_A_periph(AT91_PIN_PB26, 0); /* RTS1 */
+}
+
+static struct resource uart2_resources[] = {
+ [0] = {
+ .start = AT91_BASE_US2,
+ .end = AT91_BASE_US2 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91_ID_US2,
+ .end = AT91_ID_US2,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct at91_uart_data uart2_data = {
+ .use_dma_tx = 1,
+ .use_dma_rx = 1,
+};
+
+static struct platform_device at91rm9200_uart2_device = {
+ .name = "at91_usart",
+ .id = 3,
+ .dev = {
+ .platform_data = &uart2_data,
+ .coherent_dma_mask = 0xffffffff,
+ },
+ .resource = uart2_resources,
+ .num_resources = ARRAY_SIZE(uart2_resources),
+};
+
+static inline void configure_usart2_pins(void)
+{
+ at91_set_A_periph(AT91_PIN_PA22, 0); /* RXD2 */
+ at91_set_A_periph(AT91_PIN_PA23, 1); /* TXD2 */
+}
+
+static struct resource uart3_resources[] = {
+ [0] = {
+ .start = AT91_BASE_US3,
+ .end = AT91_BASE_US3 + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91_ID_US3,
+ .end = AT91_ID_US3,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct at91_uart_data uart3_data = {
+ .use_dma_tx = 1,
+ .use_dma_rx = 1,
+};
+
+static struct platform_device at91rm9200_uart3_device = {
+ .name = "at91_usart",
+ .id = 4,
+ .dev = {
+ .platform_data = &uart3_data,
+ .coherent_dma_mask = 0xffffffff,
+ },
+ .resource = uart3_resources,
+ .num_resources = ARRAY_SIZE(uart3_resources),
+};
+
+static inline void configure_usart3_pins(void)
+{
+ at91_set_B_periph(AT91_PIN_PA5, 1); /* TXD3 */
+ at91_set_B_periph(AT91_PIN_PA6, 0); /* RXD3 */
+}
+
+struct platform_device *at91_uarts[AT91_NR_UART]; /* the UARTs to use */
+struct platform_device *at91_default_console_device; /* the serial console device */
+
+void __init at91_init_serial(struct at91_uart_config *config)
+{
+ int i;
+
+ /* Fill in list of supported UARTs */
+ for (i = 0; i < config->nr_tty; i++) {
+ switch (config->tty_map[i]) {
+ case 0:
+ configure_usart0_pins();
+ at91_uarts[i] = &at91rm9200_uart0_device;
+ at91_clock_associate("usart0_clk", &at91rm9200_uart0_device.dev, "usart");
+ break;
+ case 1:
+ configure_usart1_pins();
+ at91_uarts[i] = &at91rm9200_uart1_device;
+ at91_clock_associate("usart1_clk", &at91rm9200_uart1_device.dev, "usart");
+ break;
+ case 2:
+ configure_usart2_pins();
+ at91_uarts[i] = &at91rm9200_uart2_device;
+ at91_clock_associate("usart2_clk", &at91rm9200_uart2_device.dev, "usart");
+ break;
+ case 3:
+ configure_usart3_pins();
+ at91_uarts[i] = &at91rm9200_uart3_device;
+ at91_clock_associate("usart3_clk", &at91rm9200_uart3_device.dev, "usart");
+ break;
+ case 4:
+ configure_dbgu_pins();
+ at91_uarts[i] = &at91rm9200_dbgu_device;
+ at91_clock_associate("mck", &at91rm9200_dbgu_device.dev, "usart");
+ break;
+ default:
+ continue;
+ }
+ at91_uarts[i]->id = i; /* update ID number to mapped ID */
+ }
+
+ /* Set serial console device */
+ if (config->console_tty < AT91_NR_UART)
+ at91_default_console_device = at91_uarts[config->console_tty];
+ if (!at91_default_console_device)
+ printk(KERN_INFO "AT91: No default serial console defined.\n");
+}
+
+void __init at91_add_device_serial(void)
+{
+ int i;
+
+ for (i = 0; i < AT91_NR_UART; i++) {
+ if (at91_uarts[i])
+ platform_device_register(at91_uarts[i]);
+ }
+}
+#else
+void __init at91_init_serial(struct at91_uart_config *config) {}
+void __init at91_add_device_serial(void) {}
+#endif
+
+