slots - Reserve the slot index for the given driver.
This option takes multiple strings.
See "Module Autoloading Support" section for details.
+ debug - Specifies the debug message level
+ (0 = disable debug prints, 1 = normal debug messages,
+ 2 = verbose debug messages)
+ This option appears only when CONFIG_SND_DEBUG=y.
+ This option can be dynamically changed via sysfs
+ /sys/modules/snd/parameters/debug file.
Module snd-pcm-oss
------------------
The power-management is supported.
+ Module snd-ctxfi
+ ----------------
+
+ Module for Creative Sound Blaster X-Fi boards (20k1 / 20k2 chips)
+ * Creative Sound Blaster X-Fi Titanium Fatal1ty Champion Series
+ * Creative Sound Blaster X-Fi Titanium Fatal1ty Professional Series
+ * Creative Sound Blaster X-Fi Titanium Professional Audio
+ * Creative Sound Blaster X-Fi Titanium
+ * Creative Sound Blaster X-Fi Elite Pro
+ * Creative Sound Blaster X-Fi Platinum
+ * Creative Sound Blaster X-Fi Fatal1ty
+ * Creative Sound Blaster X-Fi XtremeGamer
+ * Creative Sound Blaster X-Fi XtremeMusic
+
+ reference_rate - reference sample rate, 44100 or 48000 (default)
+ multiple - multiple to ref. sample rate, 1 or 2 (default)
+
+ This module supports multiple cards.
+
Module snd-darla20
------------------
or input, but you may use this module for any application which
requires a sound card (like RealPlayer).
+ pcm_devs - Number of PCM devices assigned to each card
+ (default = 1, up to 4)
+ pcm_substreams - Number of PCM substreams assigned to each PCM
+ (default = 8, up to 16)
+ hrtimer - Use hrtimer (=1, default) or system timer (=0)
+ fake_buffer - Fake buffer allocations (default = 1)
+
+ When multiple PCM devices are created, snd-dummy gives different
+ behavior to each PCM device:
+ 0 = interleaved with mmap support
+ 1 = non-interleaved with mmap support
+ 2 = interleaved without mmap
+ 3 = non-interleaved without mmap
+
+ As default, snd-dummy drivers doesn't allocate the real buffers
+ but either ignores read/write or mmap a single dummy page to all
+ buffer pages, in order to save the resouces. If your apps need
+ the read/ written buffer data to be consistent, pass fake_buffer=0
+ option.
+
The power-management is supported.
Module snd-echo3g
single_cmd - Use single immediate commands to communicate with
codecs (for debugging only)
enable_msi - Enable Message Signaled Interrupt (MSI) (default = off)
- power_save - Automatic power-saving timtout (in second, 0 =
+ power_save - Automatic power-saving timeout (in second, 0 =
disable)
power_save_controller - Reset HD-audio controller in power-saving mode
(default = on)
* Onkyo SE-90PCI
* Onkyo SE-200PCI
* ESI Juli@
+ * ESI Maya44
* Hercules Fortissimo IV
* EGO-SYS WaveTerminal 192M
prodigy71xt, prodigy71hifi, prodigyhd2, prodigy192,
juli, aureon51, aureon71, universe, ap192, k8x800,
phase22, phase28, ms300, av710, se200pci, se90pci,
- fortissimo4, sn25p, WT192M
+ fortissimo4, sn25p, WT192M, maya44
This module supports multiple cards and autoprobe.
This module supports multiple cards.
The driver requires the firmware loader support on kernel.
+ Module snd-lx6464es
+ -------------------
+
+ Module for Digigram LX6464ES boards
+
+ This module supports multiple cards.
+
Module snd-maestro3
-------------------
Module snd-sc6000
-----------------
- Module for Gallant SC-6000 soundcard.
+ Module for Gallant SC-6000 soundcard and later models: SC-6600
+ and SC-7000.
port - Port # (0x220 or 0x240)
mss_port - MSS Port # (0x530 or 0xe80)
irq - IRQ # (5,7,9,10,11)
mpu_irq - MPU-401 IRQ # (5,7,9,10) ,0 - no MPU-401 irq
dma - DMA # (1,3,0)
+ joystick - Enable gameport - 0 = disable (default), 1 = enable
This module supports multiple cards.
-------------------
Module for sound cards based on the Asus AV100/AV200 chips,
- i.e., Xonar D1, DX, D2, D2X, HDAV1.3 (Deluxe), and Essence STX.
+ i.e., Xonar D1, DX, D2, D2X, HDAV1.3 (Deluxe), Essence ST
+ (Deluxe) and Essence STX.
This module supports autoprobe and multiple cards.