enable - enable card
- Default: enabled, for PCI and ISA PnP cards
+ Module snd-adlib
+ ----------------
+
+ Module for AdLib FM cards.
+
+ port - port # for OPL chip
+
+ This module supports multiple cards. It does not support autoprobe, so
+ the port must be specified. For actual AdLib FM cards it will be 0x388.
+ Note that this card does not have PCM support and no mixer; only FM
+ synthesis.
+
+ Make sure you have "sbiload" from the alsa-tools package available and,
+ after loading the module, find out the assigned ALSA sequencer port
+ number through "sbiload -l". Example output:
+
+ Port Client name Port name
+ 64:0 OPL2 FM synth OPL2 FM Port
+
+ Load the std.sb and drums.sb patches also supplied by sbiload:
+
+ sbiload -p 64:0 std.sb drums.sb
+
+ If you use this driver to drive an OPL3, you can use std.o3 and drums.o3
+ instead. To have the card produce sound, use aplaymidi from alsa-utils:
+
+ aplaymidi -p 64:0 foo.mid
+
Module snd-ad1816a
------------------
The power-management is supported.
+ Module snd-als300
+ -----------------
+
+ Module for Avance Logic ALS300 and ALS300+
+
+ This module supports multiple cards.
+
+ The power-management is supported.
+
Module snd-als4000
------------------
This module supports multiple cards and autoprobe.
+ The power-management is supported.
+
Module snd-ens1371
------------------
This module supports multiple cards and autoprobe.
+ The power-management is supported.
+
Module snd-es968
----------------
model - force the model name
position_fix - Fix DMA pointer (0 = auto, 1 = none, 2 = POSBUF, 3 = FIFO size)
+ single_cmd - Use single immediate commands to communicate with
+ codecs (for debugging only)
This module supports one card and autoprobe.
asus 3-jack
uniwill 3-jack
F1734 2-jack
+ lg LG laptop (m1 express dual)
+ lg-lw LG LW20 laptop
test for testing/debugging purpose, almost all controls can be
adjusted. Appearing only when compiled with
$CONFIG_SND_DEBUG=y
+ auto auto-config reading BIOS (default)
ALC260
hp HP machines
fujitsu Fujitsu S7020
+ acer Acer TravelMate
+ basic fixed pin assignment (old default model)
+ auto auto-config reading BIOS (default)
+
+ ALC262
+ fujitsu Fujitsu Laptop
+ basic fixed pin assignment w/o SPDIF
+ auto auto-config reading BIOS (default)
+
+ ALC882/883/885
+ 3stack-dig 3-jack with SPDIF I/O
+ 6stck-dig 6-jack digital with SPDIF I/O
+ auto auto-config reading BIOS (default)
+
+ ALC861
+ 3stack 3-jack
+ 3stack-dig 3-jack with SPDIF I/O
+ 6stack-dig 6-jack with SPDIF I/O
+ auto auto-config reading BIOS (default)
CMI9880
minimal 3-jack in back
allout 5-jack in back, 2-jack in front, SPDIF out
auto auto-config reading BIOS (default)
+ AD1981
+ basic 3-jack (default)
+ hp HP nx6320
+
+ AD1986A
+ 6stack 6-jack, separate surrounds (default)
+ 3stack 3-stack, shared surrounds
+ laptop 2-channel only (FSC V2060, Samsung M50)
+ laptop-eapd 2-channel with EAPD (Samsung R65, ASUS A6J)
+
+ AD1988
+ 6stack 6-jack
+ 6stack-dig ditto with SPDIF
+ 3stack 3-jack
+ 3stack-dig ditto with SPDIF
+ laptop 3-jack with hp-jack automute
+ laptop-dig ditto with SPDIF
+ auto auto-confgi reading BIOS (default)
+
+ STAC7661(?)
+ vaio Setup for VAIO FE550G/SZ110
+
If the default configuration doesn't work and one of the above
matches with your device, report it together with the PCI
subsystem ID (output of "lspci -nv") to ALSA BTS or alsa-devel
(Usually SD_LPLIB register is more accurate than the
position buffer.)
+ NB: If you get many "azx_get_response timeout" messages at
+ loading, it's likely a problem of interrupts (e.g. ACPI irq
+ routing). Try to boot with options like "pci=noacpi". Also, you
+ can try "single_cmd=1" module option. This will switch the
+ communication method between HDA controller and codecs to the
+ single immediate commands instead of CORB/RIRB. Basically, the
+ single command mode is provided only for BIOS, and you won't get
+ unsolicited events, too. But, at least, this works independently
+ from the irq. Remember this is a last resort, and should be
+ avoided as much as possible...
+
The power-management is supported.
Module snd-hdsp
------------------
Module for Envy24HT (VT/ICE1724), Envy24PT (VT1720) based PCI sound cards.
+ * MidiMan M Audio Revolution 5.1
* MidiMan M Audio Revolution 7.1
* AMP Ltd AUDIO2000
* TerraTec Aureon 5.1 Sky
* TerraTec Phase 22
* TerraTec Phase 28
* AudioTrak Prodigy 7.1
+ * AudioTrak Prodigy 7.1LT
* AudioTrak Prodigy 192
* Pontis MS300
* Albatron K8X800 Pro II
* Shuttle SN25P
model - Use the given board model, one of the following:
- revo71, amp2000, prodigy71, prodigy192, aureon51,
- aureon71, universe, k8x800, phase22, phase28, ms300,
- av710
+ revo51, revo71, amp2000, prodigy71, prodigy71lt,
+ prodigy192, aureon51, aureon71, universe,
+ k8x800, phase22, phase28, ms300, av710
This module supports multiple cards and autoprobe.
The power-management is supported.
+ Module snd-miro
+ ---------------
+
+ Module for Miro soundcards: miroSOUND PCM 1 pro,
+ miroSOUND PCM 12,
+ miroSOUND PCM 20 Radio.
+
+ port - Port # (0x530,0x604,0xe80,0xf40)
+ irq - IRQ # (5,7,9,10,11)
+ dma1 - 1st dma # (0,1,3)
+ dma2 - 2nd dma # (0,1)
+ mpu_port - MPU-401 port # (0x300,0x310,0x320,0x330)
+ mpu_irq - MPU-401 irq # (5,7,9,10)
+ fm_port - FM Port # (0x388)
+ wss - enable WSS mode
+ ide - enable onboard ide support
+
Module snd-mixart
-----------------
The power-management is supported.
+ Module snd-riptide
+ ------------------
+
+ Module for Conexant Riptide chip
+
+ joystick_port - Joystick port # (default: 0x200)
+ mpu_port - MPU401 port # (default: 0x330)
+ opl3_port - OPL3 port # (default: 0x388)
+
+ This module supports multiple cards.
+ The driver requires the firmware loader support on kernel.
+ You need to install the firmware file "riptide.hex" to the standard
+ firmware path (e.g. /lib/firmware).
+
Module snd-rme32
----------------
vid - Vendor ID for the device (optional)
pid - Product ID for the device (optional)
+ device_setup - Device specific magic number (optional)
+ - Influence depends on the device
+ - Default: 0x0000
This module supports multiple devices, autoprobe and hotplugging.
git.openpandora.org / pandora-kernel.git / blobdiff