VI - System-on-a-chip devices and nodes
1) Defining child nodes of an SOC
2) Representing devices without a current OF specification
- a) PHY nodes
- b) Interrupt controllers
- c) CFI or JEDEC memory-mapped NOR flash
- d) 4xx/Axon EMAC ethernet nodes
- e) Xilinx IP cores
- f) USB EHCI controllers
+ a) MDIO IO device
+ b) Gianfar-compatible ethernet nodes
+ c) PHY nodes
+ d) Interrupt controllers
+ e) I2C
+ f) Freescale SOC USB controllers
+ g) Freescale SOC SEC Security Engines
+ h) Board Control and Status (BCSR)
+ i) Freescale QUICC Engine module (QE)
+ j) CFI or JEDEC memory-mapped NOR flash
+ k) Global Utilities Block
+ l) Freescale Communications Processor Module
+ m) Chipselect/Local Bus
+ n) 4xx/Axon EMAC ethernet nodes
+ o) Xilinx IP cores
+ p) Freescale Synchronous Serial Interface
+ q) USB EHCI controllers
+ r) MDIO on GPIOs
+ s) SPI busses
VII - Marvell Discovery mv64[345]6x System Controller chips
1) The /system-controller node
big-endian;
};
+ r) Freescale Display Interface Unit
+
+ The Freescale DIU is a LCD controller, with proper hardware, it can also
+ drive DVI monitors.
+
+ Required properties:
+ - compatible : should be "fsl-diu".
+ - reg : should contain at least address and length of the DIU register
+ set.
+ - Interrupts : one DIU interrupt should be describe here.
+
+ Example (MPC8610HPCD)
+ display@2c000 {
+ compatible = "fsl,diu";
+ reg = <0x2c000 100>;
+ interrupts = <72 2>;
+ interrupt-parent = <&mpic>;
+ };
+
+ s) Freescale on board FPGA
+
+ This is the memory-mapped registers for on board FPGA.
+
+ Required properities:
+ - compatible : should be "fsl,fpga-pixis".
+ - reg : should contain the address and the lenght of the FPPGA register
+ set.
+
+ Example (MPC8610HPCD)
+ board-control@e8000000 {
+ compatible = "fsl,fpga-pixis";
+ reg = <0xe8000000 32>;
+ };
+
+ r) MDIO on GPIOs
+
+ Currently defined compatibles:
+ - virtual,gpio-mdio
+
+ MDC and MDIO lines connected to GPIO controllers are listed in the
+ gpios property as described in section VIII.1 in the following order:
+
+ MDC, MDIO.
+
+ Example:
+
+ mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&qe_pio_a 11
+ &qe_pio_c 6>;
+ };
+
+ s) SPI (Serial Peripheral Interface) busses
+
+ SPI busses can be described with a node for the SPI master device
+ and a set of child nodes for each SPI slave on the bus. For this
+ discussion, it is assumed that the system's SPI controller is in
+ SPI master mode. This binding does not describe SPI controllers
+ in slave mode.
+
+ The SPI master node requires the following properties:
+ - #address-cells - number of cells required to define a chip select
+ address on the SPI bus.
+ - #size-cells - should be zero.
+ - compatible - name of SPI bus controller following generic names
+ recommended practice.
+ No other properties are required in the SPI bus node. It is assumed
+ that a driver for an SPI bus device will understand that it is an SPI bus.
+ However, the binding does not attempt to define the specific method for
+ assigning chip select numbers. Since SPI chip select configuration is
+ flexible and non-standardized, it is left out of this binding with the
+ assumption that board specific platform code will be used to manage
+ chip selects. Individual drivers can define additional properties to
+ support describing the chip select layout.
+
+ SPI slave nodes must be children of the SPI master node and can
+ contain the following properties.
+ - reg - (required) chip select address of device.
+ - compatible - (required) name of SPI device following generic names
+ recommended practice
+ - spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz
+ - spi-cpol - (optional) Empty property indicating device requires
+ inverse clock polarity (CPOL) mode
+ - spi-cpha - (optional) Empty property indicating device requires
+ shifted clock phase (CPHA) mode
+
+ SPI example for an MPC5200 SPI bus:
+ spi@f00 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
+ reg = <0xf00 0x20>;
+ interrupts = <2 13 0 2 14 0>;
+ interrupt-parent = <&mpc5200_pic>;
+
+ ethernet-switch@0 {
+ compatible = "micrel,ks8995m";
+ spi-max-frequency = <1000000>;
+ reg = <0>;
+ };
+
+ codec@1 {
+ compatible = "ti,tlv320aic26";
+ spi-max-frequency = <100000>;
+ reg = <1>;
+ };
+ };
+
VII - Marvell Discovery mv64[345]6x System Controller chips
===========================================================
git.openpandora.org / pandora-kernel.git / blobdiff