-* OpenPIC and its interrupt numbers on Freescale's e500/e600 cores
-
-The OpenPIC specification does not specify which interrupt source has to
-become which interrupt number. This is up to the software implementation
-of the interrupt controller. The only requirement is that every
-interrupt source has to have an unique interrupt number / vector number.
-To accomplish this the current implementation assigns the number zero to
-the first source, the number one to the second source and so on until
-all interrupt sources have their unique number.
-Usually the assigned vector number equals the interrupt number mentioned
-in the documentation for a given core / CPU. This is however not true
-for the e500 cores (MPC85XX CPUs) where the documentation distinguishes
-between internal and external interrupt sources and starts counting at
-zero for both of them.
-
-So what to write for external interrupt source X or internal interrupt
-source Y into the device tree? Here is an example:
-
-The memory map for the interrupt controller in the MPC8544[0] shows,
-that the first interrupt source starts at 0x5_0000 (PIC Register Address
-Map-Interrupt Source Configuration Registers). This source becomes the
-number zero therefore:
- External interrupt 0 = interrupt number 0
- External interrupt 1 = interrupt number 1
- External interrupt 2 = interrupt number 2
- ...
-Every interrupt number allocates 0x20 bytes register space. So to get
-its number it is sufficient to shift the lower 16bits to right by five.
-So for the external interrupt 10 we have:
- 0x0140 >> 5 = 10
-
-After the external sources, the internal sources follow. The in core I2C
-controller on the MPC8544 for instance has the internal source number
-27. Oo obtain its interrupt number we take the lower 16bits of its memory
-address (0x5_0560) and shift it right:
- 0x0560 >> 5 = 43
-
-Therefore the I2C device node for the MPC8544 CPU has to have the
-interrupt number 43 specified in the device tree.
-
-[0] MPC8544E PowerQUICCTM III, Integrated Host Processor Family Reference Manual
- MPC8544ERM Rev. 1 10/2007
+=====================================================================
+Freescale MPIC Interrupt Controller Node
+Copyright (C) 2010,2011 Freescale Semiconductor Inc.
+=====================================================================
+
+The Freescale MPIC interrupt controller is found on all PowerQUICC
+and QorIQ processors and is compatible with the Open PIC. The
+notable difference from Open PIC binding is the addition of 2
+additional cells in the interrupt specifier defining interrupt type
+information.
+
+PROPERTIES
+
+ - compatible
+ Usage: required
+ Value type: <string>
+ Definition: Shall include "fsl,mpic". Freescale MPIC
+ controllers compatible with this binding have Block
+ Revision Registers BRR1 and BRR2 at offset 0x0 and
+ 0x10 in the MPIC.
+
+ - reg
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: A standard property. Specifies the physical
+ offset and length of the device's registers within the
+ CCSR address space.
+
+ - interrupt-controller
+ Usage: required
+ Value type: <empty>
+ Definition: Specifies that this node is an interrupt
+ controller
+
+ - #interrupt-cells
+ Usage: required
+ Value type: <u32>
+ Definition: Shall be 2 or 4. A value of 2 means that interrupt
+ specifiers do not contain the interrupt-type or type-specific
+ information cells.
+
+ - #address-cells
+ Usage: required
+ Value type: <u32>
+ Definition: Shall be 0.
+
+ - pic-no-reset
+ Usage: optional
+ Value type: <empty>
+ Definition: The presence of this property specifies that the
+ MPIC must not be reset by the client program, and that
+ the boot program has initialized all interrupt source
+ configuration registers to a sane state-- masked or
+ directed at other cores. This ensures that the client
+ program will not receive interrupts for sources not belonging
+ to the client. The presence of this property also mandates
+ that any initialization related to interrupt sources shall
+ be limited to sources explicitly referenced in the device tree.
+
+INTERRUPT SPECIFIER DEFINITION
+
+ Interrupt specifiers consists of 4 cells encoded as
+ follows:
+
+ <1st-cell> interrupt-number
+
+ Identifies the interrupt source. The meaning
+ depends on the type of interrupt.
+
+ Note: If the interrupt-type cell is undefined
+ (i.e. #interrupt-cells = 2), this cell
+ should be interpreted the same as for
+ interrupt-type 0-- i.e. an external or
+ normal SoC device interrupt.
+
+ <2nd-cell> level-sense information, encoded as follows:
+ 0 = low-to-high edge triggered
+ 1 = active low level-sensitive
+ 2 = active high level-sensitive
+ 3 = high-to-low edge triggered
+
+ <3rd-cell> interrupt-type
+
+ The following types are supported:
+
+ 0 = external or normal SoC device interrupt
+
+ The interrupt-number cell contains
+ the SoC device interrupt number. The
+ type-specific cell is undefined. The
+ interrupt-number is derived from the
+ MPIC a block of registers referred to as
+ the "Interrupt Source Configuration Registers".
+ Each source has 32-bytes of registers
+ (vector/priority and destination) in this
+ region. So interrupt 0 is at offset 0x0,
+ interrupt 1 is at offset 0x20, and so on.
+
+ 1 = error interrupt
+
+ The interrupt-number cell contains
+ the SoC device interrupt number for
+ the error interrupt. The type-specific
+ cell identifies the specific error
+ interrupt number.
+
+ 2 = MPIC inter-processor interrupt (IPI)
+
+ The interrupt-number cell identifies
+ the MPIC IPI number. The type-specific
+ cell is undefined.
+
+ 3 = MPIC timer interrupt
+
+ The interrupt-number cell identifies
+ the MPIC timer number. The type-specific
+ cell is undefined.
+
+ <4th-cell> type-specific information
+
+ The type-specific cell is encoded as follows:
+
+ - For interrupt-type 1 (error interrupt),
+ the type-specific cell contains the
+ bit number of the error interrupt in the
+ Error Interrupt Summary Register.
+
+EXAMPLE 1
+ /*
+ * mpic interrupt controller with 4 cells per specifier
+ */
+ mpic: pic@40000 {
+ compatible = "fsl,mpic";
+ interrupt-controller;
+ #interrupt-cells = <4>;
+ #address-cells = <0>;
+ reg = <0x40000 0x40000>;
+ };
+
+EXAMPLE 2
+ /*
+ * The MPC8544 I2C controller node has an internal
+ * interrupt number of 27. As per the reference manual
+ * this corresponds to interrupt source configuration
+ * registers at 0x5_0560.
+ *
+ * The interrupt source configuration registers begin
+ * at 0x5_0000.
+ *
+ * To compute the interrupt specifier interrupt number
+ *
+ * 0x560 >> 5 = 43
+ *
+ * The interrupt source configuration registers begin
+ * at 0x5_0000, and so the i2c vector/priority registers
+ * are at 0x5_0560.
+ */
+ i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ compatible = "fsl-i2c";
+ reg = <0x3000 0x100>;
+ interrupts = <43 2>;
+ interrupt-parent = <&mpic>;
+ dfsrr;
+ };
+
+
+EXAMPLE 3
+ /*
+ * Definition of a node defining the 4
+ * MPIC IPI interrupts. Note the interrupt
+ * type of 2.
+ */
+ ipi@410a0 {
+ compatible = "fsl,mpic-ipi";
+ reg = <0x40040 0x10>;
+ interrupts = <0 0 2 0
+ 1 0 2 0
+ 2 0 2 0
+ 3 0 2 0>;
+ };
+
+EXAMPLE 4
+ /*
+ * Definition of a node defining the MPIC
+ * global timers. Note the interrupt
+ * type of 3.
+ */
+ timer0: timer@41100 {
+ compatible = "fsl,mpic-global-timer";
+ reg = <0x41100 0x100>;
+ interrupts = <0 0 3 0
+ 1 0 3 0
+ 2 0 3 0
+ 3 0 3 0>;
+ };
+
+EXAMPLE 5
+ /*
+ * Definition of an error interrupt (interupt type 1).
+ * SoC interrupt number is 16 and the specific error
+ * interrupt bit in the error interrupt summary register
+ * is 23.
+ */
+ memory-controller@8000 {
+ compatible = "fsl,p4080-memory-controller";
+ reg = <0x8000 0x1000>;
+ interrupts = <16 2 1 23>;
+ };
git.openpandora.org / pandora-kernel.git / blobdiff