Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
It could be done in exception-handling bits in __get_user_b() et.al.,
but the surgery involved would take more knowledge of sh64 details
than I have or _want_ to have.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
should clear on access_ok() failures. Also remove the useless
range truncation logics.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[bwh: Backported to 3.2: no calls to check_object_size()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
... that should zero on faults. Also remove the <censored> helpful
logics wrt range truncation copied from ppc32. Where it had ever
been needed only in case of copy_from_user() *and* had not been merged
into the mainline until a month after the need had disappeared.
A decade before openrisc went into mainline, I might add...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[bwh: Backported to 3.2: include <linux/string.h> to get declaration of memset()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[bwh: Backported to 3.2: no calls to check_object_size()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
* copy_from_user() on access_ok() failure ought to zero the destination
* none of those primitives should skip the access_ok() check in case of
small constant size.
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When we need to allocate a temporary blkcipher_walk_next and it
fails, the code is supposed to take the slow path of processing
the data block by block. However, due to an unrelated change
we instead end up dereferencing the NULL pointer.
This patch fixes it by moving the unrelated bsize setting out
of the way so that we enter the slow path as inteded.
Fixes: 7607bd8ff03b ("[CRYPTO] blkcipher: Added blkcipher_walk_virt_block") Reported-by: xiakaixu <xiakaixu@huawei.com> Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[bwh: Backported to 3.2: s/walk_blocksize/blocksize/] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
SA1111 PCMCIA was broken when PCMCIA switched to using dev_pm_ops for
the PCMCIA socket class. PCMCIA used to handle suspend/resume via the
socket hosting device, which happened at normal device suspend/resume
time.
However, the referenced commit changed this: much of the resume now
happens much earlier, in the noirq resume handler of dev_pm_ops.
However, on SA1111, the PCMCIA device is not accessible as the SA1111
has not been resumed at _noirq time. It's slightly worse than that,
because the SA1111 has already been put to sleep at _noirq time, so
suspend doesn't work properly.
Fix this by converting the core SA1111 code to use dev_pm_ops as well,
and performing its own suspend/resume at noirq time.
This fixes these errors in the kernel log:
pcmcia_socket pcmcia_socket0: time out after reset
pcmcia_socket pcmcia_socket1: time out after reset
and the resulting lack of PCMCIA cards after a S2RAM cycle.
Fixes: d7646f7632549 ("pcmcia: use dev_pm_ops for class pcmcia_socket_class") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Ensure that we conform to the algorithm described in RFC5661, section
18.36.4 for when to bump the sequence id. In essence we do it for all
cases except when the RPC call timed out, or in case of the server returning
NFS4ERR_DELAY or NFS4ERR_STALE_CLIENTID.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
[bwh: Backported to 3.2:
- Add the 'out' label
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This fixes subpage writes when using 4-bit HW ECC.
There has been numerous reports about ECC errors with devices using this
driver for a while. Also the 4-bit ECC has been reported as broken with
subpages in [1] and with 16 bits NANDs in the driver and in mach* board
files both in mainline and in the vendor BSPs.
What I saw with 4-bit ECC on a 16bits NAND (on an LCDK) which got me to
try reinitializing the ECC engine:
- R/W on whole pages properly generates/checks RS code
- try writing the 1st subpage only of a blank page, the subpage is well
written and the RS code properly generated, re-reading the same page
the HW detects some ECC error, reading the same page again no ECC
error is detected
Note that the ECC engine is already reinitialized in the 1-bit case.
Tested on my LCDK with UBI+UBIFS using subpages.
This could potentially get rid of the issue workarounded in [1].
[1] 28c015a9daab ("mtd: davinci-nand: disable subpage write for keystone-nand")
Fixes: 6a4123e581b3 ("mtd: nand: davinci_nand, 4-bit ECC for smallpage") Signed-off-by: Karl Beldan <kbeldan@baylibre.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
... in all cases, including the failing access_ok()
Note that some architectures using asm-generic/uaccess.h have
__copy_from_user() not zeroing the tail on failure halfway
through. This variant works either way.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When we fail to attach the security context in xfrm_state_construct()
we'll return 0 as error value which, in turn, will wrongly claim success
to userland when, in fact, we won't be adding / updating the XFRM state.
This is a regression introduced by commit fd21150a0fe1 ("[XFRM] netlink:
Inline attach_encap_tmpl(), attach_sec_ctx(), and attach_one_addr()").
Fix it by propagating the error returned by security_xfrm_state_alloc()
in this case.
When a seq-virmidi driver is initialized, it registers a rawmidi
instance with its callback to create an associated seq kernel client.
Currently it's done throughly in rawmidi's register_mutex context.
Recently it was found that this may lead to a deadlock another rawmidi
device that is being attached with the sequencer is accessed, as both
open with the same register_mutex. This was actually triggered by
syzkaller, as Dmitry Vyukov reported:
======================================================
[ INFO: possible circular locking dependency detected ]
4.8.0-rc1+ #11 Not tainted
-------------------------------------------------------
syz-executor/7154 is trying to acquire lock:
(register_mutex#5){+.+.+.}, at: [<ffffffff84fd6d4b>] snd_rawmidi_kernel_open+0x4b/0x260 sound/core/rawmidi.c:341
but task is already holding lock:
(&grp->list_mutex){++++.+}, at: [<ffffffff850138bb>] check_and_subscribe_port+0x5b/0x5c0 sound/core/seq/seq_ports.c:495
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
The fix is to simply move the registration parts in
snd_rawmidi_dev_register() to the outside of the register_mutex lock.
The lock is needed only to manage the linked list, and it's not
necessarily to cover the whole initialization process.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Although a similar issue was spotted and a fix patch was merged in
commit [6b760bb2c63a: ALSA: timer: fix division by zero after
SNDRV_TIMER_IOCTL_CONTINUE], it seems covering only a part of
iceberg.
In this patch, we fix the issue a bit more drastically. Basically the
continue of an uninitialized timer is supposed to be a fresh start, so
we do it for user timers. For the direct snd_timer_continue() call,
there is no way to pass the initial tick value, so we kick out for the
uninitialized case.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.2:
- Adjust context
- In _snd_timer_stop(), check the value of 'event' instead of 'stop'] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This is a minor code cleanup without any functional changes:
- Kill keep_flag argument from _snd_timer_stop(), as all callers pass
only it false.
- Remove redundant NULL check in _snd_timer_stop().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.2: adjust to apply after previously backported
"ALSA: timer: Fix race between stop and interrupt"] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When calling .import() on a cryptd ahash_request, the structure members
that describe the child transform in the shash_desc need to be initialized
like they are when calling .init()
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The origin of the issue I've seen is related to
a missing memory barrier between check for task->state and
the check for task->on_rq.
The task being woken up is already awake from a schedule()
and is doing the following:
do {
schedule()
set_current_state(TASK_(UN)INTERRUPTIBLE);
} while (!cond);
The waker, actually gets stuck doing the following in
try_to_wake_up():
while (p->on_cpu)
cpu_relax();
Analysis:
The instance I've seen involves the following race:
CPU1 CPU2
while () {
if (cond)
break;
do {
schedule();
set_current_state(TASK_UN..)
} while (!cond);
wakeup_routine()
spin_lock_irqsave(wait_lock)
raw_spin_lock_irqsave(wait_lock) wake_up_process()
} try_to_wake_up()
set_current_state(TASK_RUNNING); ..
list_del(&waiter.list);
CPU2 wakes up CPU1, but before it can get the wait_lock and set
current state to TASK_RUNNING the following occurs:
CPU3
wakeup_routine()
raw_spin_lock_irqsave(wait_lock)
if (!list_empty)
wake_up_process()
try_to_wake_up()
raw_spin_lock_irqsave(p->pi_lock)
..
if (p->on_rq && ttwu_wakeup())
..
while (p->on_cpu)
cpu_relax()
..
CPU3 tries to wake up the task on CPU1 again since it finds
it on the wait_queue, CPU1 is spinning on wait_lock, but immediately
after CPU2, CPU3 got it.
CPU3 checks the state of p on CPU1, it is TASK_UNINTERRUPTIBLE and
the task is spinning on the wait_lock. Interestingly since p->on_rq
is checked under pi_lock, I've noticed that try_to_wake_up() finds
p->on_rq to be 0. This was the most confusing bit of the analysis,
but p->on_rq is changed under runqueue lock, rq_lock, the p->on_rq
check is not reliable without this fix IMHO. The race is visible
(based on the analysis) only when ttwu_queue() does a remote wakeup
via ttwu_queue_remote. In which case the p->on_rq change is not
done uder the pi_lock.
The result is that after a while the entire system locks up on
the raw_spin_irqlock_save(wait_lock) and the holder spins infintely
Reproduction of the issue:
The issue can be reproduced after a long run on my system with 80
threads and having to tweak available memory to very low and running
memory stress-ng mmapfork test. It usually takes a long time to
reproduce. I am trying to work on a test case that can reproduce
the issue faster, but thats work in progress. I am still testing the
changes on my still in a loop and the tests seem OK thus far.
Big thanks to Benjamin and Nick for helping debug this as well.
Ben helped catch the missing barrier, Nick caught every missing
bit in my theory.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[ Updated comment to clarify matching barriers. Many
architectures do not have a full barrier in switch_to()
so that cannot be relied upon. ] Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Alexey Kardashevskiy <aik@ozlabs.ru> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nicholas Piggin <nicholas.piggin@gmail.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/e02cce7b-d9ca-1ad0-7a61-ea97c7582b37@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
All the scaling of the KXSD9 involves multiplication with a
fraction number < 1.
However the scaling value returned from IIO_INFO_SCALE was
unpredictable as only the micros of the value was assigned, and
not the integer part, resulting in scaling like this:
When a new CM connection is being requested, ipoib driver copies data
from the path pointer in the CM/tx object, the path object might be
invalid at the point and memory corruption will happened later when now
the CM driver will try using that data.
The next scenario demonstrates it:
neigh_add_path --> ipoib_cm_create_tx -->
queue_work (pointer to path is in the cm/tx struct)
#while the work is still in the queue,
#the port goes down and causes the ipoib_flush_paths:
ipoib_flush_paths --> path_free --> kfree(path)
#at this point the work scheduled starts.
ipoib_cm_tx_start --> copy from the (invalid)path pointer:
(memcpy(&pathrec, &p->path->pathrec, sizeof pathrec);)
-> memory corruption.
To fix that the driver now starts the CM/tx connection only if that
specific path exists in the general paths database.
This check is protected with the relevant locks, and uses the gid from
the neigh member in the CM/tx object which is valid according to the ref
count that was taken by the CM/tx.
Fixes: 839fcaba35 ('IPoIB: Connected mode experimental support') Signed-off-by: Erez Shitrit <erezsh@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
[bwh: Backported to 3.2: s/neigh->daddr/neigh->neighbour->ha/] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The function send_leave sets the member: group->query_id
(group->query_id = ret) after calling the sa_query, but leave_handler
can be executed before the setting and it might delete the group object,
and will get a memory corruption.
Additionally, this patch gets rid of group->query_id variable which is
not used.
Łukasz Daniluk reported that on a RHEL kernel that his machine would lock up
after enabling function tracer. I asked him to bisect the functions within
available_filter_functions, which he did and it came down to three:
_paravirt_nop(), _paravirt_ident_32() and _paravirt_ident_64()
It was found that this is only an issue when noreplace-paravirt is added
to the kernel command line.
This means that those functions are most likely called within critical
sections of the funtion tracer, and must not be traced.
In newer kenels _paravirt_nop() is defined within gcc asm(), and is no
longer an issue. But both _paravirt_ident_{32,64}() causes the
following splat when they are traced:
- ioctl(SNDRV_TIMER_IOCTL_SELECT), which potentially sets
tu->queue/tu->tqueue to NULL on memory allocation failure, so read()
would get a NULL pointer dereference like the above splat
- the same ioctl() can free tu->queue/to->tqueue which means read()
could potentially see (and dereference) the freed pointer
We can fix both by taking the ioctl_lock mutex when dereferencing
->queue/->tqueue, since that's always held over all the ioctl() code.
Just looking at the code I find it likely that there are more problems
here such as tu->qhead pointing outside the buffer if the size is
changed concurrently using SNDRV_TIMER_IOCTL_PARAMS.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.2: don't put_device() since snd_timer_instance_new()
doesn't take a device reference] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The problem happens when you call ioctl(SNDRV_TIMER_IOCTL_CONTINUE) on a
completely new/unused timer -- it will have ->sticks == 0, which causes a
divide by 0 in snd_hrtimer_callback().
seq_read() is a nasty piece of work, not to mention buggy.
It has (I think) an old bug which allows unprivileged userspace to read
beyond the end of m->buf.
I was getting these:
BUG: KASAN: slab-out-of-bounds in seq_read+0xcd2/0x1480 at addr ffff880116889880
Read of size 2713 by task trinity-c2/1329
CPU: 2 PID: 1329 Comm: trinity-c2 Not tainted 4.8.0-rc1+ #96
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014
Call Trace:
kasan_object_err+0x1c/0x80
kasan_report_error+0x2cb/0x7e0
kasan_report+0x4e/0x80
check_memory_region+0x13e/0x1a0
kasan_check_read+0x11/0x20
seq_read+0xcd2/0x1480
proc_reg_read+0x10b/0x260
do_loop_readv_writev.part.5+0x140/0x2c0
do_readv_writev+0x589/0x860
vfs_readv+0x7b/0xd0
do_readv+0xd8/0x2c0
SyS_readv+0xb/0x10
do_syscall_64+0x1b3/0x4b0
entry_SYSCALL64_slow_path+0x25/0x25
Object at ffff880116889100, in cache kmalloc-4096 size: 4096
Allocated:
PID = 1329
save_stack_trace+0x26/0x80
save_stack+0x46/0xd0
kasan_kmalloc+0xad/0xe0
__kmalloc+0x1aa/0x4a0
seq_buf_alloc+0x35/0x40
seq_read+0x7d8/0x1480
proc_reg_read+0x10b/0x260
do_loop_readv_writev.part.5+0x140/0x2c0
do_readv_writev+0x589/0x860
vfs_readv+0x7b/0xd0
do_readv+0xd8/0x2c0
SyS_readv+0xb/0x10
do_syscall_64+0x1b3/0x4b0
return_from_SYSCALL_64+0x0/0x6a
Freed:
PID = 0
(stack is not available)
Memory state around the buggy address: ffff88011688a000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff88011688a080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff88011688a100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^ ffff88011688a180: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88011688a200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Disabling lock debugging due to kernel taint
This seems to be the same thing that Dave Jones was seeing here:
https://lkml.org/lkml/2016/8/12/334
There are multiple issues here:
1) If we enter the function with a non-empty buffer, there is an attempt
to flush it. But it was not clearing m->from after doing so, which
means that if we try to do this flush twice in a row without any call
to traverse() in between, we are going to be reading from the wrong
place -- the splat above, fixed by this patch.
2) If there's a short write to userspace because of page faults, the
buffer may already contain multiple lines (i.e. pos has advanced by
more than 1), but we don't save the progress that was made so the
next call will output what we've already returned previously. Since
that is a much less serious issue (and I have a headache after
staring at seq_read() for the past 8 hours), I'll leave that for now.
Link: http://lkml.kernel.org/r/1471447270-32093-1-git-send-email-vegard.nossum@oracle.com Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Reported-by: Dave Jones <davej@codemonkey.org.uk> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
These product IDs are listed in Windows driver.
0x6803 corresponds to WeTelecom WM-D300.
0x6802 name is unknown.
Signed-off-by: Aleksandr Makarov <aleksandr.o.makarov@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
So IR table is setup even if "noapic" boot parameter is added. As a result we
crash later when the interrupt affinity is set due to a half initialized
remapping infrastructure.
Prevent remap initialization when IOAPIC is disabled.
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Joerg Roedel <joro@8bytes.org> Link: http://lkml.kernel.org/r/1471954039-3942-1-git-send-email-wanpeng.li@hotmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
An assertion in layout_in_gaps() verifies that the gap_lebs pointer is
below the maximum bound. When computing this maximum bound the idx_lebs
count is multiplied by sizeof(int), while C pointers arithmetic does take
into account the size of the pointed elements implicitly already. Remove
the multiplication to fix the assertion.
Fixes: 1e51764a3c2ac05a ("UBIFS: add new flash file system") Signed-off-by: Vincent Stehlé <vincent.stehle@intel.com> Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
UBSAN complains about a left shift by -1 in proc_do_submiturb(). This
can occur when an URB is submitted for a bulk or control endpoint on
a high-speed device, since the code doesn't bother to check the
endpoint type; normally only interrupt or isochronous endpoints have
a nonzero bInterval value.
Aside from the fact that the operation is illegal, it shouldn't matter
because the result isn't used. Still, in theory it could cause a
hardware exception or other problem, so we should work around it.
This patch avoids doing the left shift unless the shift amount is >= 0.
The same piece of code has another problem. When checking the device
speed (the exponential encoding for interrupt endpoints is used only
by high-speed or faster devices), we need to look for speed >=
USB_SPEED_SUPER as well as speed == USB_SPEED HIGH. The patch adds
this check.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Vittorio Zecca <zeccav@gmail.com> Tested-by: Vittorio Zecca <zeccav@gmail.com> Suggested-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Somehow this one slipped through, which means drivers without modeset
support can be oopsed (since those also don't call
drm_mode_config_init, which means the crtc lookup will chase an
uninitalized idr).
Reported-by: Alexander Potapenko <glider@google.com> Cc: Alexander Potapenko <glider@google.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Any readings from the raw interface of the KXSD9 driver will
return an empty string, because it does not return
IIO_VAL_INT but rather some random value from the accelerometer
to the caller.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Aleksandr Makarov <aleksandr.o.makarov@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When building gccgo in userspace, errno.h gets parsed and the go include file
sysinfo.go is generated.
Since EREFUSED is defined to the same value as ECONNREFUSED, and ECONNREFUSED
is defined later on in errno.h, this leads to go complaining that EREFUSED
isn't defined yet.
Fix this trivial problem by moving the define of EREFUSED down after
ECONNREFUSED in errno.h (and clean up the indenting while touching this line).
Signed-off-by: Helge Deller <deller@gmx.de>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The commit 4097461897df ("Input: i8042 - break load dependency ...")
correctly set up ps2_cmd_mutex pointer for the KBD port but forgot to do
the same for AUX port(s), which results in communication on KBD and AUX
ports to clash with each other.
Fixes: 4097461897df ("Input: i8042 - break load dependency ...") Reported-by: Bruno Wolff III <bruno@wolff.to> Tested-by: Bruno Wolff III <bruno@wolff.to> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This bug seems to be present for a very long time.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When tcp_sendmsg() allocates a fresh and empty skb, it puts it at the
tail of the write queue using tcp_add_write_queue_tail()
Then it attempts to copy user data into this fresh skb.
If the copy fails, we undo the work and remove the fresh skb.
Unfortunately, this undo lacks the change done to tp->highest_sack and
we can leave a dangling pointer (to a freed skb)
Later, tcp_xmit_retransmit_queue() can dereference this pointer and
access freed memory. For regular kernels where memory is not unmapped,
this might cause SACK bugs because tcp_highest_sack_seq() is buggy,
returning garbage instead of tp->snd_nxt, but with various debug
features like CONFIG_DEBUG_PAGEALLOC, this can crash the kernel.
This bug was found by Marco Grassi thanks to syzkaller.
Fixes: 6859d49475d4 ("[TCP]: Abstract tp->highest_sack accessing & point to next skb") Reported-by: Marco Grassi <marco.gra@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Cc: Yuchung Cheng <ycheng@google.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
After a device is disconnected, xhci_stop_device() will be invoked
in xhci_bus_suspend().
Also the "disconnect" IRQ will have ISR to invoke
xhci_free_virt_device() in this sequence.
xhci_irq -> xhci_handle_event -> handle_cmd_completion ->
xhci_handle_cmd_disable_slot -> xhci_free_virt_device
If xhci->devs[slot_id] has been assigned to NULL in
xhci_free_virt_device(), then virt_dev->eps[i].ring in
xhci_stop_device() may point to an invlid address to cause kernel
panic.
virt_dev = xhci->devs[slot_id];
:
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)
[ 187.235190] scsi host2: Avago SAS based MegaRAID driver
[ 191.112365] megaraid_sas 0000:89:00.0: BAR 0: can't reserve [io 0x0000-0x00ff]
[ 191.120548] megaraid_sas 0000:89:00.0: IO memory region busy!
and the card has resource like,
[ 125.097714] pci 0000:89:00.0: [1000:005d] type 00 class 0x010400
[ 125.104446] pci 0000:89:00.0: reg 0x10: [io 0x0000-0x00ff]
[ 125.110686] pci 0000:89:00.0: reg 0x14: [mem 0xce400000-0xce40ffff 64bit]
[ 125.118286] pci 0000:89:00.0: reg 0x1c: [mem 0xce300000-0xce3fffff 64bit]
[ 125.125891] pci 0000:89:00.0: reg 0x30: [mem 0xce200000-0xce2fffff pref]
that does not io port resource allocated from BIOS, and kernel can not
assign one as io port shortage.
The driver is only looking for MEM, and should not fail.
It turns out megasas_init_fw() etc are using bar index as mask. index 1
is used as mask 1, so that pci_request_selected_regions() is trying to
request BAR0 instead of BAR1.
Fix all related reference.
Fixes: b6d5d8808b4c ("megaraid_sas: Use lowest memory bar for SR-IOV VF support") Signed-off-by: Yinghai Lu <yinghai@kernel.org> Acked-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Usually current->mm (and therefore mm->pgd) stays the same during the
lifetime of a task so it does not matter if a task gets preempted during
the read and write of the CR3.
But then, there is this scenario on x86-UP:
TaskA is in do_exit() and exit_mm() sets current->mm = NULL followed by:
At this point current->mm is NULL but current->active_mm still points to
the "old" mm.
Let's preempt taskA _after_ native_read_cr3() by taskB. TaskB has its
own mm so CR3 has changed.
Now preempt back to taskA. TaskA has no ->mm set so it borrows taskB's
mm and so CR3 remains unchanged. Once taskA gets active it continues
where it was interrupted and that means it writes its old CR3 value
back. Everything is fine because userland won't need its memory
anymore.
Now the fun part:
Let's preempt taskA one more time and get back to taskB. This
time switch_mm() won't do a thing because oldmm (->active_mm)
is the same as mm (as per context_switch()). So we remain
with a bad CR3 / PGD and return to userland.
The next thing that happens is handle_mm_fault() with an address for
the execution of its code in userland. handle_mm_fault() realizes that
it has a PTE with proper rights so it returns doing nothing. But the
CPU looks at the wrong PGD and insists that something is wrong and
faults again. And again. And one more time…
This pagefault circle continues until the scheduler gets tired of it and
puts another task on the CPU. It gets little difficult if the task is a
RT task with a high priority. The system will either freeze or it gets
fixed by the software watchdog thread which usually runs at RT-max prio.
But waiting for the watchdog will increase the latency of the RT task
which is no good.
Fix this by disabling preemption across the critical code section.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Rik van Riel <riel@redhat.com> Acked-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Borislav Petkov <bp@suse.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mel Gorman <mgorman@suse.de> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/1470404259-26290-1-git-send-email-bigeasy@linutronix.de
[ Prettified the changelog. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When a device is in a status where CIO has killed all I/O by itself the
interrupt for a clear request may not contain an irb to determine the
clear function. Instead it contains an error pointer -EIO.
This was ignored by the DASD int_handler leading to a hanging device
waiting for a clear interrupt.
Handle -EIO error pointer correctly for requests that are clear pending and
treat the clear as successful.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com> Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Erroneous or malicious endpoint descriptors may have non-zero bits in
reserved positions, or out-of-bounds values. This patch helps prevent
these from causing problems by bounds-checking the wMaxPacketValue
entries in endpoint descriptors and capping the values at the maximum
allowed.
This issue was first discovered and tests were conducted by Jake Lamberson
<jake.lamberson1@gmail.com>, an intern working for Rosie Hall.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: roswest <roswest@cisco.com> Tested-by: roswest <roswest@cisco.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: drop the USB_SPEED_SUPER_PLUS case] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Like NFQNL_MSG_VERDICT_BATCH do, we should also reject the verdict
request when the portid is not same with the initial portid(maybe
from another process).
Fixes: 97d32cf9440d ("netfilter: nfnetlink_queue: batch verdict support") Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Reviewed-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In aacraid's ioctl_send_fib() we do two fetches from userspace, one the
get the fib header's size and one for the fib itself. Later we use the
size field from the second fetch to further process the fib. If for some
reason the size from the second fetch is different than from the first
fix, we may encounter an out-of- bounds access in aac_fib_send(). We
also check the sender size to insure it is not out of bounds. This was
reported in https://bugzilla.kernel.org/show_bug.cgi?id=116751 and was
assigned CVE-2016-6480.
Reported-by: Pengfei Wang <wpengfeinudt@gmail.com> Fixes: 7c00ffa31 '[SCSI] 2.6 aacraid: Variable FIB size (updated patch)' Signed-off-by: Dave Carroll <david.carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Bugzilla https://bugzilla.kernel.org/show_bug.cgi?id=105331
reports that the "AEO model 0" display is driven with 8 bpc
without dithering by default, which looks bad because that
panel is apparently a 6 bpc DP panel with faulty EDID.
A fix for this was made by commit 013dd9e03872
("drm/i915/dp: fall back to 18 bpp when sink capability is unknown").
That commit triggers new regressions in precision for DP->DVI and
DP->VGA displays. A patch is out to revert that commit, but it will
revert video output for the AEO model 0 panel to 8 bpc without
dithering.
The EDID 1.3 of that panel, as decoded from the xrandr output
attached to that bugzilla bug report, is somewhat faulty, and beyond
other problems also sets the "DFP 1.x compliant TMDS" bit, which
according to DFP spec means to drive the panel with 8 bpc and
no dithering in absence of other colorimetry information.
Try to make the original bug reporter happy despite the
faulty EDID by adding a quirk to mark that panel as 6 bpc,
so 6 bpc output with dithering creates a nice picture.
Tested by injecting the edid from the fdo bug into a DP connector
via drm_kms_helper.edid_firmware and verifying the 6 bpc + dithering
is selected.
This patch should be backported to stable.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
BCM20706V2_EVAL is a WICED dev board designed with FT2232H USB 2.0
UART/FIFO IC.
To support BCM920706V2_EVAL dev board for WICED development on Linux.
Add the VID(0a5c) and PID(6422) to ftdi_sio driver to allow loading
ftdi_sio for this board.
Signed-off-by: Sheng-Hui J. Chu <s.jeffrey.chu@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This problem can occur in the following situation:
open()
- pread()
- .seq_start()
- iter = kmalloc() // succeeds
- seqf->private = iter
- .seq_stop()
- kfree(seqf->private)
- pread()
- .seq_start()
- iter = kmalloc() // fails
- .seq_stop()
- class_dev_iter_exit(seqf->private) // boom! old pointer
As the comment in disk_seqf_stop() says, stop is called even if start
failed, so we need to reinitialise the private pointer to NULL when seq
iteration stops.
An alternative would be to set the private pointer to NULL when the
kmalloc() in disk_seqf_start() fails.
We can't pass error pointers to kfree() or it causes an oops.
Fixes: 52b209f7b848 ('get rid of hostfs_read_inode()') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In powerpc servers with large memory(32TB), we watched several soft
lockups for hugepage under stress tests.
The call traces are as follows:
1.
get_page_from_freelist+0x2d8/0xd50
__alloc_pages_nodemask+0x180/0xc20
alloc_fresh_huge_page+0xb0/0x190
set_max_huge_pages+0x164/0x3b0
When the corrupt_bio_byte feature was introduced it caused READ bios to
no longer be errored with -EIO during the down_interval. This had to do
with the complexity of needing to submit READs if the corrupt_bio_byte
feature was used.
Fix it so READ bios are properly errored with -EIO; doing so early in
flakey_map() as long as there isn't a match for the corrupt_bio_byte
feature.
Fixes: a3998799fb4df ("dm flakey: add corrupt_bio_byte feature") Reported-by: Akira Hayakawa <ruby.wktk@gmail.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[bwh: Backported to 3.2: in flakey_end_io(), keep using
bio_submitted_while_down instead of pb->bio_submitted] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The balloon has a special mechanism that is subscribed to the oom
notification which leads to deflation for a fixed number of pages.
The number is always fixed even when the balloon is fully deflated.
But leak_balloon did not expect that the pages to deflate will be more
than taken, and raise a "BUG" in balloon_page_dequeue when page list
will be empty.
So, the simplest solution would be to check that the number of releases
pages is less or equal to the number taken pages.
Signed-off-by: Konstantin Neumoin <kneumoin@virtuozzo.com> Signed-off-by: Denis V. Lunev <den@openvz.org> CC: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
x86_64 needs to use compat_sys_keyctl for 32-bit userspace rather than
calling sys_keyctl(). The latter will work in a lot of cases, thereby
hiding the issue.
Reported-by: Stephan Mueller <smueller@chronox.de> Tested-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: David Howells <dhowells@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: keyrings@vger.kernel.org Cc: linux-security-module@vger.kernel.org Link: http://lkml.kernel.org/r/146961615805.14395.5581949237156769439.stgit@warthog.procyon.org.uk Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.2: compat system call table is in ia32entry.S] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
AT_VECTOR_SIZE_ARCH should be defined with the maximum number of
NEW_AUX_ENT entries that ARCH_DLINFO can contain, but it wasn't defined
for s390 at all even though ARCH_DLINFO can contain one NEW_AUX_ENT when
VDSO is enabled.
This shouldn't be a problem as AT_VECTOR_SIZE_BASE includes space for
AT_BASE_PLATFORM which s390 doesn't use, but lets define it now and add
the comment above ARCH_DLINFO as found in several other architectures to
remind future modifiers of ARCH_DLINFO to keep AT_VECTOR_SIZE_ARCH up to
date.
Fixes: b020632e40c3 ("[S390] introduce vdso on s390") Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: linux-s390@vger.kernel.org
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
tcp_select_initial_window() intends to advertise a window
scaling for the maximum possible window size. To do so,
it considers the maximum of net.ipv4.tcp_rmem[2] and
net.core.rmem_max as the only possible upper-bounds.
However, users with CAP_NET_ADMIN can use SO_RCVBUFFORCE
to set the socket's receive buffer size to values
larger than net.ipv4.tcp_rmem[2] and net.core.rmem_max.
Thus, SO_RCVBUFFORCE is effectively ignored by
tcp_select_initial_window().
To fix this, consider the maximum of net.ipv4.tcp_rmem[2],
net.core.rmem_max and socket's initial buffer space.
Fixes: b0573dea1fb3 ("[NET]: Introduce SO_{SND,RCV}BUFFORCE socket options") Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Suggested-by: Neal Cardwell <ncardwell@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
MIPS64 needs to use compat_sys_keyctl for 32-bit userspace rather than
calling sys_keyctl. The latter will work in a lot of cases, thereby hiding
the issue.
Reported-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: David Howells <dhowells@redhat.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Cc: linux-security-module@vger.kernel.org Cc: keyrings@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13832/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ceph_llseek does not correctly return NXIO errors because the 'out' path
always returns 'offset'.
Fixes: 06222e491e66 ("fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek") Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com> Signed-off-by: Yan, Zheng <zyan@redhat.com>
[bwh: Backported to 3.2:
- We don't use vfs_setpos(); instead set ret = -EINVAL or ret = offset
directly
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
As explained in 1407814240-4275-1-git-send-email-decui@microsoft.com we
have a hard load dependency between i8042 and atkbd which prevents
keyboard from working on Gen2 Hyper-V VMs.
> hyperv_keyboard invokes serio_interrupt(), which needs a valid serio
> driver like atkbd.c. atkbd.c depends on libps2.c because it invokes
> ps2_command(). libps2.c depends on i8042.c because it invokes
> i8042_check_port_owner(). As a result, hyperv_keyboard actually
> depends on i8042.c.
>
> For a Generation 2 Hyper-V VM (meaning no i8042 device emulated), if a
> Linux VM (like Arch Linux) happens to configure CONFIG_SERIO_I8042=m
> rather than =y, atkbd.ko can't load because i8042.ko can't load(due to
> no i8042 device emulated) and finally hyperv_keyboard can't work and
> the user can't input: https://bugs.archlinux.org/task/39820
> (Ubuntu/RHEL/SUSE aren't affected since they use CONFIG_SERIO_I8042=y)
To break the dependency we move away from using i8042_check_port_owner()
and instead allow serio port owner specify a mutex that clients should use
to serialize PS/2 command stream.
Reported-by: Mark Laws <mdl@60hz.org> Tested-by: Mark Laws <mdl@60hz.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If 'tunnel' is NULL we should return -EBADF but the 'end_put_sess' path
unconditionally sets 'error' back to zero. Rework the error path so it
more closely matches pppol2tp_sendmsg.
Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The problem is that irda_open_tsap() can fail and leave self->tsap = NULL,
and then irttp_connect_request() almost immediately dereferences it.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
NFS doesn't expect requests with wb_bytes set to zero and may make
unexpected decisions about how to handle that request at the page IO layer.
Skip request creation if we won't have any wb_bytes in the request.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Reviewed-by: Weston Andros Adamson <dros@primarydata.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The size of individual keymap in drivers/tty/vt/keyboard.c is NR_KEYS,
which is currently 256, whereas number of keys/buttons in input device (and
therefor in key_down) is much larger - KEY_CNT - 768, and that can cause
out-of-bound access when we do
sym = U(key_maps[0][k]);
with large 'k'.
To fix it we should not attempt iterating beyond smaller of NR_KEYS and
KEY_CNT.
Also while at it let's switch to for_each_set_bit() instead of open-coding
it.
According to the datasheet you should only write 1 to this bit. If it is
not set, at least AIN3 will return bad values on newer silicon revisions.
Fixes: d84ca5b345c2 ("hwmon: Add driver for ADT7411 voltage and temperature sensor") Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
nand_do_write_ops() determines if it is writing a partial page with the
formula:
part_pagewr = (column || writelen < (mtd->writesize - 1))
When 'writelen' is exactly 1 byte less than the NAND page size the formula
equates to zero, so the code doesn't process it as a partial write,
although it should.
As a consequence the function remains in the while(1) loop with 'writelen'
becoming 0xffffffff and iterating endlessly.
The bug may not be easy to reproduce in Linux since user space tools
usually force the padding or round-up the write size to a page-size
multiple.
This was discovered in U-Boot where the issue can be reproduced by
writing any size that is 1 byte less than a page-size multiple.
For example, on a NAND with 2K page (0x800):
=> nand erase.part <partition>
=> nand write $loadaddr <partition> 7ff
[Editor's note: the bug was added in commit 29072b96078f, but moved
around in commit 66507c7bc8895 ("mtd: nand: Add support to use nand_base
poi databuf as bounce buffer")]
Fixes: 29072b96078f ("[MTD] NAND: add subpage write support") Signed-off-by: Hector Palacios <hector.palacios@digi.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[bwh: Backported to 3.2: adjusted context as noted above] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
wlc_phy_txpower_get_current() does a logical OR of power->flags, which
presumes that power.flags was initiliazed earlier by the caller,
unfortunately, this is not the case, so make sure we zero out the struct
tx_power before calling into wlc_phy_txpower_get_current().
Reported-by: coverity (CID 146011) Fixes: 5b435de0d7868 ("net: wireless: add brcm80211 drivers") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Some chips incorrectly support partial reads from TPM_STS register
at non-zero offsets. Read the entire 32-bits register instead of
making two 8-bit reads to support such devices and reduce the number
of bus transactions when obtaining the burstcount from TPM_STS.
Fixes: 27084efee0c3 ("tpm: driver for next generation TPM chips") Signed-off-by: Andrey Pronin <apronin@chromium.org> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
[bwh: Backported to 3.2:
- Use raw ioread32() instead of tpm_tis_read32()
- Adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When there is more data to be processed, the current test in
scatterwalk_done may prevent us from calling pagedone even when
we should.
In particular, if we're on an SG entry spanning multiple pages
where the last page is not a full page, we will incorrectly skip
calling pagedone on the second last page.
This patch fixes this by adding a separate test for whether we've
reached the end of a page.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When we retrieve imtu value from userspace we should use 16 bit pointer
cast instead of 32 as it's defined that way in headers. Fixes setsockopt
calls on big-endian platforms.
There is a cut and paste issue here. The bug is that we are allocating
more memory than necessary for msp_maps. We should be allocating enough
space for a map_info struct (144 bytes) but we instead allocate enough
for an mtd_info struct (1840 bytes). It's a small waste.
The other part of this is not harmful but when we allocated msp_flash
then we allocated enough space fro a map_info pointer instead of an
mtd_info pointer. But since pointers are the same size it works out
fine.
Anyway, I decided to clean up all three allocations a bit to make them
a bit more consistent and clear.
Fixes: 68aa0fa87f6d ('[MTD] PMC MSP71xx flash/rootfs mappings') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If we encounter a filesystem error during orphan cleanup, we should stop.
Otherwise, we may end up in an infinite loop where the same inode is
processed again and again.
EXT4-fs (loop0): warning: checktime reached, running e2fsck is recommended
EXT4-fs error (device loop0): ext4_mb_generate_buddy:758: group 2, block bitmap and bg descriptor inconsistent: 6117 vs 0 free clusters
Aborting journal on device loop0-8.
EXT4-fs (loop0): Remounting filesystem read-only
EXT4-fs error (device loop0) in ext4_free_blocks:4895: Journal has aborted
EXT4-fs error (device loop0) in ext4_do_update_inode:4893: Journal has aborted
EXT4-fs error (device loop0) in ext4_do_update_inode:4893: Journal has aborted
EXT4-fs error (device loop0) in ext4_ext_remove_space:3068: IO failure
EXT4-fs error (device loop0) in ext4_ext_truncate:4667: Journal has aborted
EXT4-fs error (device loop0) in ext4_orphan_del:2927: Journal has aborted
EXT4-fs error (device loop0) in ext4_do_update_inode:4893: Journal has aborted
EXT4-fs (loop0): Inode 16 (00000000618192a0): orphan list check failed!
[...]
EXT4-fs (loop0): Inode 16 (0000000061819748): orphan list check failed!
[...]
EXT4-fs (loop0): Inode 16 (0000000061819bf0): orphan list check failed!
[...]
See-also: c9eb13a9105 ("ext4: fix hang when processing corrupted orphaned inode list") Cc: Jan Kara <jack@suse.cz> Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If we hit this error when mounted with errors=continue or
errors=remount-ro:
EXT4-fs error (device loop0): ext4_mb_mark_diskspace_used:2940: comm ext4.exe: Allocating blocks 5090-6081 which overlap fs metadata
then ext4_mb_new_blocks() will call ext4_mb_release_context() and try to
continue. However, ext4_mb_release_context() is the wrong thing to call
here since we are still actually using the allocation context.
Instead, just error out. We could retry the allocation, but there is a
possibility of getting stuck in an infinite loop instead, so this seems
safer.
[ Fixed up so we don't return EAGAIN to userspace. --tytso ]
Fixes: 8556e8f3b6 ("ext4: Don't allow new groups to be added during block allocation") Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[bwh: Backported to 3.2:
- Use EIO instead of EFSCORRUPTED
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When freeing the nested resources of a vcpu, there is an assumption that
the vcpu's vmcs01 is the current VMCS on the CPU that executes
nested_release_vmcs12(). If this assumption is violated, the vcpu's
vmcs01 may be made active on multiple CPUs at the same time, in
violation of Intel's specification. Moreover, since the vcpu's vmcs01 is
not VMCLEARed on every CPU on which it is active, it can linger in a
CPU's VMCS cache after it has been freed and potentially
repurposed. Subsequent eviction from the CPU's VMCS cache on a capacity
miss can result in memory corruption.
It is not sufficient for vmx_free_vcpu() to call vmx_load_vmcs01(). If
the vcpu in question was last loaded on a different CPU, it must be
migrated to the current CPU before calling vmx_load_vmcs01().
Signed-off-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 3.2: vcpu_load() returns void] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
free_nested needs the loaded_vmcs to be valid if it is a vmcs02, in
order to detach it from the shadow vmcs. However, this is not
available anymore after commit 26a865f4aa8e (KVM: VMX: fix use after
free of vmx->loaded_vmcs, 2014-01-03).
Revert that patch, and fix its problem by forcing a vmcs01 as the
active VMCS before freeing all the nested VMX state.
Reported-by: Wanpeng Li <wanpeng.li@linux.intel.com> Tested-by: Wanpeng Li <wanpeng.li@linux.intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
projects / pandora-kernel.git / log