* %NL80211_ATTR_WIPHY_CHANNEL_TYPE, %NL80211_ATTR_WIPHY_RETRY_SHORT,
* %NL80211_ATTR_WIPHY_RETRY_LONG, %NL80211_ATTR_WIPHY_FRAG_THRESHOLD,
* and/or %NL80211_ATTR_WIPHY_RTS_THRESHOLD.
+ * However, for setting the channel, see %NL80211_CMD_SET_CHANNEL
+ * instead, the support here is for backward compatibility only.
* @NL80211_CMD_NEW_WIPHY: Newly created wiphy, response to get request
* or rename notification. Has attributes %NL80211_ATTR_WIPHY and
* %NL80211_ATTR_WIPHY_NAME.
* %NL80211_ATTR_REG_RULE_POWER_MAX_ANT_GAIN and
* %NL80211_ATTR_REG_RULE_POWER_MAX_EIRP.
* @NL80211_CMD_REQ_SET_REG: ask the wireless core to set the regulatory domain
- * to the the specified ISO/IEC 3166-1 alpha2 country code. The core will
+ * to the specified ISO/IEC 3166-1 alpha2 country code. The core will
* store this as a valid request and then query userspace for it.
*
* @NL80211_CMD_GET_MESH_PARAMS: Get mesh networking properties for the
* @NL80211_CMD_NOTIFY_CQM: Connection quality monitor notification. This
* command is used as an event to indicate the that a trigger level was
* reached.
+ * @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ
+ * and %NL80211_ATTR_WIPHY_CHANNEL_TYPE) the given interface (identifed
+ * by %NL80211_ATTR_IFINDEX) shall operate on.
+ * In case multiple channels are supported by the device, the mechanism
+ * with which it switches channels is implementation-defined.
+ * When a monitor interface is given, it can only switch channel while
+ * no other interfaces are operating to avoid disturbing the operation
+ * of any other interfaces, and other interfaces will again take
+ * precedence when they are used.
*
* @NL80211_CMD_MAX: highest used command number
* @__NL80211_CMD_AFTER_LAST: internal use
NL80211_CMD_SET_CQM,
NL80211_CMD_NOTIFY_CQM,
+ NL80211_CMD_SET_CHANNEL,
+
/* add new commands above here */
/* used to define NL80211_CMD_MAX below */
* @NL80211_ATTR_CQM: connection quality monitor configuration in a
* nested attribute with %NL80211_ATTR_CQM_* sub-attributes.
*
+ * @NL80211_ATTR_LOCAL_STATE_CHANGE: Flag attribute to indicate that a command
+ * is requesting a local authentication/association state change without
+ * invoking actual management frame exchange. This can be used with
+ * NL80211_CMD_AUTHENTICATE, NL80211_CMD_DEAUTHENTICATE,
+ * NL80211_CMD_DISASSOCIATE.
+ *
+ * @NL80211_ATTR_AP_ISOLATE: (AP mode) Do not forward traffic between stations
+ * connected to this BSS.
+ *
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
*/
NL80211_ATTR_CQM,
+ NL80211_ATTR_LOCAL_STATE_CHANGE,
+
+ NL80211_ATTR_AP_ISOLATE,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH,
};
+
+/**
+ * enum nl80211_tx_power_setting - TX power adjustment
+ * @NL80211_TX_POWER_AUTOMATIC: automatically determine transmit power
+ * @NL80211_TX_POWER_LIMITED: limit TX power by the mBm parameter
+ * @NL80211_TX_POWER_FIXED: fix TX power to the mBm parameter
+ */
+enum nl80211_tx_power_setting {
+ NL80211_TX_POWER_AUTOMATIC,
+ NL80211_TX_POWER_LIMITED,
+ NL80211_TX_POWER_FIXED,
+};
+
#endif /* __LINUX_NL80211_H */