__u8 data[0];
};
-/* for configuring coalescing parameters of chip */
+/**
+ * struct ethtool_coalesce - coalescing parameters for IRQs and stats updates
+ * @cmd: ETHTOOL_{G,S}COALESCE
+ * @rx_coalesce_usecs: How many usecs to delay an RX interrupt after
+ * a packet arrives.
+ * @rx_max_coalesced_frames: Maximum number of packets to receive
+ * before an RX interrupt.
+ * @rx_coalesce_usecs_irq: Same as @rx_coalesce_usecs, except that
+ * this value applies while an IRQ is being serviced by the host.
+ * @rx_max_coalesced_frames_irq: Same as @rx_max_coalesced_frames,
+ * except that this value applies while an IRQ is being serviced
+ * by the host.
+ * @tx_coalesce_usecs: How many usecs to delay a TX interrupt after
+ * a packet is sent.
+ * @tx_max_coalesced_frames: Maximum number of packets to be sent
+ * before a TX interrupt.
+ * @tx_coalesce_usecs_irq: Same as @tx_coalesce_usecs, except that
+ * this value applies while an IRQ is being serviced by the host.
+ * @tx_max_coalesced_frames_irq: Same as @tx_max_coalesced_frames,
+ * except that this value applies while an IRQ is being serviced
+ * by the host.
+ * @stats_block_coalesce_usecs: How many usecs to delay in-memory
+ * statistics block updates. Some drivers do not have an
+ * in-memory statistic block, and in such cases this value is
+ * ignored. This value must not be zero.
+ * @use_adaptive_rx_coalesce: Enable adaptive RX coalescing.
+ * @use_adaptive_tx_coalesce: Enable adaptive TX coalescing.
+ * @pkt_rate_low: Threshold for low packet rate (packets per second).
+ * @rx_coalesce_usecs_low: How many usecs to delay an RX interrupt after
+ * a packet arrives, when the packet rate is below @pkt_rate_low.
+ * @rx_max_coalesced_frames_low: Maximum number of packets to be received
+ * before an RX interrupt, when the packet rate is below @pkt_rate_low.
+ * @tx_coalesce_usecs_low: How many usecs to delay a TX interrupt after
+ * a packet is sent, when the packet rate is below @pkt_rate_low.
+ * @tx_max_coalesced_frames_low: Maximum nuumber of packets to be sent before
+ * a TX interrupt, when the packet rate is below @pkt_rate_low.
+ * @pkt_rate_high: Threshold for high packet rate (packets per second).
+ * @rx_coalesce_usecs_high: How many usecs to delay an RX interrupt after
+ * a packet arrives, when the packet rate is above @pkt_rate_high.
+ * @rx_max_coalesced_frames_high: Maximum number of packets to be received
+ * before an RX interrupt, when the packet rate is above @pkt_rate_high.
+ * @tx_coalesce_usecs_high: How many usecs to delay a TX interrupt after
+ * a packet is sent, when the packet rate is above @pkt_rate_high.
+ * @tx_max_coalesced_frames_high: Maximum number of packets to be sent before
+ * a TX interrupt, when the packet rate is above @pkt_rate_high.
+ * @rate_sample_interval: How often to do adaptive coalescing packet rate
+ * sampling, measured in seconds. Must not be zero.
+ *
+ * Each pair of (usecs, max_frames) fields specifies this exit
+ * condition for interrupt coalescing:
+ * (usecs > 0 && time_since_first_completion >= usecs) ||
+ * (max_frames > 0 && completed_frames >= max_frames)
+ * It is illegal to set both usecs and max_frames to zero as this
+ * would cause interrupts to never be generated. To disable
+ * coalescing, set usecs = 0 and max_frames = 1.
+ *
+ * Some implementations ignore the value of max_frames and use the
+ * condition:
+ * time_since_first_completion >= usecs
+ * This is deprecated. Drivers for hardware that does not support
+ * counting completions should validate that max_frames == !rx_usecs.
+ *
+ * Adaptive RX/TX coalescing is an algorithm implemented by some
+ * drivers to improve latency under low packet rates and improve
+ * throughput under high packet rates. Some drivers only implement
+ * one of RX or TX adaptive coalescing. Anything not implemented by
+ * the driver causes these values to be silently ignored.
+ *
+ * When the packet rate is below @pkt_rate_high but above
+ * @pkt_rate_low (both measured in packets per second) the
+ * normal {rx,tx}_* coalescing parameters are used.
+ */
struct ethtool_coalesce {
- __u32 cmd; /* ETHTOOL_{G,S}COALESCE */
-
- /* How many usecs to delay an RX interrupt after
- * a packet arrives. If 0, only rx_max_coalesced_frames
- * is used.
- */
+ __u32 cmd;
__u32 rx_coalesce_usecs;
-
- /* How many packets to delay an RX interrupt after
- * a packet arrives. If 0, only rx_coalesce_usecs is
- * used. It is illegal to set both usecs and max frames
- * to zero as this would cause RX interrupts to never be
- * generated.
- */
__u32 rx_max_coalesced_frames;
-
- /* Same as above two parameters, except that these values
- * apply while an IRQ is being serviced by the host. Not
- * all cards support this feature and the values are ignored
- * in that case.
- */
__u32 rx_coalesce_usecs_irq;
__u32 rx_max_coalesced_frames_irq;
-
- /* How many usecs to delay a TX interrupt after
- * a packet is sent. If 0, only tx_max_coalesced_frames
- * is used.
- */
__u32 tx_coalesce_usecs;
-
- /* How many packets to delay a TX interrupt after
- * a packet is sent. If 0, only tx_coalesce_usecs is
- * used. It is illegal to set both usecs and max frames
- * to zero as this would cause TX interrupts to never be
- * generated.
- */
__u32 tx_max_coalesced_frames;
-
- /* Same as above two parameters, except that these values
- * apply while an IRQ is being serviced by the host. Not
- * all cards support this feature and the values are ignored
- * in that case.
- */
__u32 tx_coalesce_usecs_irq;
__u32 tx_max_coalesced_frames_irq;
-
- /* How many usecs to delay in-memory statistics
- * block updates. Some drivers do not have an in-memory
- * statistic block, and in such cases this value is ignored.
- * This value must not be zero.
- */
__u32 stats_block_coalesce_usecs;
-
- /* Adaptive RX/TX coalescing is an algorithm implemented by
- * some drivers to improve latency under low packet rates and
- * improve throughput under high packet rates. Some drivers
- * only implement one of RX or TX adaptive coalescing. Anything
- * not implemented by the driver causes these values to be
- * silently ignored.
- */
__u32 use_adaptive_rx_coalesce;
__u32 use_adaptive_tx_coalesce;
-
- /* When the packet rate (measured in packets per second)
- * is below pkt_rate_low, the {rx,tx}_*_low parameters are
- * used.
- */
__u32 pkt_rate_low;
__u32 rx_coalesce_usecs_low;
__u32 rx_max_coalesced_frames_low;
__u32 tx_coalesce_usecs_low;
__u32 tx_max_coalesced_frames_low;
-
- /* When the packet rate is below pkt_rate_high but above
- * pkt_rate_low (both measured in packets per second) the
- * normal {rx,tx}_* coalescing parameters are used.
- */
-
- /* When the packet rate is (measured in packets per second)
- * is above pkt_rate_high, the {rx,tx}_*_high parameters are
- * used.
- */
__u32 pkt_rate_high;
__u32 rx_coalesce_usecs_high;
__u32 rx_max_coalesced_frames_high;
__u32 tx_coalesce_usecs_high;
__u32 tx_max_coalesced_frames_high;
-
- /* How often to do adaptive coalescing packet rate sampling,
- * measured in seconds. Must not be zero.
- */
__u32 rate_sample_interval;
};
};
/**
- * struct ethtool_rx_flow_spec - specification for RX flow filter
+ * struct ethtool_rx_flow_spec - classification rule for RX flows
* @flow_type: Type of match to perform, e.g. %TCP_V4_FLOW
* @h_u: Flow fields to match (dependent on @flow_type)
* @h_ext: Additional fields to match
* includes the %FLOW_EXT flag.
* @ring_cookie: RX ring/queue index to deliver to, or %RX_CLS_FLOW_DISC
* if packets should be discarded
- * @location: Index of filter in hardware table
+ * @location: Location of rule in the table. Locations must be
+ * numbered such that a flow matching multiple rules will be
+ * classified according to the first (lowest numbered) rule.
*/
struct ethtool_rx_flow_spec {
__u32 flow_type;
* %ETHTOOL_GRXCLSRLALL, %ETHTOOL_SRXCLSRLDEL or %ETHTOOL_SRXCLSRLINS
* @flow_type: Type of flow to be affected, e.g. %TCP_V4_FLOW
* @data: Command-dependent value
- * @fs: Flow filter specification
+ * @fs: Flow classification rule
* @rule_cnt: Number of rules to be affected
- * @rule_locs: Array of valid rule indices
+ * @rule_locs: Array of used rule locations
*
* For %ETHTOOL_GRXFH and %ETHTOOL_SRXFH, @data is a bitmask indicating
* the fields included in the flow hash, e.g. %RXH_IP_SRC. The following
* For %ETHTOOL_GRXCLSRLCNT, @rule_cnt is set to the number of defined
* rules on return.
*
- * For %ETHTOOL_GRXCLSRULE, @fs.@location specifies the index of an
- * existing filter rule on entry and @fs contains the rule on return.
+ * For %ETHTOOL_GRXCLSRULE, @fs.@location specifies the location of an
+ * existing rule on entry and @fs contains the rule on return.
*
* For %ETHTOOL_GRXCLSRLALL, @rule_cnt specifies the array size of the
* user buffer for @rule_locs on entry. On return, @data is the size
- * of the filter table and @rule_locs contains the indices of the
- * defined rules.
+ * of the rule table, @rule_cnt is the number of defined rules, and
+ * @rule_locs contains the locations of the defined rules. Drivers
+ * must use the second parameter to get_rxnfc() instead of @rule_locs.
*
- * For %ETHTOOL_SRXCLSRLINS, @fs specifies the filter rule to add or
- * update. @fs.@location specifies the index to use and must not be
- * ignored.
+ * For %ETHTOOL_SRXCLSRLINS, @fs specifies the rule to add or update.
+ * @fs.@location specifies the location to use and must not be ignored.
*
- * For %ETHTOOL_SRXCLSRLDEL, @fs.@location specifies the index of an
- * existing filter rule on entry.
- *
- * Implementation of indexed classification rules generally requires a
- * TCAM.
+ * For %ETHTOOL_SRXCLSRLDEL, @fs.@location specifies the location of an
+ * existing rule on entry.
*/
struct ethtool_rxnfc {
__u32 cmd;
/* needed by dev_disable_lro() */
extern int __ethtool_set_flags(struct net_device *dev, u32 flags);
+extern int __ethtool_get_settings(struct net_device *dev,
+ struct ethtool_cmd *cmd);
+
/**
* enum ethtool_phys_id_state - indicator state for physical identification
* @ETHTOOL_ID_INACTIVE: Physical ID indicator should be deactivated
int (*set_priv_flags)(struct net_device *, u32);
int (*get_sset_count)(struct net_device *, int);
int (*get_rxnfc)(struct net_device *,
- struct ethtool_rxnfc *, void *);
+ struct ethtool_rxnfc *, u32 *rule_locs);
int (*set_rxnfc)(struct net_device *, struct ethtool_rxnfc *);
int (*flash_device)(struct net_device *, struct ethtool_flash *);
int (*reset)(struct net_device *, u32 *);
#define SPEED_1000 1000
#define SPEED_2500 2500
#define SPEED_10000 10000
+#define SPEED_UNKNOWN -1
/* Duplex, half or full. */
#define DUPLEX_HALF 0x00
#define DUPLEX_FULL 0x01
+#define DUPLEX_UNKNOWN 0xff
/* Which connector port. */
#define PORT_TP 0x00
git.openpandora.org / pandora-kernel.git / blobdiff