/*
* Top level Makefile configuration choices
*/
-#ifdef CONFIG_MK_PCI
-#define CONFIG_PCI
+#ifdef CONFIG_PCI
#define CONFIG_PCI1
#endif
-#ifdef CONFIG_MK_66
+#ifdef CONFIG_66
#define CONFIG_SYS_CLK_DIV 1
#endif
-#ifdef CONFIG_MK_33
+#ifdef CONFIG_33
#define CONFIG_SYS_CLK_DIV 2
#endif
-#ifdef CONFIG_MK_PCIE
+#ifdef CONFIG_PCIE
#define CONFIG_PCIE1
#endif
#define CONFIG_MPC8548 1 /* MPC8548 specific */
#define CONFIG_SBC8548 1 /* SBC8548 board specific */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xfffa0000
+#endif
+
#undef CONFIG_RIO
#ifdef CONFIG_PCI
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR 0xe0000000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
#define CONFIG_FSL_DDR2
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */
#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 /* relocate boot L2SRAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*
* For soldered on flash, (128kB/sector) we use 2 sectors for u-boot and
- * one for env+bootpg (TEXT_BASE=0xfffa_0000, 384kB total). For SODIMM
+ * one for env+bootpg (CONFIG_SYS_TEXT_BASE=0xfffa_0000, 384kB total). For SODIMM
* flash (512kB/sector) we use 1 sector for u-boot, and one for env+bootpg
- * (TEXT_BASE=0xfff0_0000, 1MB total). This dynamically sets the right
+ * (CONFIG_SYS_TEXT_BASE=0xfff0_0000, 1MB total). This dynamically sets the right
* thing for MONITOR_LEN in both cases.
*/
-#define CONFIG_SYS_MONITOR_LEN (~TEXT_BASE + 1)
+#define CONFIG_SYS_MONITOR_LEN (~CONFIG_SYS_TEXT_BASE + 1)
#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#if defined(CONFIG_PCI)
-#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#undef CONFIG_EEPRO100
#if defined(CONFIG_TSEC_ENET)
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 1
-#endif
-
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "eTSEC0"
*/
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_SIZE 0x2000
-#if TEXT_BASE == 0xfff00000 /* Boot from 64MB SODIMM */
+#if CONFIG_SYS_TEXT_BASE == 0xfff00000 /* Boot from 64MB SODIMM */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x80000)
#define CONFIG_ENV_SECT_SIZE 0x80000 /* 512K(one sector) for env */
-#elif TEXT_BASE == 0xfffa0000 /* Boot from 8MB soldered flash */
+#elif CONFIG_SYS_TEXT_BASE == 0xfffa0000 /* Boot from 8MB soldered flash */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
#else
* Miscellaneous configurable options
*/
#define CONFIG_CMDLINE_EDITING /* undef to save memory */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#define CONFIG_IPADDR 192.168.0.55
#define CONFIG_HOSTNAME sbc8548
-#define CONFIG_ROOTPATH /opt/eldk/ppc_85xx
-#define CONFIG_BOOTFILE /uImage
+#define CONFIG_ROOTPATH "/opt/eldk/ppc_85xx"
+#define CONFIG_BOOTFILE "/uImage"
#define CONFIG_UBOOTPATH /u-boot.bin /* TFTP server */
#define CONFIG_SERVERIP 192.168.0.2
"netdev=eth0\0" \
"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
"tftpflash=tftpboot $loadaddr $uboot; " \
- "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
- "erase " MK_STR(TEXT_BASE) " +$filesize; " \
- "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
- "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
- "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
+ "protect off " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
+ "erase " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
+ "cp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize; " \
+ "protect on " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
+ "cmp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=2000000\0" \
"ramdiskfile=uRamdisk\0" \
git.openpandora.org / pandora-u-boot.git / blobdiff