pci: Move CONFIG_PCI_PNP to Kconfig

[pandora-u-boot.git] / include / configs / db-88f6820-gp.h

diff --git a/include/configs/db-88f6820-gp.h b/include/configs/db-88f6820-gp.h
index d76ceb7..72c38e2 100644 (file)
--- a/include/configs/db-88f6820-gp.h
+++ b/include/configs/db-88f6820-gp.h
@@ -10,9 +10,6 @@
 /*
  * High Level Configuration Options (easy to change)
  */
-#define CONFIG_ARMADA_XP               /* SOC Family Name */
-#define CONFIG_ARMADA_38X
-#define CONFIG_DB_88F6820_GP           /* Board target name for DDR training */
 
 #define CONFIG_DISPLAY_BOARDINFO_LATE
 
@@ -28,22 +25,9 @@
  * Commands configuration
  */
 #define CONFIG_SYS_NO_FLASH            /* Declare no flash (NOR/SPI) */
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DHCP
 #define CONFIG_CMD_ENV
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_EXT4
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_FS_GENERIC
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MMC
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SCSI
-#define CONFIG_CMD_SF
-#define CONFIG_CMD_SPI
-#define CONFIG_CMD_TFTPPUT
-#define CONFIG_CMD_TIME
+#define CONFIG_SCSI
 
 /* I2C */
 #define CONFIG_SYS_I2C
@@ -98,13 +82,10 @@
 
 /* PCIe support */
 #ifndef CONFIG_SPL_BUILD
-#define CONFIG_PCI
 #define CONFIG_PCI_MVEBU
-#define CONFIG_PCI_PNP
 #define CONFIG_PCI_SCAN_SHOW
 #endif
 
-#define CONFIG_SYS_CONSOLE_INFO_QUIET  /* don't print console @ startup */
 #define CONFIG_SYS_ALT_MEMTEST
 
 /* Keep device tree and initrd in lower memory so the kernel can access them */
@@ -140,26 +121,15 @@
 #define CONFIG_SPL_STACK               (0x40000000 + ((192 - 16) << 10))
 #define CONFIG_SPL_BOOTROM_SAVE                (CONFIG_SPL_STACK + 4)
 
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_I2C_SUPPORT
-
 #if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH
 /* SPL related SPI defines */
-#define CONFIG_SPL_SPI_SUPPORT
-#define CONFIG_SPL_SPI_FLASH_SUPPORT
 #define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SPL_SPI_BUS             0
-#define CONFIG_SPL_SPI_CS              0
 #define CONFIG_SYS_SPI_U_BOOT_OFFS     0x24000
 #define CONFIG_SYS_U_BOOT_OFFS         CONFIG_SYS_SPI_U_BOOT_OFFS
 #endif
 
 #if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD
 /* SPL related MMC defines */
-#define CONFIG_SPL_MMC_SUPPORT
-#define CONFIG_SPL_LIBDISK_SUPPORT
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION 1
 #define CONFIG_SYS_MMC_U_BOOT_OFFS             (160 << 10)
 #define CONFIG_SYS_U_BOOT_OFFS                 CONFIG_SYS_MMC_U_BOOT_OFFS
@@ -170,10 +140,6 @@
 #endif
 #endif
 
-/* Enable DDR support in SPL (DDR3 training from Marvell bin_hdr) */
-#define CONFIG_SYS_MVEBU_DDR_A38X
-#define CONFIG_DDR3
-
 /*
  * mv-common.h should be defined after CMD configs since it used them
  * to enable certain macros