* USB ConnectTech WhiteHEAT driver
*
* Copyright (C) 2002
- * Connect Tech Inc.
+ * Connect Tech Inc.
*
* Copyright (C) 1999, 2000
* Greg Kroah-Hartman (greg@kroah.com)
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
- * See Documentation/usb/usb-serial.txt for more information on using this driver
+ * See Documentation/usb/usb-serial.txt for more information on using this
+ * driver
*
*/
#define WHITEHEAT_DUMP 7 /* dump memory */
#define WHITEHEAT_STATUS 8 /* get status */
#define WHITEHEAT_PURGE 9 /* clear the UART fifos */
-#define WHITEHEAT_GET_DTR_RTS 10 /* get the state of DTR and RTS for a port */
-#define WHITEHEAT_GET_HW_INFO 11 /* get EEPROM info and hardware ID */
+#define WHITEHEAT_GET_DTR_RTS 10 /* get the state of DTR and RTS
+ for a port */
+#define WHITEHEAT_GET_HW_INFO 11 /* get EEPROM info and
+ hardware ID */
#define WHITEHEAT_REPORT_TX_DONE 12 /* get the next TX done */
#define WHITEHEAT_EVENT 13 /* unsolicited status events */
-#define WHITEHEAT_ECHO 14 /* send data to the indicated IN endpoint */
-#define WHITEHEAT_DO_TEST 15 /* perform the specified test */
-#define WHITEHEAT_CMD_COMPLETE 16 /* reply for certain commands */
+#define WHITEHEAT_ECHO 14 /* send data to the indicated
+ IN endpoint */
+#define WHITEHEAT_DO_TEST 15 /* perform specified test */
+#define WHITEHEAT_CMD_COMPLETE 16 /* reply for some commands */
#define WHITEHEAT_CMD_FAILURE 17 /* reply for failed commands */
#define WHITEHEAT_PAR_MARK '1' /* mark (force 1) parity */
#define WHITEHEAT_SFLOW_NONE 'n' /* no software flow control */
-#define WHITEHEAT_SFLOW_RX 'r' /* XOFF/ON is sent when RX fills/empties */
-#define WHITEHEAT_SFLOW_TX 't' /* when received XOFF/ON will stop/start TX */
+#define WHITEHEAT_SFLOW_RX 'r' /* XOFF/ON is sent when RX
+ fills/empties */
+#define WHITEHEAT_SFLOW_TX 't' /* when received XOFF/ON will
+ stop/start TX */
#define WHITEHEAT_SFLOW_RXTX 'b' /* both SFLOW_RX and SFLOW_TX */
#define WHITEHEAT_HFLOW_NONE 0x00 /* no hardware flow control */
-#define WHITEHEAT_HFLOW_RTS_TOGGLE 0x01 /* RTS is on during transmit, off otherwise */
-#define WHITEHEAT_HFLOW_DTR 0x02 /* DTR is off/on when RX fills/empties */
-#define WHITEHEAT_HFLOW_CTS 0x08 /* when received CTS off/on will stop/start TX */
-#define WHITEHEAT_HFLOW_DSR 0x10 /* when received DSR off/on will stop/start TX */
-#define WHITEHEAT_HFLOW_RTS 0x80 /* RTS is off/on when RX fills/empties */
+#define WHITEHEAT_HFLOW_RTS_TOGGLE 0x01 /* RTS is on during transmit,
+ off otherwise */
+#define WHITEHEAT_HFLOW_DTR 0x02 /* DTR is off/on when RX
+ fills/empties */
+#define WHITEHEAT_HFLOW_CTS 0x08 /* when received CTS off/on
+ will stop/start TX */
+#define WHITEHEAT_HFLOW_DSR 0x10 /* when received DSR off/on
+ will stop/start TX */
+#define WHITEHEAT_HFLOW_RTS 0x80 /* RTS is off/on when RX
+ fills/empties */
struct whiteheat_port_settings {
__u8 port; /* port number (1 to N) */
- __u32 baud; /* any value 7 - 460800, firmware calculates best fit; arrives little endian */
+ __u32 baud; /* any value 7 - 460800, firmware calculates
+ best fit; arrives little endian */
__u8 bits; /* 5, 6, 7, or 8 */
__u8 stop; /* 1 or 2, default 1 (2 = 1.5 if bits = 5) */
__u8 parity; /* see WHITEHEAT_PAR_* above */
*/
#define WHITEHEAT_TEST_UART_RW 0x01 /* read/write uart registers */
#define WHITEHEAT_TEST_UART_INTR 0x02 /* uart interrupt */
-#define WHITEHEAT_TEST_SETUP_CONT 0x03 /* setup for PORT_CONT/PORT_DISCONT */
+#define WHITEHEAT_TEST_SETUP_CONT 0x03 /* setup for
+ PORT_CONT/PORT_DISCONT */
#define WHITEHEAT_TEST_PORT_CONT 0x04 /* port connect */
#define WHITEHEAT_TEST_PORT_DISCONT 0x05 /* port disconnect */
#define WHITEHEAT_TEST_UART_CLK_START 0x06 /* uart clock test start */
#define WHITEHEAT_TEST_UART_CLK_STOP 0x07 /* uart clock test stop */
-#define WHITEHEAT_TEST_MODEM_FT 0x08 /* modem signals, requires a loopback cable/connector */
+#define WHITEHEAT_TEST_MODEM_FT 0x08 /* modem signals, requires a
+ loopback cable/connector */
#define WHITEHEAT_TEST_ERASE_EEPROM 0x09 /* erase eeprom */
#define WHITEHEAT_TEST_READ_EEPROM 0x0a /* read eeprom */
#define WHITEHEAT_TEST_PROGRAM_EEPROM 0x0b /* program eeprom */
#define WHITEHEAT_EVENT_CONNECT 0x08 /* connect field is valid */
#define WHITEHEAT_FLOW_NONE 0x00 /* no flow control active */
-#define WHITEHEAT_FLOW_HARD_OUT 0x01 /* TX is stopped by CTS (waiting for CTS to go on) */
-#define WHITEHEAT_FLOW_HARD_IN 0x02 /* remote TX is stopped by RTS */
-#define WHITEHEAT_FLOW_SOFT_OUT 0x04 /* TX is stopped by XOFF received (waiting for XON) */
-#define WHITEHEAT_FLOW_SOFT_IN 0x08 /* remote TX is stopped by XOFF transmitted */
+#define WHITEHEAT_FLOW_HARD_OUT 0x01 /* TX is stopped by CTS
+ (waiting for CTS to go on) */
+#define WHITEHEAT_FLOW_HARD_IN 0x02 /* remote TX is stopped
+ by RTS */
+#define WHITEHEAT_FLOW_SOFT_OUT 0x04 /* TX is stopped by XOFF
+ received (waiting for XON) */
+#define WHITEHEAT_FLOW_SOFT_IN 0x08 /* remote TX is stopped by XOFF
+ transmitted */
#define WHITEHEAT_FLOW_TX_DONE 0x80 /* TX has completed */
struct whiteheat_status_info {
__u8 port; /* port number (1 to N) */
- __u8 event; /* indicates what the current event is, see WHITEHEAT_EVENT_* above */
- __u8 modem; /* modem signal status (copy of uart's MSR register) */
+ __u8 event; /* indicates what the current event is,
+ see WHITEHEAT_EVENT_* above */
+ __u8 modem; /* modem signal status (copy of uart's
+ MSR register) */
__u8 error; /* line status (copy of uart's LSR register) */
- __u8 flow; /* flow control state, see WHITEHEAT_FLOW_* above */
- __u8 connect; /* 0 means not connected, non-zero means connected */
+ __u8 flow; /* flow control state, see WHITEHEAT_FLOW_*
+ above */
+ __u8 connect; /* 0 means not connected, non-zero means
+ connected */
};
struct whiteheat_event_info {
__u8 port; /* port number (1 to N) */
__u8 event; /* see whiteheat_status_info.event */
- __u8 info; /* see whiteheat_status_info.modem, .error, .flow, .connect */
+ __u8 info; /* see whiteheat_status_info.modem, .error,
+ .flow, .connect */
};
struct whiteheat_test_info {
__u8 port; /* port number (1 to N) */
- __u8 test; /* indicates which test this is a response for, see WHITEHEAT_DO_TEST above */
+ __u8 test; /* indicates which test this is a response for,
+ see WHITEHEAT_DO_TEST above */
__u8 status; /* see WHITEHEAT_TEST_* above */
__u8 results[32]; /* test-dependent results */
};
git.openpandora.org / pandora-kernel.git / blobdiff