#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/slab.h>
+#include <linux/dmi.h>
#include "xhci.h"
* handshake done). There are two failure modes: "usec" have passed (major
* hardware flakeout), or the register reads as all-ones (hardware removed).
*/
-static int handshake(struct xhci_hcd *xhci, void __iomem *ptr,
+int handshake(struct xhci_hcd *xhci, void __iomem *ptr,
u32 mask, u32 done, int usec)
{
u32 result;
ret = handshake(xhci, &xhci->op_regs->status,
STS_HALT, STS_HALT, XHCI_MAX_HALT_USEC);
- if (!ret)
+ if (!ret) {
xhci->xhc_state |= XHCI_STATE_HALTED;
+ xhci->cmd_ring_state = CMD_RING_STATE_STOPPED;
+ } else
+ xhci_warn(xhci, "Host not halted after %u microseconds.\n",
+ XHCI_MAX_HALT_USEC);
return ret;
}
xhci_writel(xhci, command, &xhci->op_regs->command);
ret = handshake(xhci, &xhci->op_regs->command,
- CMD_RESET, 0, 250 * 1000);
+ CMD_RESET, 0, 10 * 1000 * 1000);
if (ret)
return ret;
* xHCI cannot write to any doorbells or operational registers other
* than status until the "Controller Not Ready" flag is cleared.
*/
- return handshake(xhci, &xhci->op_regs->status, STS_CNR, 0, 250 * 1000);
+ return handshake(xhci, &xhci->op_regs->status,
+ STS_CNR, 0, 10 * 1000 * 1000);
}
#ifdef CONFIG_PCI
ret = pci_enable_msi(pdev);
if (ret) {
- xhci_err(xhci, "failed to allocate MSI entry\n");
+ xhci_dbg(xhci, "failed to allocate MSI entry\n");
return ret;
}
ret = request_irq(pdev->irq, (irq_handler_t)xhci_msi_irq,
0, "xhci_hcd", xhci_to_hcd(xhci));
if (ret) {
- xhci_err(xhci, "disable MSI interrupt\n");
+ xhci_dbg(xhci, "disable MSI interrupt\n");
pci_disable_msi(pdev);
}
ret = pci_enable_msix(pdev, xhci->msix_entries, xhci->msix_count);
if (ret) {
- xhci_err(xhci, "Failed to enable MSI-X\n");
+ xhci_dbg(xhci, "Failed to enable MSI-X\n");
goto free_entries;
}
return ret;
disable_msix:
- xhci_err(xhci, "disable MSI-X interrupt\n");
+ xhci_dbg(xhci, "disable MSI-X interrupt\n");
xhci_free_irq(xhci);
pci_disable_msix(pdev);
free_entries:
* generate interrupts. Don't even try to enable MSI.
*/
if (xhci->quirks & XHCI_BROKEN_MSI)
- return 0;
+ goto legacy_irq;
/* unregister the legacy interrupt */
if (hcd->irq)
/* hcd->irq is -1, we have MSI */
return 0;
+ if (!pdev->irq) {
+ xhci_err(xhci, "No msi-x/msi found and no IRQ in BIOS\n");
+ return -EINVAL;
+ }
+
+ legacy_irq:
/* fall back to legacy interrupt*/
ret = request_irq(pdev->irq, &usb_hcd_irq, IRQF_SHARED,
hcd->irq_descr, hcd);
#else
-static int xhci_try_enable_msi(struct usb_hcd *hcd)
+static inline int xhci_try_enable_msi(struct usb_hcd *hcd)
{
return 0;
}
-static void xhci_cleanup_msix(struct xhci_hcd *xhci)
+static inline void xhci_cleanup_msix(struct xhci_hcd *xhci)
{
}
-static void xhci_msix_sync_irqs(struct xhci_hcd *xhci)
+static inline void xhci_msix_sync_irqs(struct xhci_hcd *xhci)
{
}
#endif
+static void compliance_mode_recovery(unsigned long arg)
+{
+ struct xhci_hcd *xhci;
+ struct usb_hcd *hcd;
+ u32 temp;
+ int i;
+
+ xhci = (struct xhci_hcd *)arg;
+
+ for (i = 0; i < xhci->num_usb3_ports; i++) {
+ temp = xhci_readl(xhci, xhci->usb3_ports[i]);
+ if ((temp & PORT_PLS_MASK) == USB_SS_PORT_LS_COMP_MOD) {
+ /*
+ * Compliance Mode Detected. Letting USB Core
+ * handle the Warm Reset
+ */
+ xhci_dbg(xhci, "Compliance Mode Detected->Port %d!\n",
+ i + 1);
+ xhci_dbg(xhci, "Attempting Recovery routine!\n");
+ hcd = xhci->shared_hcd;
+
+ if (hcd->state == HC_STATE_SUSPENDED)
+ usb_hcd_resume_root_hub(hcd);
+
+ usb_hcd_poll_rh_status(hcd);
+ }
+ }
+
+ if (xhci->port_status_u0 != ((1 << xhci->num_usb3_ports)-1))
+ mod_timer(&xhci->comp_mode_recovery_timer,
+ jiffies + msecs_to_jiffies(COMP_MODE_RCVRY_MSECS));
+}
+
+/*
+ * Quirk to work around issue generated by the SN65LVPE502CP USB3.0 re-driver
+ * that causes ports behind that hardware to enter compliance mode sometimes.
+ * The quirk creates a timer that polls every 2 seconds the link state of
+ * each host controller's port and recovers it by issuing a Warm reset
+ * if Compliance mode is detected, otherwise the port will become "dead" (no
+ * device connections or disconnections will be detected anymore). Becasue no
+ * status event is generated when entering compliance mode (per xhci spec),
+ * this quirk is needed on systems that have the failing hardware installed.
+ */
+static void compliance_mode_recovery_timer_init(struct xhci_hcd *xhci)
+{
+ xhci->port_status_u0 = 0;
+ init_timer(&xhci->comp_mode_recovery_timer);
+
+ xhci->comp_mode_recovery_timer.data = (unsigned long) xhci;
+ xhci->comp_mode_recovery_timer.function = compliance_mode_recovery;
+ xhci->comp_mode_recovery_timer.expires = jiffies +
+ msecs_to_jiffies(COMP_MODE_RCVRY_MSECS);
+
+ set_timer_slack(&xhci->comp_mode_recovery_timer,
+ msecs_to_jiffies(COMP_MODE_RCVRY_MSECS));
+ add_timer(&xhci->comp_mode_recovery_timer);
+ xhci_dbg(xhci, "Compliance Mode Recovery Timer Initialized.\n");
+}
+
+/*
+ * This function identifies the systems that have installed the SN65LVPE502CP
+ * USB3.0 re-driver and that need the Compliance Mode Quirk.
+ * Systems:
+ * Vendor: Hewlett-Packard -> System Models: Z420, Z620 and Z820
+ */
+static bool compliance_mode_recovery_timer_quirk_check(void)
+{
+ const char *dmi_product_name, *dmi_sys_vendor;
+
+ dmi_product_name = dmi_get_system_info(DMI_PRODUCT_NAME);
+ dmi_sys_vendor = dmi_get_system_info(DMI_SYS_VENDOR);
+ if (!dmi_product_name || !dmi_sys_vendor)
+ return false;
+
+ if (!(strstr(dmi_sys_vendor, "Hewlett-Packard")))
+ return false;
+
+ if (strstr(dmi_product_name, "Z420") ||
+ strstr(dmi_product_name, "Z620") ||
+ strstr(dmi_product_name, "Z820") ||
+ strstr(dmi_product_name, "Z1 Workstation"))
+ return true;
+
+ return false;
+}
+
+static int xhci_all_ports_seen_u0(struct xhci_hcd *xhci)
+{
+ return (xhci->port_status_u0 == ((1 << xhci->num_usb3_ports)-1));
+}
+
+
/*
* Initialize memory for HCD and xHC (one-time init).
*
retval = xhci_mem_init(xhci, GFP_KERNEL);
xhci_dbg(xhci, "Finished xhci_init\n");
+ /* Initializing Compliance Mode Recovery Data If Needed */
+ if (compliance_mode_recovery_timer_quirk_check()) {
+ xhci->quirks |= XHCI_COMP_MODE_QUIRK;
+ compliance_mode_recovery_timer_init(xhci);
+ }
+
return retval;
}
return -ENODEV;
}
xhci->shared_hcd->state = HC_STATE_RUNNING;
+ xhci->cmd_ring_state = CMD_RING_STATE_RUNNING;
if (xhci->quirks & XHCI_NEC_HOST)
xhci_ring_cmd_db(xhci);
del_timer_sync(&xhci->event_ring_timer);
#endif
+ /* Deleting Compliance Mode Recovery Timer */
+ if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) &&
+ (!(xhci_all_ports_seen_u0(xhci))))
+ del_timer_sync(&xhci->comp_mode_recovery_timer);
+
if (xhci->quirks & XHCI_AMD_PLL_FIX)
usb_amd_dev_put();
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
+ if (xhci->quirks & XHCI_SPURIOUS_REBOOT)
+ usb_disable_xhci_ports(to_pci_dev(hcd->self.controller));
+
spin_lock_irq(&xhci->lock);
xhci_halt(xhci);
+ /* Workaround for spurious wakeups at shutdown with HSW */
+ if (xhci->quirks & XHCI_SPURIOUS_WAKEUP)
+ xhci_reset(xhci);
spin_unlock_irq(&xhci->lock);
xhci_cleanup_msix(xhci);
xhci_dbg(xhci, "xhci_shutdown completed - status = %x\n",
xhci_readl(xhci, &xhci->op_regs->status));
+
+ /* Yet another workaround for spurious wakeups at shutdown with HSW */
+ if (xhci->quirks & XHCI_SPURIOUS_WAKEUP)
+ pci_set_power_state(to_pci_dev(hcd->self.controller), PCI_D3hot);
}
#ifdef CONFIG_PM
xhci->s3.dev_nt = xhci_readl(xhci, &xhci->op_regs->dev_notification);
xhci->s3.dcbaa_ptr = xhci_read_64(xhci, &xhci->op_regs->dcbaa_ptr);
xhci->s3.config_reg = xhci_readl(xhci, &xhci->op_regs->config_reg);
- xhci->s3.irq_pending = xhci_readl(xhci, &xhci->ir_set->irq_pending);
- xhci->s3.irq_control = xhci_readl(xhci, &xhci->ir_set->irq_control);
xhci->s3.erst_size = xhci_readl(xhci, &xhci->ir_set->erst_size);
xhci->s3.erst_base = xhci_read_64(xhci, &xhci->ir_set->erst_base);
xhci->s3.erst_dequeue = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
+ xhci->s3.irq_pending = xhci_readl(xhci, &xhci->ir_set->irq_pending);
+ xhci->s3.irq_control = xhci_readl(xhci, &xhci->ir_set->irq_control);
}
static void xhci_restore_registers(struct xhci_hcd *xhci)
xhci_writel(xhci, xhci->s3.dev_nt, &xhci->op_regs->dev_notification);
xhci_write_64(xhci, xhci->s3.dcbaa_ptr, &xhci->op_regs->dcbaa_ptr);
xhci_writel(xhci, xhci->s3.config_reg, &xhci->op_regs->config_reg);
- xhci_writel(xhci, xhci->s3.irq_pending, &xhci->ir_set->irq_pending);
- xhci_writel(xhci, xhci->s3.irq_control, &xhci->ir_set->irq_control);
xhci_writel(xhci, xhci->s3.erst_size, &xhci->ir_set->erst_size);
xhci_write_64(xhci, xhci->s3.erst_base, &xhci->ir_set->erst_base);
+ xhci_write_64(xhci, xhci->s3.erst_dequeue, &xhci->ir_set->erst_dequeue);
+ xhci_writel(xhci, xhci->s3.irq_pending, &xhci->ir_set->irq_pending);
+ xhci_writel(xhci, xhci->s3.irq_control, &xhci->ir_set->irq_control);
}
static void xhci_set_cmd_ring_deq(struct xhci_hcd *xhci)
int xhci_suspend(struct xhci_hcd *xhci)
{
int rc = 0;
+ unsigned int delay = XHCI_MAX_HALT_USEC;
struct usb_hcd *hcd = xhci_to_hcd(xhci);
u32 command;
+ /* Don't poll the roothubs on bus suspend. */
+ xhci_dbg(xhci, "%s: stopping port polling.\n", __func__);
+ clear_bit(HCD_FLAG_POLL_RH, &hcd->flags);
+ del_timer_sync(&hcd->rh_timer);
+
spin_lock_irq(&xhci->lock);
clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
clear_bit(HCD_FLAG_HW_ACCESSIBLE, &xhci->shared_hcd->flags);
command = xhci_readl(xhci, &xhci->op_regs->command);
command &= ~CMD_RUN;
xhci_writel(xhci, command, &xhci->op_regs->command);
+
+ /* Some chips from Fresco Logic need an extraordinary delay */
+ delay *= (xhci->quirks & XHCI_SLOW_SUSPEND) ? 10 : 1;
+
if (handshake(xhci, &xhci->op_regs->status,
- STS_HALT, STS_HALT, 100*100)) {
+ STS_HALT, STS_HALT, delay)) {
xhci_warn(xhci, "WARN: xHC CMD_RUN timeout\n");
spin_unlock_irq(&xhci->lock);
return -ETIMEDOUT;
command = xhci_readl(xhci, &xhci->op_regs->command);
command |= CMD_CSS;
xhci_writel(xhci, command, &xhci->op_regs->command);
- if (handshake(xhci, &xhci->op_regs->status, STS_SAVE, 0, 10*100)) {
- xhci_warn(xhci, "WARN: xHC CMD_CSS timeout\n");
+ if (handshake(xhci, &xhci->op_regs->status, STS_SAVE, 0, 10 * 1000)) {
+ xhci_warn(xhci, "WARN: xHC save state timeout\n");
spin_unlock_irq(&xhci->lock);
return -ETIMEDOUT;
}
spin_unlock_irq(&xhci->lock);
+ /*
+ * Deleting Compliance Mode Recovery Timer because the xHCI Host
+ * is about to be suspended.
+ */
+ if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) &&
+ (!(xhci_all_ports_seen_u0(xhci)))) {
+ del_timer_sync(&xhci->comp_mode_recovery_timer);
+ xhci_dbg(xhci, "Compliance Mode Recovery Timer Deleted!\n");
+ }
+
/* step 5: remove core well power */
/* synchronize irq when using MSI-X */
xhci_msix_sync_irqs(xhci);
struct usb_hcd *hcd = xhci_to_hcd(xhci);
struct usb_hcd *secondary_hcd;
int retval = 0;
+ bool comp_timer_running = false;
/* Wait a bit if either of the roothubs need to settle from the
* transition into bus suspend.
command |= CMD_CRS;
xhci_writel(xhci, command, &xhci->op_regs->command);
if (handshake(xhci, &xhci->op_regs->status,
- STS_RESTORE, 0, 10*100)) {
- xhci_dbg(xhci, "WARN: xHC CMD_CSS timeout\n");
+ STS_RESTORE, 0, 10 * 1000)) {
+ xhci_warn(xhci, "WARN: xHC restore state timeout\n");
spin_unlock_irq(&xhci->lock);
return -ETIMEDOUT;
}
/* If restore operation fails, re-initialize the HC during resume */
if ((temp & STS_SRE) || hibernated) {
+
+ if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) &&
+ !(xhci_all_ports_seen_u0(xhci))) {
+ del_timer_sync(&xhci->comp_mode_recovery_timer);
+ xhci_dbg(xhci, "Compliance Mode Recovery Timer deleted!\n");
+ }
+
/* Let the USB core know _both_ roothubs lost power. */
usb_root_hub_lost_power(xhci->main_hcd->self.root_hub);
usb_root_hub_lost_power(xhci->shared_hcd->self.root_hub);
retval = xhci_init(hcd->primary_hcd);
if (retval)
return retval;
+ comp_timer_running = true;
+
xhci_dbg(xhci, "Start the primary HCD\n");
retval = xhci_run(hcd->primary_hcd);
if (!retval) {
usb_hcd_resume_root_hub(hcd);
usb_hcd_resume_root_hub(xhci->shared_hcd);
}
+
+ /*
+ * If system is subject to the Quirk, Compliance Mode Timer needs to
+ * be re-initialized Always after a system resume. Ports are subject
+ * to suffer the Compliance Mode issue again. It doesn't matter if
+ * ports have entered previously to U0 before system's suspension.
+ */
+ if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) && !comp_timer_running)
+ compliance_mode_recovery_timer_init(xhci);
+
+ /* Re-enable port polling. */
+ xhci_dbg(xhci, "%s: starting port polling.\n", __func__);
+ set_bit(HCD_FLAG_POLL_RH, &hcd->flags);
+ usb_hcd_poll_rh_status(hcd);
+
return retval;
}
#endif /* CONFIG_PM */
}
xhci = hcd_to_xhci(hcd);
- if (xhci->xhc_state & XHCI_STATE_HALTED)
- return -ENODEV;
-
if (check_virt_dev) {
if (!udev->slot_id || !xhci->devs[udev->slot_id]) {
printk(KERN_DEBUG "xHCI %s called with unaddressed "
}
}
+ if (xhci->xhc_state & XHCI_STATE_HALTED)
+ return -ENODEV;
+
return 1;
}
/* FIXME: can we allocate more resources for the HC? */
break;
case COMP_BW_ERR:
+ case COMP_2ND_BW_ERR:
dev_warn(&udev->dev, "Not enough bandwidth "
"for new device state.\n");
ret = -ENOSPC;
static bool xhci_is_sync_in_ep(unsigned int ep_type)
{
- return (ep_type == ISOC_IN_EP || ep_type != INT_IN_EP);
+ return (ep_type == ISOC_IN_EP || ep_type == INT_IN_EP);
}
static unsigned int xhci_get_ss_bw_consumed(struct xhci_bw_info *ep_bw)
struct completion *cmd_completion;
u32 *cmd_status;
struct xhci_virt_device *virt_dev;
+ union xhci_trb *cmd_trb;
spin_lock_irqsave(&xhci->lock, flags);
virt_dev = xhci->devs[udev->slot_id];
}
init_completion(cmd_completion);
+ cmd_trb = xhci->cmd_ring->dequeue;
if (!ctx_change)
ret = xhci_queue_configure_endpoint(xhci, in_ctx->dma,
udev->slot_id, must_succeed);
/* Wait for the configure endpoint command to complete */
timeleft = wait_for_completion_interruptible_timeout(
cmd_completion,
- USB_CTRL_SET_TIMEOUT);
+ XHCI_CMD_DEFAULT_TIMEOUT);
if (timeleft <= 0) {
xhci_warn(xhci, "%s while waiting for %s command\n",
timeleft == 0 ? "Timeout" : "Signal",
ctx_change == 0 ?
"configure endpoint" :
"evaluate context");
- /* FIXME cancel the configure endpoint command */
+ /* cancel the configure endpoint command */
+ ret = xhci_cancel_cmd(xhci, command, cmd_trb);
+ if (ret < 0)
+ return ret;
return -ETIME;
}
xhci_ring_cmd_db(xhci);
}
virt_ep->stopped_td = NULL;
- virt_ep->stopped_trb = NULL;
virt_ep->stopped_stream = 0;
spin_unlock_irqrestore(&xhci->lock, flags);
if (ret < 0)
return ret;
- max_streams = USB_SS_MAX_STREAMS(
- eps[i]->ss_ep_comp.bmAttributes);
+ max_streams = usb_ss_max_streams(&eps[i]->ss_ep_comp);
if (max_streams < (*num_streams - 1)) {
xhci_dbg(xhci, "Ep 0x%x only supports %u stream IDs.\n",
eps[i]->desc.bEndpointAddress,
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
struct xhci_virt_device *virt_dev;
+ struct device *dev = hcd->self.controller;
unsigned long flags;
u32 state;
int i, ret;
+#ifndef CONFIG_USB_DEFAULT_PERSIST
+ /*
+ * We called pm_runtime_get_noresume when the device was attached.
+ * Decrement the counter here to allow controller to runtime suspend
+ * if no devices remain.
+ */
+ if (xhci->quirks & XHCI_RESET_ON_RESUME)
+ pm_runtime_put_noidle(dev);
+#endif
+
ret = xhci_check_args(hcd, udev, NULL, 0, true, __func__);
/* If the host is halted due to driver unload, we still need to free the
* device.
int xhci_alloc_dev(struct usb_hcd *hcd, struct usb_device *udev)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
+ struct device *dev = hcd->self.controller;
unsigned long flags;
int timeleft;
int ret;
+ union xhci_trb *cmd_trb;
spin_lock_irqsave(&xhci->lock, flags);
+ cmd_trb = xhci->cmd_ring->dequeue;
ret = xhci_queue_slot_control(xhci, TRB_ENABLE_SLOT, 0);
if (ret) {
spin_unlock_irqrestore(&xhci->lock, flags);
/* XXX: how much time for xHC slot assignment? */
timeleft = wait_for_completion_interruptible_timeout(&xhci->addr_dev,
- USB_CTRL_SET_TIMEOUT);
+ XHCI_CMD_DEFAULT_TIMEOUT);
if (timeleft <= 0) {
xhci_warn(xhci, "%s while waiting for a slot\n",
timeleft == 0 ? "Timeout" : "Signal");
- /* FIXME cancel the enable slot request */
- return 0;
+ /* cancel the enable slot request */
+ return xhci_cancel_cmd(xhci, NULL, cmd_trb);
}
if (!xhci->slot_id) {
goto disable_slot;
}
udev->slot_id = xhci->slot_id;
+
+#ifndef CONFIG_USB_DEFAULT_PERSIST
+ /*
+ * If resetting upon resume, we can't put the controller into runtime
+ * suspend if there is a device attached.
+ */
+ if (xhci->quirks & XHCI_RESET_ON_RESUME)
+ pm_runtime_get_noresume(dev);
+#endif
+
/* Is this a LS or FS device under a HS hub? */
/* Hub or peripherial? */
return 1;
struct xhci_slot_ctx *slot_ctx;
struct xhci_input_control_ctx *ctrl_ctx;
u64 temp_64;
+ union xhci_trb *cmd_trb;
if (!udev->slot_id) {
xhci_dbg(xhci, "Bad Slot ID %d\n", udev->slot_id);
xhci_dbg_ctx(xhci, virt_dev->in_ctx, 2);
spin_lock_irqsave(&xhci->lock, flags);
+ cmd_trb = xhci->cmd_ring->dequeue;
ret = xhci_queue_address_device(xhci, virt_dev->in_ctx->dma,
udev->slot_id);
if (ret) {
/* ctrl tx can take up to 5 sec; XXX: need more time for xHC? */
timeleft = wait_for_completion_interruptible_timeout(&xhci->addr_dev,
- USB_CTRL_SET_TIMEOUT);
+ XHCI_CMD_DEFAULT_TIMEOUT);
/* FIXME: From section 4.3.4: "Software shall be responsible for timing
* the SetAddress() "recovery interval" required by USB and aborting the
* command on a timeout.
if (timeleft <= 0) {
xhci_warn(xhci, "%s while waiting for address device command\n",
timeleft == 0 ? "Timeout" : "Signal");
- /* FIXME cancel the address device command */
+ /* cancel the address device command */
+ ret = xhci_cancel_cmd(xhci, NULL, cmd_trb);
+ if (ret < 0)
+ return ret;
return -ETIME;
}
get_quirks(dev, xhci);
+ /* In xhci controllers which follow xhci 1.0 spec gives a spurious
+ * success event after a short transfer. This quirk will ignore such
+ * spurious event.
+ */
+ if (xhci->hci_version > 0x96)
+ xhci->quirks |= XHCI_SPURIOUS_SUCCESS;
+
/* Make sure the HC is halted. */
retval = xhci_halt(xhci);
if (retval)