int port;
int mask;
+ ehci_dbg(ehci, "suspend root hub\n");
+
if (time_before (jiffies, ehci->next_statechange))
msleep(5);
ehci_quiesce (ehci);
hcd->state = HC_STATE_QUIESCING;
}
- ehci->command = readl (&ehci->regs->command);
+ ehci->command = ehci_readl(ehci, &ehci->regs->command);
if (ehci->reclaim)
ehci->reclaim_ready = 1;
ehci_work(ehci);
ehci->bus_suspended = 0;
while (port--) {
u32 __iomem *reg = &ehci->regs->port_status [port];
- u32 t1 = readl (reg) & ~PORT_RWC_BITS;
+ u32 t1 = ehci_readl(ehci, reg) & ~PORT_RWC_BITS;
u32 t2 = t1;
/* keep track of which ports we suspend */
if (t1 != t2) {
ehci_vdbg (ehci, "port %d, %08x -> %08x\n",
port + 1, t1, t2);
- writel (t2, reg);
+ ehci_writel(ehci, t2, reg);
}
}
mask = INTR_MASK;
if (!device_may_wakeup(&hcd->self.root_hub->dev))
mask &= ~STS_PCD;
- writel(mask, &ehci->regs->intr_enable);
- readl(&ehci->regs->intr_enable);
+ ehci_writel(ehci, mask, &ehci->regs->intr_enable);
+ ehci_readl(ehci, &ehci->regs->intr_enable);
ehci->next_statechange = jiffies + msecs_to_jiffies(10);
spin_unlock_irq (&ehci->lock);
* the last user of the controller, not reset/pm hardware keeping
* state we gave to it.
*/
- temp = readl(&ehci->regs->intr_enable);
+ temp = ehci_readl(ehci, &ehci->regs->intr_enable);
ehci_dbg(ehci, "resume root hub%s\n", temp ? "" : " after power loss");
/* at least some APM implementations will try to deliver
* IRQs right away, so delay them until we're ready.
*/
- writel(0, &ehci->regs->intr_enable);
+ ehci_writel(ehci, 0, &ehci->regs->intr_enable);
/* re-init operational registers */
- writel(0, &ehci->regs->segment);
- writel(ehci->periodic_dma, &ehci->regs->frame_list);
- writel((u32) ehci->async->qh_dma, &ehci->regs->async_next);
+ ehci_writel(ehci, 0, &ehci->regs->segment);
+ ehci_writel(ehci, ehci->periodic_dma, &ehci->regs->frame_list);
+ ehci_writel(ehci, (u32) ehci->async->qh_dma, &ehci->regs->async_next);
/* restore CMD_RUN, framelist size, and irq threshold */
- writel (ehci->command, &ehci->regs->command);
+ ehci_writel(ehci, ehci->command, &ehci->regs->command);
+
+ /* Some controller/firmware combinations need a delay during which
+ * they set up the port statuses. See Bugzilla #8190. */
+ mdelay(8);
/* manually resume the ports we suspended during bus_suspend() */
i = HCS_N_PORTS (ehci->hcs_params);
while (i--) {
- temp = readl (&ehci->regs->port_status [i]);
+ temp = ehci_readl(ehci, &ehci->regs->port_status [i]);
temp &= ~(PORT_RWC_BITS
| PORT_WKOC_E | PORT_WKDISC_E | PORT_WKCONN_E);
if (test_bit(i, &ehci->bus_suspended) &&
ehci->reset_done [i] = jiffies + msecs_to_jiffies (20);
temp |= PORT_RESUME;
}
- writel (temp, &ehci->regs->port_status [i]);
+ ehci_writel(ehci, temp, &ehci->regs->port_status [i]);
}
i = HCS_N_PORTS (ehci->hcs_params);
mdelay (20);
while (i--) {
- temp = readl (&ehci->regs->port_status [i]);
+ temp = ehci_readl(ehci, &ehci->regs->port_status [i]);
if (test_bit(i, &ehci->bus_suspended) &&
(temp & PORT_SUSPEND)) {
temp &= ~(PORT_RWC_BITS | PORT_RESUME);
- writel (temp, &ehci->regs->port_status [i]);
+ ehci_writel(ehci, temp, &ehci->regs->port_status [i]);
ehci_vdbg (ehci, "resumed port %d\n", i + 1);
}
}
- (void) readl (&ehci->regs->command);
+ (void) ehci_readl(ehci, &ehci->regs->command);
/* maybe re-activate the schedule(s) */
temp = 0;
temp |= CMD_PSE;
if (temp) {
ehci->command |= temp;
- writel (ehci->command, &ehci->regs->command);
+ ehci_writel(ehci, ehci->command, &ehci->regs->command);
}
ehci->next_statechange = jiffies + msecs_to_jiffies(5);
hcd->state = HC_STATE_RUNNING;
/* Now we can safely re-enable irqs */
- writel(INTR_MASK, &ehci->regs->intr_enable);
+ ehci_writel(ehci, INTR_MASK, &ehci->regs->intr_enable);
spin_unlock_irq (&ehci->lock);
return 0;
#endif /* CONFIG_PM */
+/*-------------------------------------------------------------------------*/
+
+/* Display the ports dedicated to the companion controller */
+static ssize_t show_companion(struct class_device *class_dev, char *buf)
+{
+ struct ehci_hcd *ehci;
+ int nports, index, n;
+ int count = PAGE_SIZE;
+ char *ptr = buf;
+
+ ehci = hcd_to_ehci(bus_to_hcd(class_get_devdata(class_dev)));
+ nports = HCS_N_PORTS(ehci->hcs_params);
+
+ for (index = 0; index < nports; ++index) {
+ if (test_bit(index, &ehci->companion_ports)) {
+ n = scnprintf(ptr, count, "%d\n", index + 1);
+ ptr += n;
+ count -= n;
+ }
+ }
+ return ptr - buf;
+}
+
+/*
+ * Dedicate or undedicate a port to the companion controller.
+ * Syntax is "[-]portnum", where a leading '-' sign means
+ * return control of the port to the EHCI controller.
+ */
+static ssize_t store_companion(struct class_device *class_dev,
+ const char *buf, size_t count)
+{
+ struct ehci_hcd *ehci;
+ int portnum, new_owner, try;
+ u32 __iomem *status_reg;
+ u32 port_status;
+
+ ehci = hcd_to_ehci(bus_to_hcd(class_get_devdata(class_dev)));
+ new_owner = PORT_OWNER; /* Owned by companion */
+ if (sscanf(buf, "%d", &portnum) != 1)
+ return -EINVAL;
+ if (portnum < 0) {
+ portnum = - portnum;
+ new_owner = 0; /* Owned by EHCI */
+ }
+ if (portnum <= 0 || portnum > HCS_N_PORTS(ehci->hcs_params))
+ return -ENOENT;
+ status_reg = &ehci->regs->port_status[--portnum];
+ if (new_owner)
+ set_bit(portnum, &ehci->companion_ports);
+ else
+ clear_bit(portnum, &ehci->companion_ports);
+
+ /*
+ * The controller won't set the OWNER bit if the port is
+ * enabled, so this loop will sometimes require at least two
+ * iterations: one to disable the port and one to set OWNER.
+ */
+
+ for (try = 4; try > 0; --try) {
+ spin_lock_irq(&ehci->lock);
+ port_status = ehci_readl(ehci, status_reg);
+ if ((port_status & PORT_OWNER) == new_owner
+ || (port_status & (PORT_OWNER | PORT_CONNECT))
+ == 0)
+ try = 0;
+ else {
+ port_status ^= PORT_OWNER;
+ port_status &= ~(PORT_PE | PORT_RWC_BITS);
+ ehci_writel(ehci, port_status, status_reg);
+ }
+ spin_unlock_irq(&ehci->lock);
+ if (try > 1)
+ msleep(5);
+ }
+ return count;
+}
+static CLASS_DEVICE_ATTR(companion, 0644, show_companion, store_companion);
+
+static inline void create_companion_file(struct ehci_hcd *ehci)
+{
+ int i;
+
+ /* with integrated TT there is no companion! */
+ if (!ehci_is_TDI(ehci))
+ i = class_device_create_file(ehci_to_hcd(ehci)->self.class_dev,
+ &class_device_attr_companion);
+}
+
+static inline void remove_companion_file(struct ehci_hcd *ehci)
+{
+ /* with integrated TT there is no companion! */
+ if (!ehci_is_TDI(ehci))
+ class_device_remove_file(ehci_to_hcd(ehci)->self.class_dev,
+ &class_device_attr_companion);
+}
+
+
/*-------------------------------------------------------------------------*/
static int check_reset_complete (
struct ehci_hcd *ehci,
int index,
+ u32 __iomem *status_reg,
int port_status
) {
if (!(port_status & PORT_CONNECT)) {
// what happens if HCS_N_CC(params) == 0 ?
port_status |= PORT_OWNER;
port_status &= ~PORT_RWC_BITS;
- writel (port_status, &ehci->regs->port_status [index]);
+ ehci_writel(ehci, port_status, status_reg);
} else
ehci_dbg (ehci, "port %d high speed\n", index + 1);
/* port N changes (bit N)? */
spin_lock_irqsave (&ehci->lock, flags);
for (i = 0; i < ports; i++) {
- temp = readl (&ehci->regs->port_status [i]);
- if (temp & PORT_OWNER) {
- /* don't report this in GetPortStatus */
- if (temp & PORT_CSC) {
- temp &= ~PORT_RWC_BITS;
- temp |= PORT_CSC;
- writel (temp, &ehci->regs->port_status [i]);
- }
- continue;
- }
+ temp = ehci_readl(ehci, &ehci->regs->port_status [i]);
+
+ /*
+ * Return status information even for ports with OWNER set.
+ * Otherwise khubd wouldn't see the disconnect event when a
+ * high-speed device is switched over to the companion
+ * controller by the user.
+ */
+
if (!(temp & PORT_CONNECT))
ehci->reset_done [i] = 0;
if ((temp & mask) != 0
|| ((temp & PORT_RESUME) != 0
- && time_after (jiffies,
- ehci->reset_done [i]))) {
+ && time_after_eq(jiffies,
+ ehci->reset_done[i]))) {
if (i < 7)
buf [0] |= 1 << (i + 1);
else
) {
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
int ports = HCS_N_PORTS (ehci->hcs_params);
+ u32 __iomem *status_reg = &ehci->regs->port_status[wIndex - 1];
u32 temp, status;
unsigned long flags;
int retval = 0;
if (!wIndex || wIndex > ports)
goto error;
wIndex--;
- temp = readl (&ehci->regs->port_status [wIndex]);
- if (temp & PORT_OWNER)
- break;
+ temp = ehci_readl(ehci, status_reg);
+
+ /*
+ * Even if OWNER is set, so the port is owned by the
+ * companion controller, khubd needs to be able to clear
+ * the port-change status bits (especially
+ * USB_PORT_FEAT_C_CONNECTION).
+ */
switch (wValue) {
case USB_PORT_FEAT_ENABLE:
- writel (temp & ~PORT_PE,
- &ehci->regs->port_status [wIndex]);
+ ehci_writel(ehci, temp & ~PORT_PE, status_reg);
break;
case USB_PORT_FEAT_C_ENABLE:
- writel((temp & ~PORT_RWC_BITS) | PORT_PEC,
- &ehci->regs->port_status [wIndex]);
+ ehci_writel(ehci, (temp & ~PORT_RWC_BITS) | PORT_PEC,
+ status_reg);
break;
case USB_PORT_FEAT_SUSPEND:
if (temp & PORT_RESET)
goto error;
/* resume signaling for 20 msec */
temp &= ~(PORT_RWC_BITS | PORT_WAKE_BITS);
- writel (temp | PORT_RESUME,
- &ehci->regs->port_status [wIndex]);
+ ehci_writel(ehci, temp | PORT_RESUME,
+ status_reg);
ehci->reset_done [wIndex] = jiffies
+ msecs_to_jiffies (20);
}
break;
case USB_PORT_FEAT_POWER:
if (HCS_PPC (ehci->hcs_params))
- writel (temp & ~(PORT_RWC_BITS | PORT_POWER),
- &ehci->regs->port_status [wIndex]);
+ ehci_writel(ehci,
+ temp & ~(PORT_RWC_BITS | PORT_POWER),
+ status_reg);
break;
case USB_PORT_FEAT_C_CONNECTION:
- writel((temp & ~PORT_RWC_BITS) | PORT_CSC,
- &ehci->regs->port_status [wIndex]);
+ ehci_writel(ehci, (temp & ~PORT_RWC_BITS) | PORT_CSC,
+ status_reg);
break;
case USB_PORT_FEAT_C_OVER_CURRENT:
- writel((temp & ~PORT_RWC_BITS) | PORT_OCC,
- &ehci->regs->port_status [wIndex]);
+ ehci_writel(ehci, (temp & ~PORT_RWC_BITS) | PORT_OCC,
+ status_reg);
break;
case USB_PORT_FEAT_C_RESET:
/* GetPortStatus clears reset */
default:
goto error;
}
- readl (&ehci->regs->command); /* unblock posted write */
+ ehci_readl(ehci, &ehci->regs->command); /* unblock posted write */
break;
case GetHubDescriptor:
ehci_hub_descriptor (ehci, (struct usb_hub_descriptor *)
goto error;
wIndex--;
status = 0;
- temp = readl (&ehci->regs->port_status [wIndex]);
+ temp = ehci_readl(ehci, status_reg);
// wPortChange bits
if (temp & PORT_CSC)
status |= 1 << USB_PORT_FEAT_C_OVER_CURRENT;
/* whoever resumes must GetPortStatus to complete it!! */
- if ((temp & PORT_RESUME)
- && time_after (jiffies,
- ehci->reset_done [wIndex])) {
- status |= 1 << USB_PORT_FEAT_C_SUSPEND;
- ehci->reset_done [wIndex] = 0;
+ if (temp & PORT_RESUME) {
- /* stop resume signaling */
- temp = readl (&ehci->regs->port_status [wIndex]);
- writel (temp & ~(PORT_RWC_BITS | PORT_RESUME),
- &ehci->regs->port_status [wIndex]);
- retval = handshake (
- &ehci->regs->port_status [wIndex],
- PORT_RESUME, 0, 2000 /* 2msec */);
- if (retval != 0) {
- ehci_err (ehci, "port %d resume error %d\n",
- wIndex + 1, retval);
- goto error;
+ /* Remote Wakeup received? */
+ if (!ehci->reset_done[wIndex]) {
+ /* resume signaling for 20 msec */
+ ehci->reset_done[wIndex] = jiffies
+ + msecs_to_jiffies(20);
+ /* check the port again */
+ mod_timer(&ehci_to_hcd(ehci)->rh_timer,
+ ehci->reset_done[wIndex]);
+ }
+
+ /* resume completed? */
+ else if (time_after_eq(jiffies,
+ ehci->reset_done[wIndex])) {
+ status |= 1 << USB_PORT_FEAT_C_SUSPEND;
+ ehci->reset_done[wIndex] = 0;
+
+ /* stop resume signaling */
+ temp = ehci_readl(ehci, status_reg);
+ ehci_writel(ehci,
+ temp & ~(PORT_RWC_BITS | PORT_RESUME),
+ status_reg);
+ retval = handshake(ehci, status_reg,
+ PORT_RESUME, 0, 2000 /* 2msec */);
+ if (retval != 0) {
+ ehci_err(ehci,
+ "port %d resume error %d\n",
+ wIndex + 1, retval);
+ goto error;
+ }
+ temp &= ~(PORT_SUSPEND|PORT_RESUME|(3<<10));
}
- temp &= ~(PORT_SUSPEND|PORT_RESUME|(3<<10));
}
/* whoever resets must GetPortStatus to complete it!! */
if ((temp & PORT_RESET)
- && time_after (jiffies,
- ehci->reset_done [wIndex])) {
+ && time_after_eq(jiffies,
+ ehci->reset_done[wIndex])) {
status |= 1 << USB_PORT_FEAT_C_RESET;
ehci->reset_done [wIndex] = 0;
/* force reset to complete */
- writel (temp & ~(PORT_RWC_BITS | PORT_RESET),
- &ehci->regs->port_status [wIndex]);
+ ehci_writel(ehci, temp & ~(PORT_RWC_BITS | PORT_RESET),
+ status_reg);
/* REVISIT: some hardware needs 550+ usec to clear
* this bit; seems too long to spin routinely...
*/
- retval = handshake (
- &ehci->regs->port_status [wIndex],
+ retval = handshake(ehci, status_reg,
PORT_RESET, 0, 750);
if (retval != 0) {
ehci_err (ehci, "port %d reset error %d\n",
}
/* see what we found out */
- temp = check_reset_complete (ehci, wIndex,
- readl (&ehci->regs->port_status [wIndex]));
+ temp = check_reset_complete (ehci, wIndex, status_reg,
+ ehci_readl(ehci, status_reg));
}
- // don't show wPortStatus if it's owned by a companion hc
- if (!(temp & PORT_OWNER)) {
- if (temp & PORT_CONNECT) {
- status |= 1 << USB_PORT_FEAT_CONNECTION;
- // status may be from integrated TT
- status |= ehci_port_speed(ehci, temp);
- }
- if (temp & PORT_PE)
- status |= 1 << USB_PORT_FEAT_ENABLE;
- if (temp & (PORT_SUSPEND|PORT_RESUME))
- status |= 1 << USB_PORT_FEAT_SUSPEND;
- if (temp & PORT_OC)
- status |= 1 << USB_PORT_FEAT_OVER_CURRENT;
- if (temp & PORT_RESET)
- status |= 1 << USB_PORT_FEAT_RESET;
- if (temp & PORT_POWER)
- status |= 1 << USB_PORT_FEAT_POWER;
+ /* transfer dedicated ports to the companion hc */
+ if ((temp & PORT_CONNECT) &&
+ test_bit(wIndex, &ehci->companion_ports)) {
+ temp &= ~PORT_RWC_BITS;
+ temp |= PORT_OWNER;
+ ehci_writel(ehci, temp, status_reg);
+ ehci_dbg(ehci, "port %d --> companion\n", wIndex + 1);
+ temp = ehci_readl(ehci, status_reg);
+ }
+
+ /*
+ * Even if OWNER is set, there's no harm letting khubd
+ * see the wPortStatus values (they should all be 0 except
+ * for PORT_POWER anyway).
+ */
+
+ if (temp & PORT_CONNECT) {
+ status |= 1 << USB_PORT_FEAT_CONNECTION;
+ // status may be from integrated TT
+ status |= ehci_port_speed(ehci, temp);
}
+ if (temp & PORT_PE)
+ status |= 1 << USB_PORT_FEAT_ENABLE;
+ if (temp & (PORT_SUSPEND|PORT_RESUME))
+ status |= 1 << USB_PORT_FEAT_SUSPEND;
+ if (temp & PORT_OC)
+ status |= 1 << USB_PORT_FEAT_OVER_CURRENT;
+ if (temp & PORT_RESET)
+ status |= 1 << USB_PORT_FEAT_RESET;
+ if (temp & PORT_POWER)
+ status |= 1 << USB_PORT_FEAT_POWER;
#ifndef EHCI_VERBOSE_DEBUG
if (status & ~0xffff) /* only if wPortChange is interesting */
#endif
dbg_port (ehci, "GetStatus", wIndex + 1, temp);
- // we "know" this alignment is good, caller used kmalloc()...
- *((__le32 *) buf) = cpu_to_le32 (status);
+ put_unaligned(cpu_to_le32 (status), (__le32 *) buf);
break;
case SetHubFeature:
switch (wValue) {
if (!wIndex || wIndex > ports)
goto error;
wIndex--;
- temp = readl (&ehci->regs->port_status [wIndex]);
+ temp = ehci_readl(ehci, status_reg);
if (temp & PORT_OWNER)
break;
goto error;
if (device_may_wakeup(&hcd->self.root_hub->dev))
temp |= PORT_WAKE_BITS;
- writel (temp | PORT_SUSPEND,
- &ehci->regs->port_status [wIndex]);
+ ehci_writel(ehci, temp | PORT_SUSPEND, status_reg);
break;
case USB_PORT_FEAT_POWER:
if (HCS_PPC (ehci->hcs_params))
- writel (temp | PORT_POWER,
- &ehci->regs->port_status [wIndex]);
+ ehci_writel(ehci, temp | PORT_POWER,
+ status_reg);
break;
case USB_PORT_FEAT_RESET:
if (temp & PORT_RESUME)
ehci->reset_done [wIndex] = jiffies
+ msecs_to_jiffies (50);
}
- writel (temp, &ehci->regs->port_status [wIndex]);
+ ehci_writel(ehci, temp, status_reg);
break;
/* For downstream facing ports (these): one hub port is put
ehci_quiesce(ehci);
ehci_halt(ehci);
temp |= selector << 16;
- writel (temp, &ehci->regs->port_status [wIndex]);
+ ehci_writel(ehci, temp, status_reg);
break;
default:
goto error;
}
- readl (&ehci->regs->command); /* unblock posted writes */
+ ehci_readl(ehci, &ehci->regs->command); /* unblock posted writes */
break;
default:
git.openpandora.org / pandora-kernel.git / blobdiff