#include <linux/printk.h>
#include <linux/pci_ids.h>
#include <linux/netdevice.h>
+#include <linux/interrupt.h>
#include <linux/sched.h>
#include <linux/mmc/sdio.h>
#include <linux/mmc/sdio_func.h>
#include <brcm_hw_ids.h>
#include <soc.h>
#include "sdio_host.h"
-#include "bcmsdbus.h"
/* register access macros */
#ifndef __BIG_ENDIAN
#endif /* BCMDBG */
#include <chipcommon.h>
-#include "sbsdio.h"
-
-#include "dngl_stats.h"
#include "dhd.h"
#include "dhd_bus.h"
#include "dhd_proto.h"
#ifndef BRCMF_FIRSTREAD
#define BRCMF_FIRSTREAD 32
#endif
+
#if !ISPOWEROF2(BRCMF_FIRSTREAD)
#error BRCMF_FIRSTREAD is not a power of 2!
#endif
+/* SBSDIO_DEVICE_CTL */
+#define SBSDIO_DEVCTL_SETBUSY 0x01 /* 1: device will assert busy signal when
+ * receiving CMD53
+ */
+#define SBSDIO_DEVCTL_SPI_INTR_SYNC 0x02 /* 1: assertion of sdio interrupt is
+ * synchronous to the sdio clock
+ */
+#define SBSDIO_DEVCTL_CA_INT_ONLY 0x04 /* 1: mask all interrupts to host
+ * except the chipActive (rev 8)
+ */
+#define SBSDIO_DEVCTL_PADS_ISO 0x08 /* 1: isolate internal sdio signals, put
+ * external pads in tri-state; requires
+ * sdio bus power cycle to clear (rev 9)
+ */
+#define SBSDIO_DEVCTL_SB_RST_CTL 0x30 /* Force SD->SB reset mapping (rev 11) */
+#define SBSDIO_DEVCTL_RST_CORECTL 0x00 /* Determined by CoreControl bit */
+#define SBSDIO_DEVCTL_RST_BPRESET 0x10 /* Force backplane reset */
+#define SBSDIO_DEVCTL_RST_NOBPRESET 0x20 /* Force no backplane reset */
+
+/* SBSDIO_FUNC1_CHIPCLKCSR */
+#define SBSDIO_FORCE_ALP 0x01 /* Force ALP request to backplane */
+#define SBSDIO_FORCE_HT 0x02 /* Force HT request to backplane */
+#define SBSDIO_FORCE_ILP 0x04 /* Force ILP request to backplane */
+#define SBSDIO_ALP_AVAIL_REQ 0x08 /* Make ALP ready (power up xtal) */
+#define SBSDIO_HT_AVAIL_REQ 0x10 /* Make HT ready (power up PLL) */
+#define SBSDIO_FORCE_HW_CLKREQ_OFF 0x20 /* Squelch clock requests from HW */
+#define SBSDIO_ALP_AVAIL 0x40 /* Status: ALP is ready */
+#define SBSDIO_HT_AVAIL 0x80 /* Status: HT is ready */
+
+#define SBSDIO_AVBITS (SBSDIO_HT_AVAIL | SBSDIO_ALP_AVAIL)
+#define SBSDIO_ALPAV(regval) ((regval) & SBSDIO_AVBITS)
+#define SBSDIO_HTAV(regval) (((regval) & SBSDIO_AVBITS) == SBSDIO_AVBITS)
+#define SBSDIO_ALPONLY(regval) (SBSDIO_ALPAV(regval) && !SBSDIO_HTAV(regval))
+#define SBSDIO_CLKAV(regval, alponly) (SBSDIO_ALPAV(regval) && \
+ (alponly ? 1 : SBSDIO_HTAV(regval)))
+/* direct(mapped) cis space */
+#define SBSDIO_CIS_BASE_COMMON 0x1000 /* MAPPED common CIS address */
+#define SBSDIO_CIS_SIZE_LIMIT 0x200 /* maximum bytes in one CIS */
+#define SBSDIO_CIS_OFT_ADDR_MASK 0x1FFFF /* cis offset addr is < 17 bits */
+
+#define SBSDIO_CIS_MANFID_TUPLE_LEN 6 /* manfid tuple length, include tuple,
+ * link bytes
+ */
+
+/* intstatus */
+#define I_SMB_SW0 (1 << 0) /* To SB Mail S/W interrupt 0 */
+#define I_SMB_SW1 (1 << 1) /* To SB Mail S/W interrupt 1 */
+#define I_SMB_SW2 (1 << 2) /* To SB Mail S/W interrupt 2 */
+#define I_SMB_SW3 (1 << 3) /* To SB Mail S/W interrupt 3 */
+#define I_SMB_SW_MASK 0x0000000f /* To SB Mail S/W interrupts mask */
+#define I_SMB_SW_SHIFT 0 /* To SB Mail S/W interrupts shift */
+#define I_HMB_SW0 (1 << 4) /* To Host Mail S/W interrupt 0 */
+#define I_HMB_SW1 (1 << 5) /* To Host Mail S/W interrupt 1 */
+#define I_HMB_SW2 (1 << 6) /* To Host Mail S/W interrupt 2 */
+#define I_HMB_SW3 (1 << 7) /* To Host Mail S/W interrupt 3 */
+#define I_HMB_SW_MASK 0x000000f0 /* To Host Mail S/W interrupts mask */
+#define I_HMB_SW_SHIFT 4 /* To Host Mail S/W interrupts shift */
+#define I_WR_OOSYNC (1 << 8) /* Write Frame Out Of Sync */
+#define I_RD_OOSYNC (1 << 9) /* Read Frame Out Of Sync */
+#define I_PC (1 << 10) /* descriptor error */
+#define I_PD (1 << 11) /* data error */
+#define I_DE (1 << 12) /* Descriptor protocol Error */
+#define I_RU (1 << 13) /* Receive descriptor Underflow */
+#define I_RO (1 << 14) /* Receive fifo Overflow */
+#define I_XU (1 << 15) /* Transmit fifo Underflow */
+#define I_RI (1 << 16) /* Receive Interrupt */
+#define I_BUSPWR (1 << 17) /* SDIO Bus Power Change (rev 9) */
+#define I_XMTDATA_AVAIL (1 << 23) /* bits in fifo */
+#define I_XI (1 << 24) /* Transmit Interrupt */
+#define I_RF_TERM (1 << 25) /* Read Frame Terminate */
+#define I_WF_TERM (1 << 26) /* Write Frame Terminate */
+#define I_PCMCIA_XU (1 << 27) /* PCMCIA Transmit FIFO Underflow */
+#define I_SBINT (1 << 28) /* sbintstatus Interrupt */
+#define I_CHIPACTIVE (1 << 29) /* chip from doze to active state */
+#define I_SRESET (1 << 30) /* CCCR RES interrupt */
+#define I_IOE2 (1U << 31) /* CCCR IOE2 Bit Changed */
+#define I_ERRORS (I_PC | I_PD | I_DE | I_RU | I_RO | I_XU)
+#define I_DMA (I_RI | I_XI | I_ERRORS)
+
+/* corecontrol */
+#define CC_CISRDY (1 << 0) /* CIS Ready */
+#define CC_BPRESEN (1 << 1) /* CCCR RES signal */
+#define CC_F2RDY (1 << 2) /* set CCCR IOR2 bit */
+#define CC_CLRPADSISO (1 << 3) /* clear SDIO pads isolation */
+#define CC_XMTDATAAVAIL_MODE (1 << 4)
+#define CC_XMTDATAAVAIL_CTRL (1 << 5)
+
+/* SDA_FRAMECTRL */
+#define SFC_RF_TERM (1 << 0) /* Read Frame Terminate */
+#define SFC_WF_TERM (1 << 1) /* Write Frame Terminate */
+#define SFC_CRC4WOOS (1 << 2) /* CRC error for write out of sync */
+#define SFC_ABORTALL (1 << 3) /* Abort all in-progress frames */
+
+/* HW frame tag */
+#define SDPCM_FRAMETAG_LEN 4 /* 2 bytes len, 2 bytes check val */
+
/* Total length of frame header for dongle protocol */
#define SDPCM_HDRLEN (SDPCM_FRAMETAG_LEN + SDPCM_SWHEADER_LEN)
#ifdef SDTEST
git.openpandora.org / pandora-kernel.git / blobdiff