config SCSI_ADVANSYS
tristate "AdvanSys SCSI support"
- depends on (ISA || EISA || PCI) && SCSI && BROKEN
+ depends on SCSI
+ depends on ISA || EISA || PCI
+ depends on BROKEN || X86_32
help
This is a driver for all SCSI host adapters manufactured by
AdvanSys. It is documented in the kernel source in
If unsure, say N.
+config SCSI_HPTIOP
+ tristate "HighPoint RocketRAID 3xxx Controller support"
+ depends on SCSI && PCI
+ help
+ This option enables support for HighPoint RocketRAID 3xxx
+ controllers.
+
+ To compile this driver as a module, choose M here; the module
+ will be called hptiop. If unsure, say N.
+
config SCSI_SATA_QSTOR
tristate "Pacific Digital SATA QStor support"
depends on SCSI_SATA && PCI
memory using PCI DAC cycles.
config SCSI_SYM53C8XX_DEFAULT_TAGS
- int "default tagged command queue depth"
+ int "Default tagged command queue depth"
depends on SCSI_SYM53C8XX_2
default "16"
help
exceed CONFIG_SCSI_SYM53C8XX_MAX_TAGS.
config SCSI_SYM53C8XX_MAX_TAGS
- int "maximum number of queued commands"
+ int "Maximum number of queued commands"
depends on SCSI_SYM53C8XX_2
default "64"
help
possible. The driver supports up to 256 queued commands per device.
This value is used as a compiled-in hard limit.
-config SCSI_SYM53C8XX_IOMAPPED
- bool "use port IO"
+config SCSI_SYM53C8XX_MMIO
+ bool "Use memory mapped IO"
depends on SCSI_SYM53C8XX_2
+ default y
help
- If you say Y here, the driver will use port IO to access
- the card. This is significantly slower then using memory
- mapped IO. Most people should answer N.
+ Memory mapped IO is faster than Port IO. Most people should
+ answer Y here, but some machines may have problems. If you have
+ to answer N here, please report the problem to the maintainer.
config SCSI_IPR
tristate "IBM Power Linux RAID adapter support"
you do not have this SCSI card, so say N.
config SCSI_NCR53C8XX_DEFAULT_TAGS
- int " default tagged command queue depth"
+ int "default tagged command queue depth"
depends on SCSI_ZALON || SCSI_NCR_Q720
default "8"
---help---
There is no safe option other than using good SCSI devices.
config SCSI_NCR53C8XX_MAX_TAGS
- int " maximum number of queued commands"
+ int "maximum number of queued commands"
depends on SCSI_ZALON || SCSI_NCR_Q720
default "32"
---help---
There is no safe option and the default answer is recommended.
config SCSI_NCR53C8XX_SYNC
- int " synchronous transfers frequency in MHz"
+ int "synchronous transfers frequency in MHz"
depends on SCSI_ZALON || SCSI_NCR_Q720
default "20"
---help---
terminations and SCSI conformant devices.
config SCSI_NCR53C8XX_PROFILE
- bool " enable profiling"
+ bool "enable profiling"
depends on SCSI_ZALON || SCSI_NCR_Q720
help
This option allows you to enable profiling information gathering.
The normal answer therefore is N.
config SCSI_NCR53C8XX_NO_DISCONNECT
- bool " not allow targets to disconnect"
+ bool "not allow targets to disconnect"
depends on (SCSI_ZALON || SCSI_NCR_Q720) && SCSI_NCR53C8XX_DEFAULT_TAGS=0
help
This option is only provided for safety if you suspect some SCSI
To compile this driver as a module, choose M here: the
module will be called qlogicfas.
-config SCSI_QLOGIC_FC
- tristate "Qlogic ISP FC SCSI support"
- depends on PCI && SCSI
- help
- This is a driver for the QLogic ISP2100 SCSI-FCP host adapter.
-
- To compile this driver as a module, choose M here: the
- module will be called qlogicfc.
-
config SCSI_QLOGIC_FC_FIRMWARE
bool "Include loadable firmware in driver"
depends on SCSI_QLOGIC_FC