*/
memcpy(skb->cb, frag_skb->cb, sizeof(skb->cb));
rts_info = IEEE80211_SKB_CB(skb);
- rts_info->flags |= IEEE80211_TX_CTL_DO_NOT_ENCRYPT;
+ rts_info->control.hw_key = NULL;
rts_info->flags &= ~IEEE80211_TX_CTL_USE_RTS_CTS;
rts_info->flags &= ~IEEE80211_TX_CTL_USE_CTS_PROTECT;
rts_info->flags &= ~IEEE80211_TX_CTL_REQ_TX_STATUS;
(struct ieee80211_rts *)(skb->data));
if (rt2x00queue_write_tx_frame(queue, skb)) {
+ dev_kfree_skb_any(skb);
WARNING(rt2x00dev, "Failed to send RTS/CTS frame.\n");
return NETDEV_TX_BUSY;
}
struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb);
struct ieee80211_hdr *ieee80211hdr = (struct ieee80211_hdr *)skb->data;
enum data_queue_qid qid = skb_get_queue_mapping(skb);
- struct rt2x00_intf *intf = vif_to_intf(tx_info->control.vif);
struct data_queue *queue;
u16 frame_control;
}
}
- /*
- * XXX: This is as wrong as the old mac80211 code was,
- * due to beacons not getting sequence numbers assigned
- * properly.
- */
- if (tx_info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) {
- if (tx_info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT)
- intf->seqno += 0x10;
- ieee80211hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG);
- ieee80211hdr->seq_ctrl |= cpu_to_le16(intf->seqno);
- }
-
if (rt2x00queue_write_tx_frame(queue, skb)) {
ieee80211_stop_queue(rt2x00dev->hw, qid);
return NETDEV_TX_BUSY;
int rt2x00mac_config(struct ieee80211_hw *hw, struct ieee80211_conf *conf)
{
struct rt2x00_dev *rt2x00dev = hw->priv;
+ int force_reconfig;
/*
* Mac80211 might be calling this function while we are trying
rt2x00lib_toggle_rx(rt2x00dev, STATE_RADIO_RX_OFF);
}
- rt2x00lib_config(rt2x00dev, conf, 0);
+ /*
+ * When the DEVICE_DIRTY_CONFIG flag is set, the device has recently
+ * been started and the configuration must be forced upon the hardware.
+ * Otherwise registers will not be intialized correctly and could
+ * result in non-working hardware because essential registers aren't
+ * initialized.
+ */
+ force_reconfig =
+ __test_and_clear_bit(DEVICE_DIRTY_CONFIG, &rt2x00dev->flags);
+
+ rt2x00lib_config(rt2x00dev, conf, force_reconfig);
/*
* Reenable RX only if the radio should be on.
else
queue->cw_max = 10; /* cw_min: 2^10 = 1024. */
- if (params->aifs >= 0)
- queue->aifs = params->aifs;
- else
- queue->aifs = 2;
+ queue->aifs = params->aifs;
INFO(rt2x00dev,
"Configured TX queue %d - CWmin: %d, CWmax: %d, Aifs: %d.\n",