module_param_named(nohwcrypt, modparam_nohwcrypt, int, 0444);
MODULE_PARM_DESC(nohwcrypt, "Disable hardware encryption.");
-int b43_modparam_qos = 1;
-module_param_named(qos, b43_modparam_qos, int, 0444);
+static int modparam_qos = 1;
+module_param_named(qos, modparam_qos, int, 0444);
MODULE_PARM_DESC(qos, "Enable QOS support (default on)");
static int modparam_btcoex = 1;
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTFHI, hi);
}
+/* Read the firmware capabilities bitmask (Opensource firmware only) */
+static u16 b43_fwcapa_read(struct b43_wldev *dev)
+{
+ B43_WARN_ON(!dev->fw.opensource);
+ return b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_FWCAPA);
+}
+
void b43_tsf_read(struct b43_wldev *dev, u64 *tsf)
{
u32 low, high;
static void b43_dump_keymemory(struct b43_wldev *dev)
{
unsigned int i, index, offset;
- DECLARE_MAC_BUF(macbuf);
u8 mac[ETH_ALEN];
u16 algo;
u32 rcmta0;
((index - 4) * 2) + 1);
*((__le32 *)(&mac[0])) = cpu_to_le32(rcmta0);
*((__le16 *)(&mac[4])) = cpu_to_le16(rcmta1);
- printk(" MAC: %s",
- print_mac(macbuf, mac));
+ printk(" MAC: %pM", mac);
} else
printk(" DEFAULT KEY");
printk("\n");
dev->fw.patch = fwpatch;
dev->fw.opensource = (fwdate == 0xFFFF);
+ /* Default to use-all-queues. */
+ dev->wl->hw->queues = dev->wl->mac80211_initially_registered_queues;
+ dev->qos_enabled = !!modparam_qos;
+ /* Default to firmware/hardware crypto acceleration. */
+ dev->hwcrypto_enabled = 1;
+
if (dev->fw.opensource) {
+ u16 fwcapa;
+
/* Patchlevel info is encoded in the "time" field. */
dev->fw.patch = fwtime;
- b43info(dev->wl, "Loading OpenSource firmware version %u.%u%s\n",
- dev->fw.rev, dev->fw.patch,
- dev->fw.pcm_request_failed ? " (Hardware crypto not supported)" : "");
+ b43info(dev->wl, "Loading OpenSource firmware version %u.%u\n",
+ dev->fw.rev, dev->fw.patch);
+
+ fwcapa = b43_fwcapa_read(dev);
+ if (!(fwcapa & B43_FWCAPA_HWCRYPTO) || dev->fw.pcm_request_failed) {
+ b43info(dev->wl, "Hardware crypto acceleration not supported by firmware\n");
+ /* Disable hardware crypto and fall back to software crypto. */
+ dev->hwcrypto_enabled = 0;
+ }
+ if (!(fwcapa & B43_FWCAPA_QOS)) {
+ b43info(dev->wl, "QoS not supported by firmware\n");
+ /* Disable QoS. Tweak hw->queues to 1. It will be restored before
+ * ieee80211_unregister to make sure the networking core can
+ * properly free possible resources. */
+ dev->wl->hw->queues = 1;
+ dev->qos_enabled = 0;
+ }
} else {
b43info(dev->wl, "Loading firmware version %u.%u "
"(20%.2i-%.2i-%.2i %.2i:%.2i:%.2i)\n",
if (phy->ops->set_rx_antenna)
phy->ops->set_rx_antenna(dev, antenna);
- if (!!conf->radio_enabled != phy->radio_on) {
- if (conf->radio_enabled) {
- b43_software_rfkill(dev, RFKILL_STATE_UNBLOCKED);
+ if (wl->radio_enabled != phy->radio_on) {
+ if (wl->radio_enabled) {
+ b43_software_rfkill(dev, false);
b43info(dev->wl, "Radio turned on by software\n");
if (!dev->radio_hw_enable) {
b43info(dev->wl, "The hardware RF-kill button "
"Press the button to turn it on.\n");
}
} else {
- b43_software_rfkill(dev, RFKILL_STATE_SOFT_BLOCKED);
+ b43_software_rfkill(dev, true);
b43info(dev->wl, "Radio turned off by software\n");
}
}
if (!dev || b43_status(dev) < B43_STAT_INITIALIZED)
goto out_unlock;
- if (dev->fw.pcm_request_failed) {
+ if (dev->fw.pcm_request_failed || !dev->hwcrypto_enabled) {
/* We don't have firmware for the crypto engine.
* Must use software-crypto. */
err = -EOPNOTSUPP;
struct b43_wldev *dev = wl->current_dev;
int did_init = 0;
int err = 0;
- bool do_rfkill_exit = 0;
/* Kill all old instance specific information to make sure
* the card won't use it in the short timeframe between start
wl->beacon0_uploaded = 0;
wl->beacon1_uploaded = 0;
wl->beacon_templates_virgin = 1;
-
- /* First register RFkill.
- * LEDs that are registered later depend on it. */
- b43_rfkill_init(dev);
+ wl->radio_enabled = 1;
mutex_lock(&wl->mutex);
if (b43_status(dev) < B43_STAT_INITIALIZED) {
err = b43_wireless_core_init(dev);
- if (err) {
- do_rfkill_exit = 1;
+ if (err)
goto out_mutex_unlock;
- }
did_init = 1;
}
if (err) {
if (did_init)
b43_wireless_core_exit(dev);
- do_rfkill_exit = 1;
goto out_mutex_unlock;
}
}
+ /* XXX: only do if device doesn't support rfkill irq */
+ wiphy_rfkill_start_polling(hw->wiphy);
+
out_mutex_unlock:
mutex_unlock(&wl->mutex);
- if (do_rfkill_exit)
- b43_rfkill_exit(dev);
-
return err;
}
struct b43_wl *wl = hw_to_b43_wl(hw);
struct b43_wldev *dev = wl->current_dev;
- b43_rfkill_exit(dev);
cancel_work_sync(&(wl->beacon_update_trigger));
mutex_lock(&wl->mutex);
if (b43_status(dev) >= B43_STAT_STARTED)
b43_wireless_core_stop(dev);
b43_wireless_core_exit(dev);
+ wl->radio_enabled = 0;
mutex_unlock(&wl->mutex);
cancel_work_sync(&(wl->txpower_adjust_work));
.sta_notify = b43_op_sta_notify,
.sw_scan_start = b43_op_sw_scan_start_notifier,
.sw_scan_complete = b43_op_sw_scan_complete_notifier,
+ .rfkill_poll = b43_rfkill_poll,
};
/* Hard-reset the chip. Do not call this directly.
B43_WARN_ON(1);
dev->phy.gmode = have_2ghz_phy;
+ dev->phy.radio_on = 1;
tmp = dev->phy.gmode ? B43_TMSLOW_GMODE : 0;
b43_wireless_core_reset(dev, tmp);
b43err(NULL, "Could not allocate ieee80211 device\n");
goto out;
}
+ wl = hw_to_b43_wl(hw);
/* fill hw info */
hw->flags = IEEE80211_HW_RX_INCLUDES_FCS |
BIT(NL80211_IFTYPE_WDS) |
BIT(NL80211_IFTYPE_ADHOC);
- hw->queues = b43_modparam_qos ? 4 : 1;
+ hw->queues = modparam_qos ? 4 : 1;
+ wl->mac80211_initially_registered_queues = hw->queues;
hw->max_rates = 2;
SET_IEEE80211_DEV(hw, dev->dev);
if (is_valid_ether_addr(sprom->et1mac))
else
SET_IEEE80211_PERM_ADDR(hw, sprom->il0mac);
- /* Get and initialize struct b43_wl */
- wl = hw_to_b43_wl(hw);
- memset(wl, 0, sizeof(*wl));
+ /* Initialize struct b43_wl */
wl->hw = hw;
spin_lock_init(&wl->irq_lock);
rwlock_init(&wl->tx_lock);
cancel_work_sync(&wldev->restart_work);
B43_WARN_ON(!wl);
- if (wl->current_dev == wldev)
+ if (wl->current_dev == wldev) {
+ /* Restore the queues count before unregistering, because firmware detect
+ * might have modified it. Restoring is important, so the networking
+ * stack can properly free resources. */
+ wl->hw->queues = wl->mac80211_initially_registered_queues;
ieee80211_unregister_hw(wl->hw);
+ }
b43_one_core_detach(dev);
static void b43_print_driverinfo(void)
{
const char *feat_pci = "", *feat_pcmcia = "", *feat_nphy = "",
- *feat_leds = "", *feat_rfkill = "";
+ *feat_leds = "";
#ifdef CONFIG_B43_PCI_AUTOSELECT
feat_pci = "P";
#endif
#ifdef CONFIG_B43_LEDS
feat_leds = "L";
-#endif
-#ifdef CONFIG_B43_RFKILL
- feat_rfkill = "R";
#endif
printk(KERN_INFO "Broadcom 43xx driver loaded "
- "[ Features: %s%s%s%s%s, Firmware-ID: "
+ "[ Features: %s%s%s%s, Firmware-ID: "
B43_SUPPORTED_FIRMWARE_ID " ]\n",
feat_pci, feat_pcmcia, feat_nphy,
- feat_leds, feat_rfkill);
+ feat_leds);
}
static int __init b43_init(void)