mutex_lock(&sc->mutex);
- if (ath9k_wiphy_started(sc)) {
- if (sc->chan_idx == curchan->hw_value) {
- /*
- * Already on the operational channel, the new wiphy
- * can be marked active.
- */
- aphy->state = ATH_WIPHY_ACTIVE;
- ieee80211_wake_queues(hw);
- } else {
- /*
- * Another wiphy is on another channel, start the new
- * wiphy in paused state.
- */
- aphy->state = ATH_WIPHY_PAUSED;
- ieee80211_stop_queues(hw);
- }
- mutex_unlock(&sc->mutex);
- return 0;
- }
- aphy->state = ATH_WIPHY_ACTIVE;
-
/* setup initial channel */
-
sc->chan_idx = curchan->hw_value;
init_channel = ath_get_curchannel(sc, hw);
struct ath_tx_control txctl;
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
- if (aphy->state != ATH_WIPHY_ACTIVE && aphy->state != ATH_WIPHY_SCAN) {
- ath_dbg(common, ATH_DBG_XMIT,
- "ath9k: %s: TX in unexpected wiphy state %d\n",
- wiphy_name(hw->wiphy), aphy->state);
- goto exit;
- }
-
if (sc->ps_enabled) {
/*
* mac80211 does not set PM field for normal data frames, so we
struct ath_softc *sc = aphy->sc;
struct ath_hw *ah = sc->sc_ah;
struct ath_common *common = ath9k_hw_common(ah);
- int i;
mutex_lock(&sc->mutex);
- aphy->state = ATH_WIPHY_INACTIVE;
-
if (led_blink)
cancel_delayed_work_sync(&sc->ath_led_blink_work);
cancel_work_sync(&sc->paprd_work);
cancel_work_sync(&sc->hw_check_work);
- for (i = 0; i < sc->num_sec_wiphy; i++) {
- if (sc->sec_wiphy[i])
- break;
- }
-
- if (i == sc->num_sec_wiphy) {
- cancel_delayed_work_sync(&sc->wiphy_work);
- cancel_work_sync(&sc->chan_work);
- }
-
if (sc->sc_flags & SC_OP_INVALID) {
ath_dbg(common, ATH_DBG_ANY, "Device not present\n");
mutex_unlock(&sc->mutex);
return;
}
- if (ath9k_wiphy_started(sc)) {
- mutex_unlock(&sc->mutex);
- return; /* another wiphy still in use */
- }
-
/* Ensure HW is awake when we try to shut it down. */
ath9k_ps_wakeup(sc);
ath9k_ps_restore(sc);
sc->ps_idle = true;
- ath9k_set_wiphy_idle(aphy, true);
ath_radio_disable(sc, hw);
sc->sc_flags |= SC_OP_INVALID;
struct ath_softc *sc = aphy->sc;
struct ath_hw *ah = sc->sc_ah;
struct ath_common *common = ath9k_hw_common(ah);
- int i;
/*
* Use the hardware MAC address as reference, the hardware uses it
ath9k_vif_iter(iter_data, vif->addr, vif);
/* Get list of all active MAC addresses */
- spin_lock_bh(&sc->wiphy_lock);
ieee80211_iterate_active_interfaces_atomic(sc->hw, ath9k_vif_iter,
iter_data);
- for (i = 0; i < sc->num_sec_wiphy; i++) {
- if (sc->sec_wiphy[i] == NULL)
- continue;
- ieee80211_iterate_active_interfaces_atomic(
- sc->sec_wiphy[i]->hw, ath9k_vif_iter, iter_data);
- }
- spin_unlock_bh(&sc->wiphy_lock);
}
/* Called with sc->mutex held. */
struct ath_hw *ah = sc->sc_ah;
struct ath_common *common = ath9k_hw_common(ah);
struct ieee80211_conf *conf = &hw->conf;
- bool disable_radio;
+ bool disable_radio = false;
mutex_lock(&sc->mutex);
* the end.
*/
if (changed & IEEE80211_CONF_CHANGE_IDLE) {
- bool enable_radio;
- bool all_wiphys_idle;
- bool idle = !!(conf->flags & IEEE80211_CONF_IDLE);
-
- spin_lock_bh(&sc->wiphy_lock);
- all_wiphys_idle = ath9k_all_wiphys_idle(sc);
- ath9k_set_wiphy_idle(aphy, idle);
-
- enable_radio = (!idle && all_wiphys_idle);
-
- /*
- * After we unlock here its possible another wiphy
- * can be re-renabled so to account for that we will
- * only disable the radio toward the end of this routine
- * if by then all wiphys are still idle.
- */
- spin_unlock_bh(&sc->wiphy_lock);
-
- if (enable_radio) {
- sc->ps_idle = false;
+ sc->ps_idle = !!(conf->flags & IEEE80211_CONF_IDLE);
+ if (!sc->ps_idle) {
ath_radio_enable(sc, hw);
ath_dbg(common, ATH_DBG_CONFIG,
"not-idle: enabling radio\n");
+ } else {
+ disable_radio = true;
}
}
if (ah->curchan)
old_pos = ah->curchan - &ah->channels[0];
- aphy->chan_idx = pos;
- aphy->chan_is_ht = conf_is_ht(conf);
if (hw->conf.flags & IEEE80211_CONF_OFFCHANNEL)
sc->sc_flags |= SC_OP_OFFCHANNEL;
else
sc->sc_flags &= ~SC_OP_OFFCHANNEL;
- if (aphy->state == ATH_WIPHY_SCAN ||
- aphy->state == ATH_WIPHY_ACTIVE)
- ath9k_wiphy_pause_all_forced(sc, aphy);
- else {
- /*
- * Do not change operational channel based on a paused
- * wiphy changes.
- */
- goto skip_chan_change;
- }
-
ath_dbg(common, ATH_DBG_CONFIG, "Set channel: %d MHz\n",
curchan->center_freq);
ath_update_survey_nf(sc, old_pos);
}
-skip_chan_change:
if (changed & IEEE80211_CONF_CHANGE_POWER) {
sc->config.txpowlimit = 2 * conf->power_level;
ath_update_txpow(sc);
}
- spin_lock_bh(&sc->wiphy_lock);
- disable_radio = ath9k_all_wiphys_idle(sc);
- spin_unlock_bh(&sc->wiphy_lock);
-
if (disable_radio) {
ath_dbg(common, ATH_DBG_CONFIG, "idle: disabling radio\n");
- sc->ps_idle = true;
ath_radio_disable(sc, hw);
}
return 0;
}
-static void ath9k_sw_scan_start(struct ieee80211_hw *hw)
-{
- struct ath_wiphy *aphy = hw->priv;
- struct ath_softc *sc = aphy->sc;
-
- mutex_lock(&sc->mutex);
- if (ath9k_wiphy_scanning(sc)) {
- /*
- * There is a race here in mac80211 but fixing it requires
- * we revisit how we handle the scan complete callback.
- * After mac80211 fixes we will not have configured hardware
- * to the home channel nor would we have configured the RX
- * filter yet.
- */
- mutex_unlock(&sc->mutex);
- return;
- }
-
- aphy->state = ATH_WIPHY_SCAN;
- ath9k_wiphy_pause_all_forced(sc, aphy);
- mutex_unlock(&sc->mutex);
-}
-
-/*
- * XXX: this requires a revisit after the driver
- * scan_complete gets moved to another place/removed in mac80211.
- */
-static void ath9k_sw_scan_complete(struct ieee80211_hw *hw)
-{
- struct ath_wiphy *aphy = hw->priv;
- struct ath_softc *sc = aphy->sc;
-
- mutex_lock(&sc->mutex);
- aphy->state = ATH_WIPHY_ACTIVE;
- mutex_unlock(&sc->mutex);
-}
-
static void ath9k_set_coverage_class(struct ieee80211_hw *hw, u8 coverage_class)
{
struct ath_wiphy *aphy = hw->priv;
.reset_tsf = ath9k_reset_tsf,
.ampdu_action = ath9k_ampdu_action,
.get_survey = ath9k_get_survey,
- .sw_scan_start = ath9k_sw_scan_start,
- .sw_scan_complete = ath9k_sw_scan_complete,
.rfkill_poll = ath9k_rfkill_poll_state,
.set_coverage_class = ath9k_set_coverage_class,
};
git.openpandora.org / pandora-kernel.git / blobdiff