static s32 e1000_swfw_sync_acquire(struct e1000_hw *hw, u16 mask);
static void e1000_swfw_sync_release(struct e1000_hw *hw, u16 mask);
-static s32 e1000_read_kmrn_reg(struct e1000_hw *hw, u32 reg_addr, u16 *data);
-static s32 e1000_write_kmrn_reg(struct e1000_hw *hw, u32 reg_addr, u16 data);
-static s32 e1000_get_software_semaphore(struct e1000_hw *hw);
-static void e1000_release_software_semaphore(struct e1000_hw *hw);
-static u8 e1000_arc_subsystem_valid(struct e1000_hw *hw);
static s32 e1000_check_downshift(struct e1000_hw *hw);
static s32 e1000_check_polarity(struct e1000_hw *hw,
e1000_rev_polarity *polarity);
static void e1000_clear_hw_cntrs(struct e1000_hw *hw);
static void e1000_clear_vfta(struct e1000_hw *hw);
-static s32 e1000_commit_shadow_ram(struct e1000_hw *hw);
static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw,
bool link_up);
static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw);
static s32 e1000_detect_gig_phy(struct e1000_hw *hw);
-static s32 e1000_erase_ich8_4k_segment(struct e1000_hw *hw, u32 bank);
static s32 e1000_get_auto_rd_done(struct e1000_hw *hw);
static s32 e1000_get_cable_length(struct e1000_hw *hw, u16 *min_length,
u16 *max_length);
static s32 e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw);
static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw);
-static s32 e1000_get_software_flag(struct e1000_hw *hw);
-static s32 e1000_ich8_cycle_init(struct e1000_hw *hw);
-static s32 e1000_ich8_flash_cycle(struct e1000_hw *hw, u32 timeout);
static s32 e1000_id_led_init(struct e1000_hw *hw);
-static s32 e1000_init_lcd_from_nvm_config_region(struct e1000_hw *hw,
- u32 cnf_base_addr,
- u32 cnf_size);
-static s32 e1000_init_lcd_from_nvm(struct e1000_hw *hw);
static void e1000_init_rx_addrs(struct e1000_hw *hw);
-static void e1000_initialize_hardware_bits(struct e1000_hw *hw);
-static bool e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw);
-static s32 e1000_kumeran_lock_loss_workaround(struct e1000_hw *hw);
-static s32 e1000_mng_enable_host_if(struct e1000_hw *hw);
-static s32 e1000_mng_host_if_write(struct e1000_hw *hw, u8 *buffer, u16 length,
- u16 offset, u8 *sum);
-static s32 e1000_mng_write_cmd_header(struct e1000_hw* hw,
- struct e1000_host_mng_command_header
- *hdr);
-static s32 e1000_mng_write_commit(struct e1000_hw *hw);
-static s32 e1000_phy_ife_get_info(struct e1000_hw *hw,
- struct e1000_phy_info *phy_info);
static s32 e1000_phy_igp_get_info(struct e1000_hw *hw,
struct e1000_phy_info *phy_info);
static s32 e1000_read_eeprom_eerd(struct e1000_hw *hw, u16 offset, u16 words,
static s32 e1000_phy_m88_get_info(struct e1000_hw *hw,
struct e1000_phy_info *phy_info);
static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw);
-static s32 e1000_read_ich8_byte(struct e1000_hw *hw, u32 index, u8 *data);
-static s32 e1000_verify_write_ich8_byte(struct e1000_hw *hw, u32 index,
- u8 byte);
-static s32 e1000_write_ich8_byte(struct e1000_hw *hw, u32 index, u8 byte);
-static s32 e1000_read_ich8_word(struct e1000_hw *hw, u32 index, u16 *data);
-static s32 e1000_read_ich8_data(struct e1000_hw *hw, u32 index, u32 size,
- u16 *data);
-static s32 e1000_write_ich8_data(struct e1000_hw *hw, u32 index, u32 size,
- u16 data);
-static s32 e1000_read_eeprom_ich8(struct e1000_hw *hw, u16 offset, u16 words,
- u16 *data);
-static s32 e1000_write_eeprom_ich8(struct e1000_hw *hw, u16 offset, u16 words,
- u16 *data);
-static void e1000_release_software_flag(struct e1000_hw *hw);
static s32 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active);
-static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active);
-static s32 e1000_set_pci_ex_no_snoop(struct e1000_hw *hw, u32 no_snoop);
-static void e1000_set_pci_express_master_disable(struct e1000_hw *hw);
static s32 e1000_wait_autoneg(struct e1000_hw *hw);
static void e1000_write_reg_io(struct e1000_hw *hw, u32 offset, u32 value);
static s32 e1000_set_phy_type(struct e1000_hw *hw);
static s32 e1000_set_vco_speed(struct e1000_hw *hw);
static s32 e1000_polarity_reversal_workaround(struct e1000_hw *hw);
static s32 e1000_set_phy_mode(struct e1000_hw *hw);
-static s32 e1000_host_if_read_cookie(struct e1000_hw *hw, u8 *buffer);
-static u8 e1000_calculate_mng_checksum(char *buffer, u32 length);
-static s32 e1000_configure_kmrn_for_10_100(struct e1000_hw *hw, u16 duplex);
-static s32 e1000_configure_kmrn_for_1000(struct e1000_hw *hw);
static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data);
static s32 e1000_do_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data);
100, 100, 100, 100, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110,
110, 110, 110, 110, 110, 110, 120, 120, 120, 120, 120, 120, 120, 120, 120, 120};
-static const
-u16 e1000_igp_2_cable_length_table[IGP02E1000_AGC_LENGTH_TABLE_SIZE] =
- { 0, 0, 0, 0, 0, 0, 0, 0, 3, 5, 8, 11, 13, 16, 18, 21,
- 0, 0, 0, 3, 6, 10, 13, 16, 19, 23, 26, 29, 32, 35, 38, 41,
- 6, 10, 14, 18, 22, 26, 30, 33, 37, 41, 44, 48, 51, 54, 58, 61,
- 21, 26, 31, 35, 40, 44, 49, 53, 57, 61, 65, 68, 72, 75, 79, 82,
- 40, 45, 51, 56, 61, 66, 70, 75, 79, 83, 87, 91, 94, 98, 101, 104,
- 60, 66, 72, 77, 82, 87, 92, 96, 100, 104, 108, 111, 114, 117, 119, 121,
- 83, 89, 95, 100, 105, 109, 113, 116, 119, 122, 124,
- 104, 109, 114, 118, 121, 124};
-
static DEFINE_SPINLOCK(e1000_eeprom_lock);
/******************************************************************************
hw->phy_type = e1000_phy_igp;
break;
}
- case IGP03E1000_E_PHY_ID:
- hw->phy_type = e1000_phy_igp_3;
- break;
- case IFE_E_PHY_ID:
- case IFE_PLUS_E_PHY_ID:
- case IFE_C_E_PHY_ID:
- hw->phy_type = e1000_phy_ife;
- break;
- case GG82563_E_PHY_ID:
- if (hw->mac_type == e1000_80003es2lan) {
- hw->phy_type = e1000_phy_gg82563;
- break;
- }
- /* Fall Through */
default:
/* Should never have loaded on this device */
hw->phy_type = e1000_phy_undefined;
case E1000_DEV_ID_82547GI:
hw->mac_type = e1000_82547_rev_2;
break;
- case E1000_DEV_ID_82571EB_COPPER:
- case E1000_DEV_ID_82571EB_FIBER:
- case E1000_DEV_ID_82571EB_SERDES:
- case E1000_DEV_ID_82571EB_SERDES_DUAL:
- case E1000_DEV_ID_82571EB_SERDES_QUAD:
- case E1000_DEV_ID_82571EB_QUAD_COPPER:
- case E1000_DEV_ID_82571PT_QUAD_COPPER:
- case E1000_DEV_ID_82571EB_QUAD_FIBER:
- case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE:
- hw->mac_type = e1000_82571;
- break;
- case E1000_DEV_ID_82572EI_COPPER:
- case E1000_DEV_ID_82572EI_FIBER:
- case E1000_DEV_ID_82572EI_SERDES:
- case E1000_DEV_ID_82572EI:
- hw->mac_type = e1000_82572;
- break;
- case E1000_DEV_ID_82573E:
- case E1000_DEV_ID_82573E_IAMT:
- case E1000_DEV_ID_82573L:
- hw->mac_type = e1000_82573;
- break;
- case E1000_DEV_ID_80003ES2LAN_COPPER_SPT:
- case E1000_DEV_ID_80003ES2LAN_SERDES_SPT:
- case E1000_DEV_ID_80003ES2LAN_COPPER_DPT:
- case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
- hw->mac_type = e1000_80003es2lan;
- break;
- case E1000_DEV_ID_ICH8_IGP_M_AMT:
- case E1000_DEV_ID_ICH8_IGP_AMT:
- case E1000_DEV_ID_ICH8_IGP_C:
- case E1000_DEV_ID_ICH8_IFE:
- case E1000_DEV_ID_ICH8_IFE_GT:
- case E1000_DEV_ID_ICH8_IFE_G:
- case E1000_DEV_ID_ICH8_IGP_M:
- hw->mac_type = e1000_ich8lan;
- break;
default:
/* Should never have loaded on this device */
return -E1000_ERR_MAC_TYPE;
}
switch (hw->mac_type) {
- case e1000_ich8lan:
- hw->swfwhw_semaphore_present = true;
- hw->asf_firmware_present = true;
- break;
- case e1000_80003es2lan:
- hw->swfw_sync_present = true;
- /* fall through */
- case e1000_82571:
- case e1000_82572:
- case e1000_82573:
- hw->eeprom_semaphore_present = true;
- /* fall through */
case e1000_82541:
case e1000_82547:
case e1000_82541_rev_2:
if (hw->mac_type == e1000_82543)
hw->bad_tx_carr_stats_fd = true;
- /* capable of receiving management packets to the host */
- if (hw->mac_type >= e1000_82571)
- hw->has_manc2h = true;
-
- /* In rare occasions, ESB2 systems would end up started without
- * the RX unit being turned on.
- */
- if (hw->mac_type == e1000_80003es2lan)
- hw->rx_needs_kicking = true;
-
if (hw->mac_type > e1000_82544)
hw->has_smbus = true;
switch (hw->device_id) {
case E1000_DEV_ID_82545GM_SERDES:
case E1000_DEV_ID_82546GB_SERDES:
- case E1000_DEV_ID_82571EB_SERDES:
- case E1000_DEV_ID_82571EB_SERDES_DUAL:
- case E1000_DEV_ID_82571EB_SERDES_QUAD:
- case E1000_DEV_ID_82572EI_SERDES:
- case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
hw->media_type = e1000_media_type_internal_serdes;
break;
default:
case e1000_82542_rev2_1:
hw->media_type = e1000_media_type_fiber;
break;
- case e1000_ich8lan:
- case e1000_82573:
- /* The STATUS_TBIMODE bit is reserved or reused for the this
- * device.
- */
- hw->media_type = e1000_media_type_copper;
- break;
default:
status = er32(STATUS);
if (status & E1000_STATUS_TBIMODE) {
u32 icr;
u32 manc;
u32 led_ctrl;
- u32 timeout;
- u32 extcnf_ctrl;
s32 ret_val;
DEBUGFUNC("e1000_reset_hw");
e1000_pci_clear_mwi(hw);
}
- if (hw->bus_type == e1000_bus_type_pci_express) {
- /* Prevent the PCI-E bus from sticking if there is no TLP connection
- * on the last TLP read/write transaction when MAC is reset.
- */
- if (e1000_disable_pciex_master(hw) != E1000_SUCCESS) {
- DEBUGOUT("PCI-E Master disable polling has failed.\n");
- }
- }
-
/* Clear interrupt mask to stop board from generating interrupts */
DEBUGOUT("Masking off all interrupts\n");
ew32(IMC, 0xffffffff);
msleep(5);
}
- /* Must acquire the MDIO ownership before MAC reset.
- * Ownership defaults to firmware after a reset. */
- if (hw->mac_type == e1000_82573) {
- timeout = 10;
-
- extcnf_ctrl = er32(EXTCNF_CTRL);
- extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
-
- do {
- ew32(EXTCNF_CTRL, extcnf_ctrl);
- extcnf_ctrl = er32(EXTCNF_CTRL);
-
- if (extcnf_ctrl & E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP)
- break;
- else
- extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
-
- msleep(2);
- timeout--;
- } while (timeout);
- }
-
- /* Workaround for ICH8 bit corruption issue in FIFO memory */
- if (hw->mac_type == e1000_ich8lan) {
- /* Set Tx and Rx buffer allocation to 8k apiece. */
- ew32(PBA, E1000_PBA_8K);
- /* Set Packet Buffer Size to 16k. */
- ew32(PBS, E1000_PBS_16K);
- }
-
/* Issue a global reset to the MAC. This will reset the chip's
* transmit, receive, DMA, and link units. It will not effect
* the current PCI configuration. The global reset bit is self-
/* Reset is performed on a shadow of the control register */
ew32(CTRL_DUP, (ctrl | E1000_CTRL_RST));
break;
- case e1000_ich8lan:
- if (!hw->phy_reset_disable &&
- e1000_check_phy_reset_block(hw) == E1000_SUCCESS) {
- /* e1000_ich8lan PHY HW reset requires MAC CORE reset
- * at the same time to make sure the interface between
- * MAC and the external PHY is reset.
- */
- ctrl |= E1000_CTRL_PHY_RST;
- }
-
- e1000_get_software_flag(hw);
- ew32(CTRL, (ctrl | E1000_CTRL_RST));
- msleep(5);
- break;
default:
ew32(CTRL, (ctrl | E1000_CTRL_RST));
break;
/* Wait for EEPROM reload */
msleep(20);
break;
- case e1000_82573:
- if (!e1000_is_onboard_nvm_eeprom(hw)) {
- udelay(10);
- ctrl_ext = er32(CTRL_EXT);
- ctrl_ext |= E1000_CTRL_EXT_EE_RST;
- ew32(CTRL_EXT, ctrl_ext);
- E1000_WRITE_FLUSH();
- }
- /* fall through */
default:
/* Auto read done will delay 5ms or poll based on mac type */
ret_val = e1000_get_auto_rd_done(hw);
}
/* Disable HW ARPs on ASF enabled adapters */
- if (hw->mac_type >= e1000_82540 && hw->mac_type <= e1000_82547_rev_2) {
+ if (hw->mac_type >= e1000_82540) {
manc = er32(MANC);
manc &= ~(E1000_MANC_ARP_EN);
ew32(MANC, manc);
e1000_pci_set_mwi(hw);
}
- if (hw->mac_type == e1000_ich8lan) {
- u32 kab = er32(KABGTXD);
- kab |= E1000_KABGTXD_BGSQLBIAS;
- ew32(KABGTXD, kab);
- }
-
return E1000_SUCCESS;
}
-/******************************************************************************
- *
- * Initialize a number of hardware-dependent bits
- *
- * hw: Struct containing variables accessed by shared code
- *
- * This function contains hardware limitation workarounds for PCI-E adapters
- *
- *****************************************************************************/
-static void e1000_initialize_hardware_bits(struct e1000_hw *hw)
-{
- if ((hw->mac_type >= e1000_82571) && (!hw->initialize_hw_bits_disable)) {
- /* Settings common to all PCI-express silicon */
- u32 reg_ctrl, reg_ctrl_ext;
- u32 reg_tarc0, reg_tarc1;
- u32 reg_tctl;
- u32 reg_txdctl, reg_txdctl1;
-
- /* link autonegotiation/sync workarounds */
- reg_tarc0 = er32(TARC0);
- reg_tarc0 &= ~((1 << 30)|(1 << 29)|(1 << 28)|(1 << 27));
-
- /* Enable not-done TX descriptor counting */
- reg_txdctl = er32(TXDCTL);
- reg_txdctl |= E1000_TXDCTL_COUNT_DESC;
- ew32(TXDCTL, reg_txdctl);
- reg_txdctl1 = er32(TXDCTL1);
- reg_txdctl1 |= E1000_TXDCTL_COUNT_DESC;
- ew32(TXDCTL1, reg_txdctl1);
-
- switch (hw->mac_type) {
- case e1000_82571:
- case e1000_82572:
- /* Clear PHY TX compatible mode bits */
- reg_tarc1 = er32(TARC1);
- reg_tarc1 &= ~((1 << 30)|(1 << 29));
-
- /* link autonegotiation/sync workarounds */
- reg_tarc0 |= ((1 << 26)|(1 << 25)|(1 << 24)|(1 << 23));
-
- /* TX ring control fixes */
- reg_tarc1 |= ((1 << 26)|(1 << 25)|(1 << 24));
-
- /* Multiple read bit is reversed polarity */
- reg_tctl = er32(TCTL);
- if (reg_tctl & E1000_TCTL_MULR)
- reg_tarc1 &= ~(1 << 28);
- else
- reg_tarc1 |= (1 << 28);
-
- ew32(TARC1, reg_tarc1);
- break;
- case e1000_82573:
- reg_ctrl_ext = er32(CTRL_EXT);
- reg_ctrl_ext &= ~(1 << 23);
- reg_ctrl_ext |= (1 << 22);
-
- /* TX byte count fix */
- reg_ctrl = er32(CTRL);
- reg_ctrl &= ~(1 << 29);
-
- ew32(CTRL_EXT, reg_ctrl_ext);
- ew32(CTRL, reg_ctrl);
- break;
- case e1000_80003es2lan:
- /* improve small packet performace for fiber/serdes */
- if ((hw->media_type == e1000_media_type_fiber) ||
- (hw->media_type == e1000_media_type_internal_serdes)) {
- reg_tarc0 &= ~(1 << 20);
- }
-
- /* Multiple read bit is reversed polarity */
- reg_tctl = er32(TCTL);
- reg_tarc1 = er32(TARC1);
- if (reg_tctl & E1000_TCTL_MULR)
- reg_tarc1 &= ~(1 << 28);
- else
- reg_tarc1 |= (1 << 28);
-
- ew32(TARC1, reg_tarc1);
- break;
- case e1000_ich8lan:
- /* Reduce concurrent DMA requests to 3 from 4 */
- if ((hw->revision_id < 3) ||
- ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) &&
- (hw->device_id != E1000_DEV_ID_ICH8_IGP_M)))
- reg_tarc0 |= ((1 << 29)|(1 << 28));
-
- reg_ctrl_ext = er32(CTRL_EXT);
- reg_ctrl_ext |= (1 << 22);
- ew32(CTRL_EXT, reg_ctrl_ext);
-
- /* workaround TX hang with TSO=on */
- reg_tarc0 |= ((1 << 27)|(1 << 26)|(1 << 24)|(1 << 23));
-
- /* Multiple read bit is reversed polarity */
- reg_tctl = er32(TCTL);
- reg_tarc1 = er32(TARC1);
- if (reg_tctl & E1000_TCTL_MULR)
- reg_tarc1 &= ~(1 << 28);
- else
- reg_tarc1 |= (1 << 28);
-
- /* workaround TX hang with TSO=on */
- reg_tarc1 |= ((1 << 30)|(1 << 26)|(1 << 24));
-
- ew32(TARC1, reg_tarc1);
- break;
- default:
- break;
- }
-
- ew32(TARC0, reg_tarc0);
- }
-}
-
/******************************************************************************
* Performs basic configuration of the adapter.
*
u32 i;
s32 ret_val;
u32 mta_size;
- u32 reg_data;
u32 ctrl_ext;
DEBUGFUNC("e1000_init_hw");
- /* force full DMA clock frequency for 10/100 on ICH8 A0-B0 */
- if ((hw->mac_type == e1000_ich8lan) &&
- ((hw->revision_id < 3) ||
- ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) &&
- (hw->device_id != E1000_DEV_ID_ICH8_IGP_M)))) {
- reg_data = er32(STATUS);
- reg_data &= ~0x80000000;
- ew32(STATUS, reg_data);
- }
-
/* Initialize Identification LED */
ret_val = e1000_id_led_init(hw);
if (ret_val) {
/* Set the media type and TBI compatibility */
e1000_set_media_type(hw);
- /* Must be called after e1000_set_media_type because media_type is used */
- e1000_initialize_hardware_bits(hw);
-
/* Disabling VLAN filtering. */
DEBUGOUT("Initializing the IEEE VLAN\n");
- /* VET hardcoded to standard value and VFTA removed in ICH8 LAN */
- if (hw->mac_type != e1000_ich8lan) {
- if (hw->mac_type < e1000_82545_rev_3)
- ew32(VET, 0);
- e1000_clear_vfta(hw);
- }
+ if (hw->mac_type < e1000_82545_rev_3)
+ ew32(VET, 0);
+ e1000_clear_vfta(hw);
/* For 82542 (rev 2.0), disable MWI and put the receiver into reset */
if (hw->mac_type == e1000_82542_rev2_0) {
/* Zero out the Multicast HASH table */
DEBUGOUT("Zeroing the MTA\n");
mta_size = E1000_MC_TBL_SIZE;
- if (hw->mac_type == e1000_ich8lan)
- mta_size = E1000_MC_TBL_SIZE_ICH8LAN;
for (i = 0; i < mta_size; i++) {
E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
/* use write flush to prevent Memory Write Block (MWB) from
break;
}
- /* More time needed for PHY to initialize */
- if (hw->mac_type == e1000_ich8lan)
- msleep(15);
-
/* Call a subroutine to configure the link and setup flow control. */
ret_val = e1000_setup_link(hw);
ew32(TXDCTL, ctrl);
}
- if (hw->mac_type == e1000_82573) {
- e1000_enable_tx_pkt_filtering(hw);
- }
-
- switch (hw->mac_type) {
- default:
- break;
- case e1000_80003es2lan:
- /* Enable retransmit on late collisions */
- reg_data = er32(TCTL);
- reg_data |= E1000_TCTL_RTLC;
- ew32(TCTL, reg_data);
-
- /* Configure Gigabit Carry Extend Padding */
- reg_data = er32(TCTL_EXT);
- reg_data &= ~E1000_TCTL_EXT_GCEX_MASK;
- reg_data |= DEFAULT_80003ES2LAN_TCTL_EXT_GCEX;
- ew32(TCTL_EXT, reg_data);
-
- /* Configure Transmit Inter-Packet Gap */
- reg_data = er32(TIPG);
- reg_data &= ~E1000_TIPG_IPGT_MASK;
- reg_data |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000;
- ew32(TIPG, reg_data);
-
- reg_data = E1000_READ_REG_ARRAY(hw, FFLT, 0x0001);
- reg_data &= ~0x00100000;
- E1000_WRITE_REG_ARRAY(hw, FFLT, 0x0001, reg_data);
- /* Fall through */
- case e1000_82571:
- case e1000_82572:
- case e1000_ich8lan:
- ctrl = er32(TXDCTL1);
- ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB;
- ew32(TXDCTL1, ctrl);
- break;
- }
-
-
- if (hw->mac_type == e1000_82573) {
- u32 gcr = er32(GCR);
- gcr |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX;
- ew32(GCR, gcr);
- }
-
/* Clear all of the statistics registers (clear on read). It is
* important that we do this after we have tried to establish link
* because the symbol error count will increment wildly if there
*/
e1000_clear_hw_cntrs(hw);
- /* ICH8 No-snoop bits are opposite polarity.
- * Set to snoop by default after reset. */
- if (hw->mac_type == e1000_ich8lan)
- e1000_set_pci_ex_no_snoop(hw, PCI_EX_82566_SNOOP_ALL);
-
if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER ||
hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) {
ctrl_ext = er32(CTRL_EXT);
DEBUGFUNC("e1000_setup_link");
- /* In the case of the phy reset being blocked, we already have a link.
- * We do not have to set it up again. */
- if (e1000_check_phy_reset_block(hw))
- return E1000_SUCCESS;
-
/* Read and store word 0x0F of the EEPROM. This word contains bits
* that determine the hardware's default PAUSE (flow control) mode,
* a bit that determines whether the HW defaults to enabling or
* be initialized based on a value in the EEPROM.
*/
if (hw->fc == E1000_FC_DEFAULT) {
- switch (hw->mac_type) {
- case e1000_ich8lan:
- case e1000_82573:
- hw->fc = E1000_FC_FULL;
- break;
- default:
- ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG,
- 1, &eeprom_data);
- if (ret_val) {
- DEBUGOUT("EEPROM Read Error\n");
- return -E1000_ERR_EEPROM;
- }
- if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0)
- hw->fc = E1000_FC_NONE;
- else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) ==
- EEPROM_WORD0F_ASM_DIR)
- hw->fc = E1000_FC_TX_PAUSE;
- else
- hw->fc = E1000_FC_FULL;
- break;
+ ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG,
+ 1, &eeprom_data);
+ if (ret_val) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
}
+ if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0)
+ hw->fc = E1000_FC_NONE;
+ else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) ==
+ EEPROM_WORD0F_ASM_DIR)
+ hw->fc = E1000_FC_TX_PAUSE;
+ else
+ hw->fc = E1000_FC_FULL;
}
/* We want to save off the original Flow Control configuration just
*/
DEBUGOUT("Initializing the Flow Control address, type and timer regs\n");
- /* FCAL/H and FCT are hardcoded to standard values in e1000_ich8lan. */
- if (hw->mac_type != e1000_ich8lan) {
- ew32(FCT, FLOW_CONTROL_TYPE);
- ew32(FCAH, FLOW_CONTROL_ADDRESS_HIGH);
- ew32(FCAL, FLOW_CONTROL_ADDRESS_LOW);
- }
+ ew32(FCT, FLOW_CONTROL_TYPE);
+ ew32(FCAH, FLOW_CONTROL_ADDRESS_HIGH);
+ ew32(FCAL, FLOW_CONTROL_ADDRESS_LOW);
ew32(FCTTV, hw->fc_pause_time);
DEBUGFUNC("e1000_setup_fiber_serdes_link");
- /* On 82571 and 82572 Fiber connections, SerDes loopback mode persists
- * until explicitly turned off or a power cycle is performed. A read to
- * the register does not indicate its status. Therefore, we ensure
- * loopback mode is disabled during initialization.
- */
- if (hw->mac_type == e1000_82571 || hw->mac_type == e1000_82572)
- ew32(SCTL, E1000_DISABLE_SERDES_LOOPBACK);
-
/* On adapters with a MAC newer than 82544, SWDP 1 will be
* set when the optics detect a signal. On older adapters, it will be
* cleared when there is a signal. This applies to fiber media only.
/* Wait 15ms for MAC to configure PHY from eeprom settings */
msleep(15);
- if (hw->mac_type != e1000_ich8lan) {
/* Configure activity LED after PHY reset */
led_ctrl = er32(LEDCTL);
led_ctrl &= IGP_ACTIVITY_LED_MASK;
led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
ew32(LEDCTL, led_ctrl);
- }
/* The NVM settings will configure LPLU in D3 for IGP2 and IGP3 PHYs */
if (hw->phy_type == e1000_phy_igp) {
}
}
- /* disable lplu d0 during driver init */
- ret_val = e1000_set_d0_lplu_state(hw, false);
- if (ret_val) {
- DEBUGOUT("Error Disabling LPLU D0\n");
- return ret_val;
- }
/* Configure mdi-mdix settings */
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
if (ret_val)
return E1000_SUCCESS;
}
-/********************************************************************
-* Copper link setup for e1000_phy_gg82563 series.
-*
-* hw - Struct containing variables accessed by shared code
-*********************************************************************/
-static s32 e1000_copper_link_ggp_setup(struct e1000_hw *hw)
-{
- s32 ret_val;
- u16 phy_data;
- u32 reg_data;
-
- DEBUGFUNC("e1000_copper_link_ggp_setup");
-
- if (!hw->phy_reset_disable) {
-
- /* Enable CRS on TX for half-duplex operation. */
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
- /* Use 25MHz for both link down and 1000BASE-T for Tx clock */
- phy_data |= GG82563_MSCR_TX_CLK_1000MBPS_25MHZ;
-
- ret_val = e1000_write_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL,
- phy_data);
- if (ret_val)
- return ret_val;
-
- /* Options:
- * MDI/MDI-X = 0 (default)
- * 0 - Auto for all speeds
- * 1 - MDI mode
- * 2 - MDI-X mode
- * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
- */
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_SPEC_CTRL, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK;
-
- switch (hw->mdix) {
- case 1:
- phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDI;
- break;
- case 2:
- phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDIX;
- break;
- case 0:
- default:
- phy_data |= GG82563_PSCR_CROSSOVER_MODE_AUTO;
- break;
- }
-
- /* Options:
- * disable_polarity_correction = 0 (default)
- * Automatic Correction for Reversed Cable Polarity
- * 0 - Disabled
- * 1 - Enabled
- */
- phy_data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
- if (hw->disable_polarity_correction == 1)
- phy_data |= GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
- ret_val = e1000_write_phy_reg(hw, GG82563_PHY_SPEC_CTRL, phy_data);
-
- if (ret_val)
- return ret_val;
-
- /* SW Reset the PHY so all changes take effect */
- ret_val = e1000_phy_reset(hw);
- if (ret_val) {
- DEBUGOUT("Error Resetting the PHY\n");
- return ret_val;
- }
- } /* phy_reset_disable */
-
- if (hw->mac_type == e1000_80003es2lan) {
- /* Bypass RX and TX FIFO's */
- ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL,
- E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS |
- E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS);
- if (ret_val)
- return ret_val;
-
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_SPEC_CTRL_2, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG;
- ret_val = e1000_write_phy_reg(hw, GG82563_PHY_SPEC_CTRL_2, phy_data);
-
- if (ret_val)
- return ret_val;
-
- reg_data = er32(CTRL_EXT);
- reg_data &= ~(E1000_CTRL_EXT_LINK_MODE_MASK);
- ew32(CTRL_EXT, reg_data);
-
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_PWR_MGMT_CTRL,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- /* Do not init these registers when the HW is in IAMT mode, since the
- * firmware will have already initialized them. We only initialize
- * them if the HW is not in IAMT mode.
- */
- if (!e1000_check_mng_mode(hw)) {
- /* Enable Electrical Idle on the PHY */
- phy_data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE;
- ret_val = e1000_write_phy_reg(hw, GG82563_PHY_PWR_MGMT_CTRL,
- phy_data);
- if (ret_val)
- return ret_val;
-
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
- ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL,
- phy_data);
-
- if (ret_val)
- return ret_val;
- }
-
- /* Workaround: Disable padding in Kumeran interface in the MAC
- * and in the PHY to avoid CRC errors.
- */
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_INBAND_CTRL,
- &phy_data);
- if (ret_val)
- return ret_val;
- phy_data |= GG82563_ICR_DIS_PADDING;
- ret_val = e1000_write_phy_reg(hw, GG82563_PHY_INBAND_CTRL,
- phy_data);
- if (ret_val)
- return ret_val;
- }
-
- return E1000_SUCCESS;
-}
-
/********************************************************************
* Copper link setup for e1000_phy_m88 series.
*
if (hw->autoneg_advertised == 0)
hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT;
- /* IFE phy only supports 10/100 */
- if (hw->phy_type == e1000_phy_ife)
- hw->autoneg_advertised &= AUTONEG_ADVERTISE_10_100_ALL;
-
DEBUGOUT("Reconfiguring auto-neg advertisement params\n");
ret_val = e1000_phy_setup_autoneg(hw);
if (ret_val) {
s32 ret_val;
u16 i;
u16 phy_data;
- u16 reg_data = 0;
DEBUGFUNC("e1000_setup_copper_link");
- switch (hw->mac_type) {
- case e1000_80003es2lan:
- case e1000_ich8lan:
- /* Set the mac to wait the maximum time between each
- * iteration and increase the max iterations when
- * polling the phy; this fixes erroneous timeouts at 10Mbps. */
- ret_val = e1000_write_kmrn_reg(hw, GG82563_REG(0x34, 4), 0xFFFF);
- if (ret_val)
- return ret_val;
- ret_val = e1000_read_kmrn_reg(hw, GG82563_REG(0x34, 9), ®_data);
- if (ret_val)
- return ret_val;
- reg_data |= 0x3F;
- ret_val = e1000_write_kmrn_reg(hw, GG82563_REG(0x34, 9), reg_data);
- if (ret_val)
- return ret_val;
- default:
- break;
- }
-
/* Check if it is a valid PHY and set PHY mode if necessary. */
ret_val = e1000_copper_link_preconfig(hw);
if (ret_val)
return ret_val;
- switch (hw->mac_type) {
- case e1000_80003es2lan:
- /* Kumeran registers are written-only */
- reg_data = E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT;
- reg_data |= E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING;
- ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_INB_CTRL,
- reg_data);
- if (ret_val)
- return ret_val;
- break;
- default:
- break;
- }
-
- if (hw->phy_type == e1000_phy_igp ||
- hw->phy_type == e1000_phy_igp_3 ||
- hw->phy_type == e1000_phy_igp_2) {
+ if (hw->phy_type == e1000_phy_igp) {
ret_val = e1000_copper_link_igp_setup(hw);
if (ret_val)
return ret_val;
ret_val = e1000_copper_link_mgp_setup(hw);
if (ret_val)
return ret_val;
- } else if (hw->phy_type == e1000_phy_gg82563) {
- ret_val = e1000_copper_link_ggp_setup(hw);
- if (ret_val)
- return ret_val;
}
if (hw->autoneg) {
}
/******************************************************************************
-* Configure the MAC-to-PHY interface for 10/100Mbps
+* Configures PHY autoneg and flow control advertisement settings
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
-static s32 e1000_configure_kmrn_for_10_100(struct e1000_hw *hw, u16 duplex)
+s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
{
- s32 ret_val = E1000_SUCCESS;
- u32 tipg;
- u16 reg_data;
+ s32 ret_val;
+ u16 mii_autoneg_adv_reg;
+ u16 mii_1000t_ctrl_reg;
- DEBUGFUNC("e1000_configure_kmrn_for_10_100");
+ DEBUGFUNC("e1000_phy_setup_autoneg");
- reg_data = E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT;
- ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_HD_CTRL,
- reg_data);
+ /* Read the MII Auto-Neg Advertisement Register (Address 4). */
+ ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
if (ret_val)
return ret_val;
- /* Configure Transmit Inter-Packet Gap */
- tipg = er32(TIPG);
- tipg &= ~E1000_TIPG_IPGT_MASK;
- tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_10_100;
- ew32(TIPG, tipg);
-
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data);
-
+ /* Read the MII 1000Base-T Control Register (Address 9). */
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
if (ret_val)
return ret_val;
- if (duplex == HALF_DUPLEX)
- reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER;
- else
- reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
-
- ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
+ /* Need to parse both autoneg_advertised and fc and set up
+ * the appropriate PHY registers. First we will parse for
+ * autoneg_advertised software override. Since we can advertise
+ * a plethora of combinations, we need to check each bit
+ * individually.
+ */
- return ret_val;
-}
+ /* First we clear all the 10/100 mb speed bits in the Auto-Neg
+ * Advertisement Register (Address 4) and the 1000 mb speed bits in
+ * the 1000Base-T Control Register (Address 9).
+ */
+ mii_autoneg_adv_reg &= ~REG4_SPEED_MASK;
+ mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK;
-static s32 e1000_configure_kmrn_for_1000(struct e1000_hw *hw)
-{
- s32 ret_val = E1000_SUCCESS;
- u16 reg_data;
- u32 tipg;
+ DEBUGOUT1("autoneg_advertised %x\n", hw->autoneg_advertised);
- DEBUGFUNC("e1000_configure_kmrn_for_1000");
-
- reg_data = E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT;
- ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_HD_CTRL,
- reg_data);
- if (ret_val)
- return ret_val;
-
- /* Configure Transmit Inter-Packet Gap */
- tipg = er32(TIPG);
- tipg &= ~E1000_TIPG_IPGT_MASK;
- tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000;
- ew32(TIPG, tipg);
-
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data);
-
- if (ret_val)
- return ret_val;
-
- reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
- ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
-
- return ret_val;
-}
-
-/******************************************************************************
-* Configures PHY autoneg and flow control advertisement settings
-*
-* hw - Struct containing variables accessed by shared code
-******************************************************************************/
-s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
-{
- s32 ret_val;
- u16 mii_autoneg_adv_reg;
- u16 mii_1000t_ctrl_reg;
-
- DEBUGFUNC("e1000_phy_setup_autoneg");
-
- /* Read the MII Auto-Neg Advertisement Register (Address 4). */
- ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
- if (ret_val)
- return ret_val;
-
- if (hw->phy_type != e1000_phy_ife) {
- /* Read the MII 1000Base-T Control Register (Address 9). */
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
- if (ret_val)
- return ret_val;
- } else
- mii_1000t_ctrl_reg=0;
-
- /* Need to parse both autoneg_advertised and fc and set up
- * the appropriate PHY registers. First we will parse for
- * autoneg_advertised software override. Since we can advertise
- * a plethora of combinations, we need to check each bit
- * individually.
- */
-
- /* First we clear all the 10/100 mb speed bits in the Auto-Neg
- * Advertisement Register (Address 4) and the 1000 mb speed bits in
- * the 1000Base-T Control Register (Address 9).
- */
- mii_autoneg_adv_reg &= ~REG4_SPEED_MASK;
- mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK;
-
- DEBUGOUT1("autoneg_advertised %x\n", hw->autoneg_advertised);
-
- /* Do we want to advertise 10 Mb Half Duplex? */
- if (hw->autoneg_advertised & ADVERTISE_10_HALF) {
- DEBUGOUT("Advertise 10mb Half duplex\n");
- mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
- }
+ /* Do we want to advertise 10 Mb Half Duplex? */
+ if (hw->autoneg_advertised & ADVERTISE_10_HALF) {
+ DEBUGOUT("Advertise 10mb Half duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
+ }
/* Do we want to advertise 10 Mb Full Duplex? */
if (hw->autoneg_advertised & ADVERTISE_10_FULL) {
if (hw->autoneg_advertised & ADVERTISE_1000_FULL) {
DEBUGOUT("Advertise 1000mb Full duplex\n");
mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
- if (hw->phy_type == e1000_phy_ife) {
- DEBUGOUT("e1000_phy_ife is a 10/100 PHY. Gigabit speed is not supported.\n");
- }
}
/* Check for a software override of the flow control settings, and
DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
- if (hw->phy_type != e1000_phy_ife) {
- ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
- if (ret_val)
- return ret_val;
- }
+ ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
+ if (ret_val)
+ return ret_val;
return E1000_SUCCESS;
}
/* Write the configured values back to the Device Control Reg. */
ew32(CTRL, ctrl);
- if ((hw->phy_type == e1000_phy_m88) ||
- (hw->phy_type == e1000_phy_gg82563)) {
+ if (hw->phy_type == e1000_phy_m88) {
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
if (ret_val)
return ret_val;
/* Need to reset the PHY or these changes will be ignored */
mii_ctrl_reg |= MII_CR_RESET;
- /* Disable MDI-X support for 10/100 */
- } else if (hw->phy_type == e1000_phy_ife) {
- ret_val = e1000_read_phy_reg(hw, IFE_PHY_MDIX_CONTROL, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data &= ~IFE_PMC_AUTO_MDIX;
- phy_data &= ~IFE_PMC_FORCE_MDIX;
-
- ret_val = e1000_write_phy_reg(hw, IFE_PHY_MDIX_CONTROL, phy_data);
- if (ret_val)
- return ret_val;
-
} else {
/* Clear Auto-Crossover to force MDI manually. IGP requires MDI
* forced whenever speed or duplex are forced.
msleep(100);
}
if ((i == 0) &&
- ((hw->phy_type == e1000_phy_m88) ||
- (hw->phy_type == e1000_phy_gg82563))) {
+ (hw->phy_type == e1000_phy_m88)) {
/* We didn't get link. Reset the DSP and wait again for link. */
ret_val = e1000_phy_reset_dsp(hw);
if (ret_val) {
if (ret_val)
return ret_val;
}
- } else if (hw->phy_type == e1000_phy_gg82563) {
- /* The TX_CLK of the Extended PHY Specific Control Register defaults
- * to 2.5MHz on a reset. We need to re-force it back to 25MHz, if
- * we're not in a forced 10/duplex configuration. */
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data &= ~GG82563_MSCR_TX_CLK_MASK;
- if ((hw->forced_speed_duplex == e1000_10_full) ||
- (hw->forced_speed_duplex == e1000_10_half))
- phy_data |= GG82563_MSCR_TX_CLK_10MBPS_2_5MHZ;
- else
- phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25MHZ;
-
- /* Also due to the reset, we need to enable CRS on Tx. */
- phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
-
- ret_val = e1000_write_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, phy_data);
- if (ret_val)
- return ret_val;
}
return E1000_SUCCESS;
}
}
}
- if ((hw->mac_type == e1000_80003es2lan) &&
- (hw->media_type == e1000_media_type_copper)) {
- if (*speed == SPEED_1000)
- ret_val = e1000_configure_kmrn_for_1000(hw);
- else
- ret_val = e1000_configure_kmrn_for_10_100(hw, *duplex);
- if (ret_val)
- return ret_val;
- }
-
- if ((hw->phy_type == e1000_phy_igp_3) && (*speed == SPEED_1000)) {
- ret_val = e1000_kumeran_lock_loss_workaround(hw);
- if (ret_val)
- return ret_val;
- }
-
return E1000_SUCCESS;
}
DEBUGFUNC("e1000_swfw_sync_acquire");
- if (hw->swfwhw_semaphore_present)
- return e1000_get_software_flag(hw);
-
if (!hw->swfw_sync_present)
return e1000_get_hw_eeprom_semaphore(hw);
DEBUGFUNC("e1000_swfw_sync_release");
- if (hw->swfwhw_semaphore_present) {
- e1000_release_software_flag(hw);
- return;
- }
-
if (!hw->swfw_sync_present) {
e1000_put_hw_eeprom_semaphore(hw);
return;
DEBUGFUNC("e1000_read_phy_reg");
- if ((hw->mac_type == e1000_80003es2lan) &&
- (er32(STATUS) & E1000_STATUS_FUNC_1)) {
- swfw = E1000_SWFW_PHY1_SM;
- } else {
- swfw = E1000_SWFW_PHY0_SM;
- }
+ swfw = E1000_SWFW_PHY0_SM;
if (e1000_swfw_sync_acquire(hw, swfw))
return -E1000_ERR_SWFW_SYNC;
- if ((hw->phy_type == e1000_phy_igp ||
- hw->phy_type == e1000_phy_igp_3 ||
- hw->phy_type == e1000_phy_igp_2) &&
- (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
+ if ((hw->phy_type == e1000_phy_igp) &&
+ (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
(u16)reg_addr);
if (ret_val) {
e1000_swfw_sync_release(hw, swfw);
return ret_val;
}
- } else if (hw->phy_type == e1000_phy_gg82563) {
- if (((reg_addr & MAX_PHY_REG_ADDRESS) > MAX_PHY_MULTI_PAGE_REG) ||
- (hw->mac_type == e1000_80003es2lan)) {
- /* Select Configuration Page */
- if ((reg_addr & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
- ret_val = e1000_write_phy_reg_ex(hw, GG82563_PHY_PAGE_SELECT,
- (u16)((u16)reg_addr >> GG82563_PAGE_SHIFT));
- } else {
- /* Use Alternative Page Select register to access
- * registers 30 and 31
- */
- ret_val = e1000_write_phy_reg_ex(hw,
- GG82563_PHY_PAGE_SELECT_ALT,
- (u16)((u16)reg_addr >> GG82563_PAGE_SHIFT));
- }
-
- if (ret_val) {
- e1000_swfw_sync_release(hw, swfw);
- return ret_val;
- }
- }
}
ret_val = e1000_read_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr,
DEBUGFUNC("e1000_write_phy_reg");
- if ((hw->mac_type == e1000_80003es2lan) &&
- (er32(STATUS) & E1000_STATUS_FUNC_1)) {
- swfw = E1000_SWFW_PHY1_SM;
- } else {
- swfw = E1000_SWFW_PHY0_SM;
- }
+ swfw = E1000_SWFW_PHY0_SM;
if (e1000_swfw_sync_acquire(hw, swfw))
return -E1000_ERR_SWFW_SYNC;
- if ((hw->phy_type == e1000_phy_igp ||
- hw->phy_type == e1000_phy_igp_3 ||
- hw->phy_type == e1000_phy_igp_2) &&
- (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
+ if ((hw->phy_type == e1000_phy_igp) &&
+ (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
(u16)reg_addr);
if (ret_val) {
e1000_swfw_sync_release(hw, swfw);
return ret_val;
}
- } else if (hw->phy_type == e1000_phy_gg82563) {
- if (((reg_addr & MAX_PHY_REG_ADDRESS) > MAX_PHY_MULTI_PAGE_REG) ||
- (hw->mac_type == e1000_80003es2lan)) {
- /* Select Configuration Page */
- if ((reg_addr & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
- ret_val = e1000_write_phy_reg_ex(hw, GG82563_PHY_PAGE_SELECT,
- (u16)((u16)reg_addr >> GG82563_PAGE_SHIFT));
- } else {
- /* Use Alternative Page Select register to access
- * registers 30 and 31
- */
- ret_val = e1000_write_phy_reg_ex(hw,
- GG82563_PHY_PAGE_SELECT_ALT,
- (u16)((u16)reg_addr >> GG82563_PAGE_SHIFT));
- }
-
- if (ret_val) {
- e1000_swfw_sync_release(hw, swfw);
- return ret_val;
- }
- }
}
ret_val = e1000_write_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr,
return E1000_SUCCESS;
}
-static s32 e1000_read_kmrn_reg(struct e1000_hw *hw, u32 reg_addr, u16 *data)
-{
- u32 reg_val;
- u16 swfw;
- DEBUGFUNC("e1000_read_kmrn_reg");
-
- if ((hw->mac_type == e1000_80003es2lan) &&
- (er32(STATUS) & E1000_STATUS_FUNC_1)) {
- swfw = E1000_SWFW_PHY1_SM;
- } else {
- swfw = E1000_SWFW_PHY0_SM;
- }
- if (e1000_swfw_sync_acquire(hw, swfw))
- return -E1000_ERR_SWFW_SYNC;
-
- /* Write register address */
- reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) &
- E1000_KUMCTRLSTA_OFFSET) |
- E1000_KUMCTRLSTA_REN;
- ew32(KUMCTRLSTA, reg_val);
- udelay(2);
-
- /* Read the data returned */
- reg_val = er32(KUMCTRLSTA);
- *data = (u16)reg_val;
-
- e1000_swfw_sync_release(hw, swfw);
- return E1000_SUCCESS;
-}
-
-static s32 e1000_write_kmrn_reg(struct e1000_hw *hw, u32 reg_addr, u16 data)
-{
- u32 reg_val;
- u16 swfw;
- DEBUGFUNC("e1000_write_kmrn_reg");
-
- if ((hw->mac_type == e1000_80003es2lan) &&
- (er32(STATUS) & E1000_STATUS_FUNC_1)) {
- swfw = E1000_SWFW_PHY1_SM;
- } else {
- swfw = E1000_SWFW_PHY0_SM;
- }
- if (e1000_swfw_sync_acquire(hw, swfw))
- return -E1000_ERR_SWFW_SYNC;
-
- reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) &
- E1000_KUMCTRLSTA_OFFSET) | data;
- ew32(KUMCTRLSTA, reg_val);
- udelay(2);
-
- e1000_swfw_sync_release(hw, swfw);
- return E1000_SUCCESS;
-}
-
/******************************************************************************
* Returns the PHY to the power-on reset state
*
DEBUGFUNC("e1000_phy_hw_reset");
- /* In the case of the phy reset being blocked, it's not an error, we
- * simply return success without performing the reset. */
- ret_val = e1000_check_phy_reset_block(hw);
- if (ret_val)
- return E1000_SUCCESS;
-
DEBUGOUT("Resetting Phy...\n");
if (hw->mac_type > e1000_82543) {
- if ((hw->mac_type == e1000_80003es2lan) &&
- (er32(STATUS) & E1000_STATUS_FUNC_1)) {
- swfw = E1000_SWFW_PHY1_SM;
- } else {
- swfw = E1000_SWFW_PHY0_SM;
- }
+ swfw = E1000_SWFW_PHY0_SM;
if (e1000_swfw_sync_acquire(hw, swfw)) {
DEBUGOUT("Unable to acquire swfw sync\n");
return -E1000_ERR_SWFW_SYNC;
}
/* Read the device control register and assert the E1000_CTRL_PHY_RST
* bit. Then, take it out of reset.
- * For pre-e1000_82571 hardware, we delay for 10ms between the assert
- * and deassert. For e1000_82571 hardware and later, we instead delay
- * for 50us between and 10ms after the deassertion.
+ * For e1000 hardware, we delay for 10ms between the assert
+ * and deassert.
*/
ctrl = er32(CTRL);
ew32(CTRL, ctrl | E1000_CTRL_PHY_RST);
E1000_WRITE_FLUSH();
- if (hw->mac_type < e1000_82571)
- msleep(10);
- else
- udelay(100);
+ msleep(10);
ew32(CTRL, ctrl);
E1000_WRITE_FLUSH();
- if (hw->mac_type >= e1000_82571)
- mdelay(10);
-
e1000_swfw_sync_release(hw, swfw);
} else {
/* Read the Extended Device Control Register, assert the PHY_RESET_DIR
ret_val = e1000_get_phy_cfg_done(hw);
if (ret_val != E1000_SUCCESS)
return ret_val;
- e1000_release_software_semaphore(hw);
-
- if ((hw->mac_type == e1000_ich8lan) && (hw->phy_type == e1000_phy_igp_3))
- ret_val = e1000_init_lcd_from_nvm(hw);
return ret_val;
}
DEBUGFUNC("e1000_phy_reset");
- /* In the case of the phy reset being blocked, it's not an error, we
- * simply return success without performing the reset. */
- ret_val = e1000_check_phy_reset_block(hw);
- if (ret_val)
- return E1000_SUCCESS;
-
switch (hw->phy_type) {
case e1000_phy_igp:
- case e1000_phy_igp_2:
- case e1000_phy_igp_3:
- case e1000_phy_ife:
ret_val = e1000_phy_hw_reset(hw);
if (ret_val)
return ret_val;
break;
}
- if (hw->phy_type == e1000_phy_igp || hw->phy_type == e1000_phy_igp_2)
+ if (hw->phy_type == e1000_phy_igp)
e1000_phy_init_script(hw);
return E1000_SUCCESS;
}
-/******************************************************************************
-* Work-around for 82566 power-down: on D3 entry-
-* 1) disable gigabit link
-* 2) write VR power-down enable
-* 3) read it back
-* if successful continue, else issue LCD reset and repeat
-*
-* hw - struct containing variables accessed by shared code
-******************************************************************************/
-void e1000_phy_powerdown_workaround(struct e1000_hw *hw)
-{
- s32 reg;
- u16 phy_data;
- s32 retry = 0;
-
- DEBUGFUNC("e1000_phy_powerdown_workaround");
-
- if (hw->phy_type != e1000_phy_igp_3)
- return;
-
- do {
- /* Disable link */
- reg = er32(PHY_CTRL);
- ew32(PHY_CTRL, reg | E1000_PHY_CTRL_GBE_DISABLE |
- E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
-
- /* Write VR power-down enable - bits 9:8 should be 10b */
- e1000_read_phy_reg(hw, IGP3_VR_CTRL, &phy_data);
- phy_data |= (1 << 9);
- phy_data &= ~(1 << 8);
- e1000_write_phy_reg(hw, IGP3_VR_CTRL, phy_data);
-
- /* Read it back and test */
- e1000_read_phy_reg(hw, IGP3_VR_CTRL, &phy_data);
- if (((phy_data & IGP3_VR_CTRL_MODE_MASK) == IGP3_VR_CTRL_MODE_SHUT) || retry)
- break;
-
- /* Issue PHY reset and repeat at most one more time */
- reg = er32(CTRL);
- ew32(CTRL, reg | E1000_CTRL_PHY_RST);
- retry++;
- } while (retry);
-
- return;
-
-}
-
-/******************************************************************************
-* Work-around for 82566 Kumeran PCS lock loss:
-* On link status change (i.e. PCI reset, speed change) and link is up and
-* speed is gigabit-
-* 0) if workaround is optionally disabled do nothing
-* 1) wait 1ms for Kumeran link to come up
-* 2) check Kumeran Diagnostic register PCS lock loss bit
-* 3) if not set the link is locked (all is good), otherwise...
-* 4) reset the PHY
-* 5) repeat up to 10 times
-* Note: this is only called for IGP3 copper when speed is 1gb.
-*
-* hw - struct containing variables accessed by shared code
-******************************************************************************/
-static s32 e1000_kumeran_lock_loss_workaround(struct e1000_hw *hw)
-{
- s32 ret_val;
- s32 reg;
- s32 cnt;
- u16 phy_data;
-
- if (hw->kmrn_lock_loss_workaround_disabled)
- return E1000_SUCCESS;
-
- /* Make sure link is up before proceeding. If not just return.
- * Attempting this while link is negotiating fouled up link
- * stability */
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
-
- if (phy_data & MII_SR_LINK_STATUS) {
- for (cnt = 0; cnt < 10; cnt++) {
- /* read once to clear */
- ret_val = e1000_read_phy_reg(hw, IGP3_KMRN_DIAG, &phy_data);
- if (ret_val)
- return ret_val;
- /* and again to get new status */
- ret_val = e1000_read_phy_reg(hw, IGP3_KMRN_DIAG, &phy_data);
- if (ret_val)
- return ret_val;
-
- /* check for PCS lock */
- if (!(phy_data & IGP3_KMRN_DIAG_PCS_LOCK_LOSS))
- return E1000_SUCCESS;
-
- /* Issue PHY reset */
- e1000_phy_hw_reset(hw);
- mdelay(5);
- }
- /* Disable GigE link negotiation */
- reg = er32(PHY_CTRL);
- ew32(PHY_CTRL, reg | E1000_PHY_CTRL_GBE_DISABLE |
- E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
-
- /* unable to acquire PCS lock */
- return E1000_ERR_PHY;
- }
-
- return E1000_SUCCESS;
-}
-
/******************************************************************************
* Probes the expected PHY address for known PHY IDs
*
if (hw->phy_id != 0)
return E1000_SUCCESS;
- /* The 82571 firmware may still be configuring the PHY. In this
- * case, we cannot access the PHY until the configuration is done. So
- * we explicitly set the PHY values. */
- if (hw->mac_type == e1000_82571 ||
- hw->mac_type == e1000_82572) {
- hw->phy_id = IGP01E1000_I_PHY_ID;
- hw->phy_type = e1000_phy_igp_2;
- return E1000_SUCCESS;
- }
-
- /* ESB-2 PHY reads require e1000_phy_gg82563 to be set because of a work-
- * around that forces PHY page 0 to be set or the reads fail. The rest of
- * the code in this routine uses e1000_read_phy_reg to read the PHY ID.
- * So for ESB-2 we need to have this set so our reads won't fail. If the
- * attached PHY is not a e1000_phy_gg82563, the routines below will figure
- * this out as well. */
- if (hw->mac_type == e1000_80003es2lan)
- hw->phy_type = e1000_phy_gg82563;
-
/* Read the PHY ID Registers to identify which PHY is onboard. */
ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high);
if (ret_val)
case e1000_82547_rev_2:
if (hw->phy_id == IGP01E1000_I_PHY_ID) match = true;
break;
- case e1000_82573:
- if (hw->phy_id == M88E1111_I_PHY_ID) match = true;
- break;
- case e1000_80003es2lan:
- if (hw->phy_id == GG82563_E_PHY_ID) match = true;
- break;
- case e1000_ich8lan:
- if (hw->phy_id == IGP03E1000_E_PHY_ID) match = true;
- if (hw->phy_id == IFE_E_PHY_ID) match = true;
- if (hw->phy_id == IFE_PLUS_E_PHY_ID) match = true;
- if (hw->phy_id == IFE_C_E_PHY_ID) match = true;
- break;
default:
DEBUGOUT1("Invalid MAC type %d\n", hw->mac_type);
return -E1000_ERR_CONFIG;
DEBUGFUNC("e1000_phy_reset_dsp");
do {
- if (hw->phy_type != e1000_phy_gg82563) {
- ret_val = e1000_write_phy_reg(hw, 29, 0x001d);
- if (ret_val) break;
- }
+ ret_val = e1000_write_phy_reg(hw, 29, 0x001d);
+ if (ret_val) break;
ret_val = e1000_write_phy_reg(hw, 30, 0x00c1);
if (ret_val) break;
ret_val = e1000_write_phy_reg(hw, 30, 0x0000);
return E1000_SUCCESS;
}
-/******************************************************************************
-* Get PHY information from various PHY registers for ife PHY only.
-*
-* hw - Struct containing variables accessed by shared code
-* phy_info - PHY information structure
-******************************************************************************/
-static s32 e1000_phy_ife_get_info(struct e1000_hw *hw,
- struct e1000_phy_info *phy_info)
-{
- s32 ret_val;
- u16 phy_data;
- e1000_rev_polarity polarity;
-
- DEBUGFUNC("e1000_phy_ife_get_info");
-
- phy_info->downshift = (e1000_downshift)hw->speed_downgraded;
- phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_normal;
-
- ret_val = e1000_read_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, &phy_data);
- if (ret_val)
- return ret_val;
- phy_info->polarity_correction =
- ((phy_data & IFE_PSC_AUTO_POLARITY_DISABLE) >>
- IFE_PSC_AUTO_POLARITY_DISABLE_SHIFT) ?
- e1000_polarity_reversal_disabled : e1000_polarity_reversal_enabled;
-
- if (phy_info->polarity_correction == e1000_polarity_reversal_enabled) {
- ret_val = e1000_check_polarity(hw, &polarity);
- if (ret_val)
- return ret_val;
- } else {
- /* Polarity is forced. */
- polarity = ((phy_data & IFE_PSC_FORCE_POLARITY) >>
- IFE_PSC_FORCE_POLARITY_SHIFT) ?
- e1000_rev_polarity_reversed : e1000_rev_polarity_normal;
- }
- phy_info->cable_polarity = polarity;
-
- ret_val = e1000_read_phy_reg(hw, IFE_PHY_MDIX_CONTROL, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_info->mdix_mode = (e1000_auto_x_mode)
- ((phy_data & (IFE_PMC_AUTO_MDIX | IFE_PMC_FORCE_MDIX)) >>
- IFE_PMC_MDIX_MODE_SHIFT);
-
- return E1000_SUCCESS;
-}
/******************************************************************************
* Get PHY information from various PHY registers fot m88 PHY only.
/* Cable Length Estimation and Local/Remote Receiver Information
* are only valid at 1000 Mbps.
*/
- if (hw->phy_type != e1000_phy_gg82563) {
- phy_info->cable_length = (e1000_cable_length)((phy_data & M88E1000_PSSR_CABLE_LENGTH) >>
- M88E1000_PSSR_CABLE_LENGTH_SHIFT);
- } else {
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_DSP_DISTANCE,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_info->cable_length = (e1000_cable_length)(phy_data & GG82563_DSPD_CABLE_LENGTH);
- }
+ phy_info->cable_length = (e1000_cable_length)((phy_data & M88E1000_PSSR_CABLE_LENGTH) >>
+ M88E1000_PSSR_CABLE_LENGTH_SHIFT);
ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data);
if (ret_val)
return -E1000_ERR_CONFIG;
}
- if (hw->phy_type == e1000_phy_igp ||
- hw->phy_type == e1000_phy_igp_3 ||
- hw->phy_type == e1000_phy_igp_2)
+ if (hw->phy_type == e1000_phy_igp)
return e1000_phy_igp_get_info(hw, phy_info);
- else if (hw->phy_type == e1000_phy_ife)
- return e1000_phy_ife_get_info(hw, phy_info);
else
return e1000_phy_m88_get_info(hw, phy_info);
}
/******************************************************************************
* Sets up eeprom variables in the hw struct. Must be called after mac_type
- * is configured. Additionally, if this is ICH8, the flash controller GbE
- * registers must be mapped, or this will crash.
+ * is configured.
*
* hw - Struct containing variables accessed by shared code
*****************************************************************************/
eeprom->use_eerd = false;
eeprom->use_eewr = false;
break;
- case e1000_82571:
- case e1000_82572:
- eeprom->type = e1000_eeprom_spi;
- eeprom->opcode_bits = 8;
- eeprom->delay_usec = 1;
- if (eecd & E1000_EECD_ADDR_BITS) {
- eeprom->page_size = 32;
- eeprom->address_bits = 16;
- } else {
- eeprom->page_size = 8;
- eeprom->address_bits = 8;
- }
- eeprom->use_eerd = false;
- eeprom->use_eewr = false;
- break;
- case e1000_82573:
- eeprom->type = e1000_eeprom_spi;
- eeprom->opcode_bits = 8;
- eeprom->delay_usec = 1;
- if (eecd & E1000_EECD_ADDR_BITS) {
- eeprom->page_size = 32;
- eeprom->address_bits = 16;
- } else {
- eeprom->page_size = 8;
- eeprom->address_bits = 8;
- }
- eeprom->use_eerd = true;
- eeprom->use_eewr = true;
- if (!e1000_is_onboard_nvm_eeprom(hw)) {
- eeprom->type = e1000_eeprom_flash;
- eeprom->word_size = 2048;
-
- /* Ensure that the Autonomous FLASH update bit is cleared due to
- * Flash update issue on parts which use a FLASH for NVM. */
- eecd &= ~E1000_EECD_AUPDEN;
- ew32(EECD, eecd);
- }
- break;
- case e1000_80003es2lan:
- eeprom->type = e1000_eeprom_spi;
- eeprom->opcode_bits = 8;
- eeprom->delay_usec = 1;
- if (eecd & E1000_EECD_ADDR_BITS) {
- eeprom->page_size = 32;
- eeprom->address_bits = 16;
- } else {
- eeprom->page_size = 8;
- eeprom->address_bits = 8;
- }
- eeprom->use_eerd = true;
- eeprom->use_eewr = false;
- break;
- case e1000_ich8lan:
- {
- s32 i = 0;
- u32 flash_size = E1000_READ_ICH_FLASH_REG(hw, ICH_FLASH_GFPREG);
-
- eeprom->type = e1000_eeprom_ich8;
- eeprom->use_eerd = false;
- eeprom->use_eewr = false;
- eeprom->word_size = E1000_SHADOW_RAM_WORDS;
-
- /* Zero the shadow RAM structure. But don't load it from NVM
- * so as to save time for driver init */
- if (hw->eeprom_shadow_ram != NULL) {
- for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) {
- hw->eeprom_shadow_ram[i].modified = false;
- hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF;
- }
- }
-
- hw->flash_base_addr = (flash_size & ICH_GFPREG_BASE_MASK) *
- ICH_FLASH_SECTOR_SIZE;
-
- hw->flash_bank_size = ((flash_size >> 16) & ICH_GFPREG_BASE_MASK) + 1;
- hw->flash_bank_size -= (flash_size & ICH_GFPREG_BASE_MASK);
-
- hw->flash_bank_size *= ICH_FLASH_SECTOR_SIZE;
-
- hw->flash_bank_size /= 2 * sizeof(u16);
-
- break;
- }
- default:
+ default:
break;
}
/* eeprom_size will be an enum [0..8] that maps to eeprom sizes 128B to
* 32KB (incremented by powers of 2).
*/
- if (hw->mac_type <= e1000_82547_rev_2) {
- /* Set to default value for initial eeprom read. */
- eeprom->word_size = 64;
- ret_val = e1000_read_eeprom(hw, EEPROM_CFG, 1, &eeprom_size);
- if (ret_val)
- return ret_val;
- eeprom_size = (eeprom_size & EEPROM_SIZE_MASK) >> EEPROM_SIZE_SHIFT;
- /* 256B eeprom size was not supported in earlier hardware, so we
- * bump eeprom_size up one to ensure that "1" (which maps to 256B)
- * is never the result used in the shifting logic below. */
- if (eeprom_size)
- eeprom_size++;
- } else {
- eeprom_size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
- E1000_EECD_SIZE_EX_SHIFT);
- }
+ /* Set to default value for initial eeprom read. */
+ eeprom->word_size = 64;
+ ret_val = e1000_read_eeprom(hw, EEPROM_CFG, 1, &eeprom_size);
+ if (ret_val)
+ return ret_val;
+ eeprom_size = (eeprom_size & EEPROM_SIZE_MASK) >> EEPROM_SIZE_SHIFT;
+ /* 256B eeprom size was not supported in earlier hardware, so we
+ * bump eeprom_size up one to ensure that "1" (which maps to 256B)
+ * is never the result used in the shifting logic below. */
+ if (eeprom_size)
+ eeprom_size++;
eeprom->word_size = 1 << (eeprom_size + EEPROM_WORD_SIZE_SHIFT);
}
return -E1000_ERR_SWFW_SYNC;
eecd = er32(EECD);
- if (hw->mac_type != e1000_82573) {
- /* Request EEPROM Access */
- if (hw->mac_type > e1000_82544) {
- eecd |= E1000_EECD_REQ;
- ew32(EECD, eecd);
+ /* Request EEPROM Access */
+ if (hw->mac_type > e1000_82544) {
+ eecd |= E1000_EECD_REQ;
+ ew32(EECD, eecd);
+ eecd = er32(EECD);
+ while ((!(eecd & E1000_EECD_GNT)) &&
+ (i < E1000_EEPROM_GRANT_ATTEMPTS)) {
+ i++;
+ udelay(5);
eecd = er32(EECD);
- while ((!(eecd & E1000_EECD_GNT)) &&
- (i < E1000_EEPROM_GRANT_ATTEMPTS)) {
- i++;
- udelay(5);
- eecd = er32(EECD);
- }
- if (!(eecd & E1000_EECD_GNT)) {
- eecd &= ~E1000_EECD_REQ;
- ew32(EECD, eecd);
- DEBUGOUT("Could not acquire EEPROM grant\n");
- e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM);
- return -E1000_ERR_EEPROM;
- }
+ }
+ if (!(eecd & E1000_EECD_GNT)) {
+ eecd &= ~E1000_EECD_REQ;
+ ew32(EECD, eecd);
+ DEBUGOUT("Could not acquire EEPROM grant\n");
+ e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM);
+ return -E1000_ERR_EEPROM;
}
}
* directly. In this case, we need to acquire the EEPROM so that
* FW or other port software does not interrupt.
*/
- if (e1000_is_onboard_nvm_eeprom(hw) && !hw->eeprom.use_eerd) {
+ if (!hw->eeprom.use_eerd) {
/* Prepare the EEPROM for bit-bang reading */
if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
return -E1000_ERR_EEPROM;
if (eeprom->use_eerd)
return e1000_read_eeprom_eerd(hw, offset, words, data);
- /* ICH EEPROM access is done via the ICH flash controller */
- if (eeprom->type == e1000_eeprom_ich8)
- return e1000_read_eeprom_ich8(hw, offset, words, data);
-
/* Set up the SPI or Microwire EEPROM for bit-bang reading. We have
* acquired the EEPROM at this point, so any returns should relase it */
if (eeprom->type == e1000_eeprom_spi) {
return done;
}
-/***************************************************************************
-* Description: Determines if the onboard NVM is FLASH or EEPROM.
-*
-* hw - Struct containing variables accessed by shared code
-****************************************************************************/
-static bool e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw)
-{
- u32 eecd = 0;
-
- DEBUGFUNC("e1000_is_onboard_nvm_eeprom");
-
- if (hw->mac_type == e1000_ich8lan)
- return false;
-
- if (hw->mac_type == e1000_82573) {
- eecd = er32(EECD);
-
- /* Isolate bits 15 & 16 */
- eecd = ((eecd >> 15) & 0x03);
-
- /* If both bits are set, device is Flash type */
- if (eecd == 0x03) {
- return false;
- }
- }
- return true;
-}
-
/******************************************************************************
* Verifies that the EEPROM has a valid checksum
*
DEBUGFUNC("e1000_validate_eeprom_checksum");
- if ((hw->mac_type == e1000_82573) && !e1000_is_onboard_nvm_eeprom(hw)) {
- /* Check bit 4 of word 10h. If it is 0, firmware is done updating
- * 10h-12h. Checksum may need to be fixed. */
- e1000_read_eeprom(hw, 0x10, 1, &eeprom_data);
- if ((eeprom_data & 0x10) == 0) {
- /* Read 0x23 and check bit 15. This bit is a 1 when the checksum
- * has already been fixed. If the checksum is still wrong and this
- * bit is a 1, we need to return bad checksum. Otherwise, we need
- * to set this bit to a 1 and update the checksum. */
- e1000_read_eeprom(hw, 0x23, 1, &eeprom_data);
- if ((eeprom_data & 0x8000) == 0) {
- eeprom_data |= 0x8000;
- e1000_write_eeprom(hw, 0x23, 1, &eeprom_data);
- e1000_update_eeprom_checksum(hw);
- }
- }
- }
-
- if (hw->mac_type == e1000_ich8lan) {
- /* Drivers must allocate the shadow ram structure for the
- * EEPROM checksum to be updated. Otherwise, this bit as well
- * as the checksum must both be set correctly for this
- * validation to pass.
- */
- e1000_read_eeprom(hw, 0x19, 1, &eeprom_data);
- if ((eeprom_data & 0x40) == 0) {
- eeprom_data |= 0x40;
- e1000_write_eeprom(hw, 0x19, 1, &eeprom_data);
- e1000_update_eeprom_checksum(hw);
- }
- }
-
for (i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) {
if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
DEBUGOUT("EEPROM Read Error\n");
*****************************************************************************/
s32 e1000_update_eeprom_checksum(struct e1000_hw *hw)
{
- u32 ctrl_ext;
u16 checksum = 0;
u16 i, eeprom_data;
if (e1000_write_eeprom(hw, EEPROM_CHECKSUM_REG, 1, &checksum) < 0) {
DEBUGOUT("EEPROM Write Error\n");
return -E1000_ERR_EEPROM;
- } else if (hw->eeprom.type == e1000_eeprom_flash) {
- e1000_commit_shadow_ram(hw);
- } else if (hw->eeprom.type == e1000_eeprom_ich8) {
- e1000_commit_shadow_ram(hw);
- /* Reload the EEPROM, or else modifications will not appear
- * until after next adapter reset. */
- ctrl_ext = er32(CTRL_EXT);
- ctrl_ext |= E1000_CTRL_EXT_EE_RST;
- ew32(CTRL_EXT, ctrl_ext);
- msleep(10);
}
return E1000_SUCCESS;
}
return -E1000_ERR_EEPROM;
}
- /* 82573 writes only through eewr */
if (eeprom->use_eewr)
return e1000_write_eeprom_eewr(hw, offset, words, data);
- if (eeprom->type == e1000_eeprom_ich8)
- return e1000_write_eeprom_ich8(hw, offset, words, data);
-
/* Prepare the EEPROM for writing */
if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
return -E1000_ERR_EEPROM;
return E1000_SUCCESS;
}
-/******************************************************************************
- * Flushes the cached eeprom to NVM. This is done by saving the modified values
- * in the eeprom cache and the non modified values in the currently active bank
- * to the new bank.
- *
- * hw - Struct containing variables accessed by shared code
- * offset - offset of word in the EEPROM to read
- * data - word read from the EEPROM
- * words - number of words to read
- *****************************************************************************/
-static s32 e1000_commit_shadow_ram(struct e1000_hw *hw)
-{
- u32 attempts = 100000;
- u32 eecd = 0;
- u32 flop = 0;
- u32 i = 0;
- s32 error = E1000_SUCCESS;
- u32 old_bank_offset = 0;
- u32 new_bank_offset = 0;
- u8 low_byte = 0;
- u8 high_byte = 0;
- bool sector_write_failed = false;
-
- if (hw->mac_type == e1000_82573) {
- /* The flop register will be used to determine if flash type is STM */
- flop = er32(FLOP);
- for (i=0; i < attempts; i++) {
- eecd = er32(EECD);
- if ((eecd & E1000_EECD_FLUPD) == 0) {
- break;
- }
- udelay(5);
- }
-
- if (i == attempts) {
- return -E1000_ERR_EEPROM;
- }
-
- /* If STM opcode located in bits 15:8 of flop, reset firmware */
- if ((flop & 0xFF00) == E1000_STM_OPCODE) {
- ew32(HICR, E1000_HICR_FW_RESET);
- }
-
- /* Perform the flash update */
- ew32(EECD, eecd | E1000_EECD_FLUPD);
-
- for (i=0; i < attempts; i++) {
- eecd = er32(EECD);
- if ((eecd & E1000_EECD_FLUPD) == 0) {
- break;
- }
- udelay(5);
- }
-
- if (i == attempts) {
- return -E1000_ERR_EEPROM;
- }
- }
-
- if (hw->mac_type == e1000_ich8lan && hw->eeprom_shadow_ram != NULL) {
- /* We're writing to the opposite bank so if we're on bank 1,
- * write to bank 0 etc. We also need to erase the segment that
- * is going to be written */
- if (!(er32(EECD) & E1000_EECD_SEC1VAL)) {
- new_bank_offset = hw->flash_bank_size * 2;
- old_bank_offset = 0;
- e1000_erase_ich8_4k_segment(hw, 1);
- } else {
- old_bank_offset = hw->flash_bank_size * 2;
- new_bank_offset = 0;
- e1000_erase_ich8_4k_segment(hw, 0);
- }
-
- sector_write_failed = false;
- /* Loop for every byte in the shadow RAM,
- * which is in units of words. */
- for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) {
- /* Determine whether to write the value stored
- * in the other NVM bank or a modified value stored
- * in the shadow RAM */
- if (hw->eeprom_shadow_ram[i].modified) {
- low_byte = (u8)hw->eeprom_shadow_ram[i].eeprom_word;
- udelay(100);
- error = e1000_verify_write_ich8_byte(hw,
- (i << 1) + new_bank_offset, low_byte);
-
- if (error != E1000_SUCCESS)
- sector_write_failed = true;
- else {
- high_byte =
- (u8)(hw->eeprom_shadow_ram[i].eeprom_word >> 8);
- udelay(100);
- }
- } else {
- e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset,
- &low_byte);
- udelay(100);
- error = e1000_verify_write_ich8_byte(hw,
- (i << 1) + new_bank_offset, low_byte);
-
- if (error != E1000_SUCCESS)
- sector_write_failed = true;
- else {
- e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset + 1,
- &high_byte);
- udelay(100);
- }
- }
-
- /* If the write of the low byte was successful, go ahead and
- * write the high byte while checking to make sure that if it
- * is the signature byte, then it is handled properly */
- if (!sector_write_failed) {
- /* If the word is 0x13, then make sure the signature bits
- * (15:14) are 11b until the commit has completed.
- * This will allow us to write 10b which indicates the
- * signature is valid. We want to do this after the write
- * has completed so that we don't mark the segment valid
- * while the write is still in progress */
- if (i == E1000_ICH_NVM_SIG_WORD)
- high_byte = E1000_ICH_NVM_SIG_MASK | high_byte;
-
- error = e1000_verify_write_ich8_byte(hw,
- (i << 1) + new_bank_offset + 1, high_byte);
- if (error != E1000_SUCCESS)
- sector_write_failed = true;
-
- } else {
- /* If the write failed then break from the loop and
- * return an error */
- break;
- }
- }
-
- /* Don't bother writing the segment valid bits if sector
- * programming failed. */
- if (!sector_write_failed) {
- /* Finally validate the new segment by setting bit 15:14
- * to 10b in word 0x13 , this can be done without an
- * erase as well since these bits are 11 to start with
- * and we need to change bit 14 to 0b */
- e1000_read_ich8_byte(hw,
- E1000_ICH_NVM_SIG_WORD * 2 + 1 + new_bank_offset,
- &high_byte);
- high_byte &= 0xBF;
- error = e1000_verify_write_ich8_byte(hw,
- E1000_ICH_NVM_SIG_WORD * 2 + 1 + new_bank_offset, high_byte);
- /* And invalidate the previously valid segment by setting
- * its signature word (0x13) high_byte to 0b. This can be
- * done without an erase because flash erase sets all bits
- * to 1's. We can write 1's to 0's without an erase */
- if (error == E1000_SUCCESS) {
- error = e1000_verify_write_ich8_byte(hw,
- E1000_ICH_NVM_SIG_WORD * 2 + 1 + old_bank_offset, 0);
- }
-
- /* Clear the now not used entry in the cache */
- for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) {
- hw->eeprom_shadow_ram[i].modified = false;
- hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF;
- }
- }
- }
-
- return error;
-}
-
/******************************************************************************
* Reads the adapter's MAC address from the EEPROM and inverts the LSB for the
* second function of dual function devices
break;
case e1000_82546:
case e1000_82546_rev_3:
- case e1000_82571:
- case e1000_80003es2lan:
if (er32(STATUS) & E1000_STATUS_FUNC_1)
hw->perm_mac_addr[5] ^= 0x01;
break;
rar_num = E1000_RAR_ENTRIES;
- /* Reserve a spot for the Locally Administered Address to work around
- * an 82571 issue in which a reset on one port will reload the MAC on
- * the other port. */
- if ((hw->mac_type == e1000_82571) && (hw->laa_is_present))
- rar_num -= 1;
- if (hw->mac_type == e1000_ich8lan)
- rar_num = E1000_RAR_ENTRIES_ICH8LAN;
-
/* Zero out the other 15 receive addresses. */
DEBUGOUT("Clearing RAR[1-15]\n");
for (i = 1; i < rar_num; i++) {
* LSB MSB
*/
case 0:
- if (hw->mac_type == e1000_ich8lan) {
- /* [47:38] i.e. 0x158 for above example address */
- hash_value = ((mc_addr[4] >> 6) | (((u16)mc_addr[5]) << 2));
- } else {
- /* [47:36] i.e. 0x563 for above example address */
- hash_value = ((mc_addr[4] >> 4) | (((u16)mc_addr[5]) << 4));
- }
+ /* [47:36] i.e. 0x563 for above example address */
+ hash_value = ((mc_addr[4] >> 4) | (((u16)mc_addr[5]) << 4));
break;
case 1:
- if (hw->mac_type == e1000_ich8lan) {
- /* [46:37] i.e. 0x2B1 for above example address */
- hash_value = ((mc_addr[4] >> 5) | (((u16)mc_addr[5]) << 3));
- } else {
- /* [46:35] i.e. 0xAC6 for above example address */
- hash_value = ((mc_addr[4] >> 3) | (((u16)mc_addr[5]) << 5));
- }
+ /* [46:35] i.e. 0xAC6 for above example address */
+ hash_value = ((mc_addr[4] >> 3) | (((u16)mc_addr[5]) << 5));
break;
case 2:
- if (hw->mac_type == e1000_ich8lan) {
- /*[45:36] i.e. 0x163 for above example address */
- hash_value = ((mc_addr[4] >> 4) | (((u16)mc_addr[5]) << 4));
- } else {
- /* [45:34] i.e. 0x5D8 for above example address */
- hash_value = ((mc_addr[4] >> 2) | (((u16)mc_addr[5]) << 6));
- }
+ /* [45:34] i.e. 0x5D8 for above example address */
+ hash_value = ((mc_addr[4] >> 2) | (((u16)mc_addr[5]) << 6));
break;
case 3:
- if (hw->mac_type == e1000_ich8lan) {
- /* [43:34] i.e. 0x18D for above example address */
- hash_value = ((mc_addr[4] >> 2) | (((u16)mc_addr[5]) << 6));
- } else {
- /* [43:32] i.e. 0x634 for above example address */
- hash_value = ((mc_addr[4]) | (((u16)mc_addr[5]) << 8));
- }
+ /* [43:32] i.e. 0x634 for above example address */
+ hash_value = ((mc_addr[4]) | (((u16)mc_addr[5]) << 8));
break;
}
hash_value &= 0xFFF;
- if (hw->mac_type == e1000_ich8lan)
- hash_value &= 0x3FF;
-
return hash_value;
}
* on our merry way.
*/
switch (hw->mac_type) {
- case e1000_82571:
- case e1000_82572:
- case e1000_80003es2lan:
- if (hw->leave_av_bit_off)
- break;
default:
/* Indicate to hardware the Address is Valid. */
rar_high |= E1000_RAH_AV;
{
u32 temp;
- if (hw->mac_type == e1000_ich8lan)
- return;
-
if ((hw->mac_type == e1000_82544) && ((offset & 0x1) == 1)) {
temp = E1000_READ_REG_ARRAY(hw, VFTA, (offset - 1));
E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value);
u32 vfta_offset = 0;
u32 vfta_bit_in_reg = 0;
- if (hw->mac_type == e1000_ich8lan)
- return;
-
- if (hw->mac_type == e1000_82573) {
- if (hw->mng_cookie.vlan_id != 0) {
- /* The VFTA is a 4096b bit-field, each identifying a single VLAN
- * ID. The following operations determine which 32b entry
- * (i.e. offset) into the array we want to set the VLAN ID
- * (i.e. bit) of the manageability unit. */
- vfta_offset = (hw->mng_cookie.vlan_id >>
- E1000_VFTA_ENTRY_SHIFT) &
- E1000_VFTA_ENTRY_MASK;
- vfta_bit_in_reg = 1 << (hw->mng_cookie.vlan_id &
- E1000_VFTA_ENTRY_BIT_SHIFT_MASK);
- }
- }
for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) {
/* If the offset we want to clear is the same offset of the
* manageability VLAN ID, then clear all bits except that of the
return -E1000_ERR_EEPROM;
}
- if ((hw->mac_type == e1000_82573) &&
- (eeprom_data == ID_LED_RESERVED_82573))
- eeprom_data = ID_LED_DEFAULT_82573;
- else if ((eeprom_data == ID_LED_RESERVED_0000) ||
+ if ((eeprom_data == ID_LED_RESERVED_0000) ||
(eeprom_data == ID_LED_RESERVED_FFFF)) {
- if (hw->mac_type == e1000_ich8lan)
- eeprom_data = ID_LED_DEFAULT_ICH8LAN;
- else
eeprom_data = ID_LED_DEFAULT;
}
return E1000_SUCCESS;
}
-
-/******************************************************************************
- * Used on 82571 and later Si that has LED blink bits.
- * Callers must use their own timer and should have already called
- * e1000_id_led_init()
- * Call e1000_cleanup led() to stop blinking
- *
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-s32 e1000_blink_led_start(struct e1000_hw *hw)
-{
- s16 i;
- u32 ledctl_blink = 0;
-
- DEBUGFUNC("e1000_id_led_blink_on");
-
- if (hw->mac_type < e1000_82571) {
- /* Nothing to do */
- return E1000_SUCCESS;
- }
- if (hw->media_type == e1000_media_type_fiber) {
- /* always blink LED0 for PCI-E fiber */
- ledctl_blink = E1000_LEDCTL_LED0_BLINK |
- (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED0_MODE_SHIFT);
- } else {
- /* set the blink bit for each LED that's "on" (0x0E) in ledctl_mode2 */
- ledctl_blink = hw->ledctl_mode2;
- for (i=0; i < 4; i++)
- if (((hw->ledctl_mode2 >> (i * 8)) & 0xFF) ==
- E1000_LEDCTL_MODE_LED_ON)
- ledctl_blink |= (E1000_LEDCTL_LED0_BLINK << (i * 8));
- }
-
- ew32(LEDCTL, ledctl_blink);
-
- return E1000_SUCCESS;
-}
-
/******************************************************************************
* Restores the saved state of the SW controlable LED.
*
return ret_val;
/* Fall Through */
default:
- if (hw->phy_type == e1000_phy_ife) {
- e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, 0);
- break;
- }
/* Restore LEDCTL settings */
ew32(LEDCTL, hw->ledctl_default);
break;
/* Clear SW Defineable Pin 0 to turn on the LED */
ctrl &= ~E1000_CTRL_SWDPIN0;
ctrl |= E1000_CTRL_SWDPIO0;
- } else if (hw->phy_type == e1000_phy_ife) {
- e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED,
- (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_ON));
} else if (hw->media_type == e1000_media_type_copper) {
ew32(LEDCTL, hw->ledctl_mode2);
return E1000_SUCCESS;
/* Set SW Defineable Pin 0 to turn off the LED */
ctrl |= E1000_CTRL_SWDPIN0;
ctrl |= E1000_CTRL_SWDPIO0;
- } else if (hw->phy_type == e1000_phy_ife) {
- e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED,
- (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_OFF));
} else if (hw->media_type == e1000_media_type_copper) {
ew32(LEDCTL, hw->ledctl_mode1);
return E1000_SUCCESS;
temp = er32(XOFFTXC);
temp = er32(FCRUC);
- if (hw->mac_type != e1000_ich8lan) {
temp = er32(PRC64);
temp = er32(PRC127);
temp = er32(PRC255);
temp = er32(PRC511);
temp = er32(PRC1023);
temp = er32(PRC1522);
- }
temp = er32(GPRC);
temp = er32(BPRC);
temp = er32(TPR);
temp = er32(TPT);
- if (hw->mac_type != e1000_ich8lan) {
temp = er32(PTC64);
temp = er32(PTC127);
temp = er32(PTC255);
temp = er32(PTC511);
temp = er32(PTC1023);
temp = er32(PTC1522);
- }
temp = er32(MPTC);
temp = er32(BPTC);
temp = er32(MGTPRC);
temp = er32(MGTPDC);
temp = er32(MGTPTC);
-
- if (hw->mac_type <= e1000_82547_rev_2) return;
-
- temp = er32(IAC);
- temp = er32(ICRXOC);
-
- if (hw->mac_type == e1000_ich8lan) return;
-
- temp = er32(ICRXPTC);
- temp = er32(ICRXATC);
- temp = er32(ICTXPTC);
- temp = er32(ICTXATC);
- temp = er32(ICTXQEC);
- temp = er32(ICTXQMTC);
- temp = er32(ICRXDMTC);
}
/******************************************************************************
*****************************************************************************/
void e1000_get_bus_info(struct e1000_hw *hw)
{
- s32 ret_val;
- u16 pci_ex_link_status;
u32 status;
switch (hw->mac_type) {
hw->bus_speed = e1000_bus_speed_unknown;
hw->bus_width = e1000_bus_width_unknown;
break;
- case e1000_82571:
- case e1000_82572:
- case e1000_82573:
- case e1000_80003es2lan:
- hw->bus_type = e1000_bus_type_pci_express;
- hw->bus_speed = e1000_bus_speed_2500;
- ret_val = e1000_read_pcie_cap_reg(hw,
- PCI_EX_LINK_STATUS,
- &pci_ex_link_status);
- if (ret_val)
- hw->bus_width = e1000_bus_width_unknown;
- else
- hw->bus_width = (pci_ex_link_status & PCI_EX_LINK_WIDTH_MASK) >>
- PCI_EX_LINK_WIDTH_SHIFT;
- break;
- case e1000_ich8lan:
- hw->bus_type = e1000_bus_type_pci_express;
- hw->bus_speed = e1000_bus_speed_2500;
- hw->bus_width = e1000_bus_width_pciex_1;
- break;
default:
status = er32(STATUS);
hw->bus_type = (status & E1000_STATUS_PCIX_MODE) ?
return -E1000_ERR_PHY;
break;
}
- } else if (hw->phy_type == e1000_phy_gg82563) {
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_DSP_DISTANCE,
- &phy_data);
- if (ret_val)
- return ret_val;
- cable_length = phy_data & GG82563_DSPD_CABLE_LENGTH;
-
- switch (cable_length) {
- case e1000_gg_cable_length_60:
- *min_length = 0;
- *max_length = e1000_igp_cable_length_60;
- break;
- case e1000_gg_cable_length_60_115:
- *min_length = e1000_igp_cable_length_60;
- *max_length = e1000_igp_cable_length_115;
- break;
- case e1000_gg_cable_length_115_150:
- *min_length = e1000_igp_cable_length_115;
- *max_length = e1000_igp_cable_length_150;
- break;
- case e1000_gg_cable_length_150:
- *min_length = e1000_igp_cable_length_150;
- *max_length = e1000_igp_cable_length_180;
- break;
- default:
- return -E1000_ERR_PHY;
- break;
- }
} else if (hw->phy_type == e1000_phy_igp) { /* For IGP PHY */
u16 cur_agc_value;
u16 min_agc_value = IGP01E1000_AGC_LENGTH_TABLE_SIZE;
IGP01E1000_AGC_RANGE) : 0;
*max_length = e1000_igp_cable_length_table[agc_value] +
IGP01E1000_AGC_RANGE;
- } else if (hw->phy_type == e1000_phy_igp_2 ||
- hw->phy_type == e1000_phy_igp_3) {
- u16 cur_agc_index, max_agc_index = 0;
- u16 min_agc_index = IGP02E1000_AGC_LENGTH_TABLE_SIZE - 1;
- u16 agc_reg_array[IGP02E1000_PHY_CHANNEL_NUM] =
- {IGP02E1000_PHY_AGC_A,
- IGP02E1000_PHY_AGC_B,
- IGP02E1000_PHY_AGC_C,
- IGP02E1000_PHY_AGC_D};
- /* Read the AGC registers for all channels */
- for (i = 0; i < IGP02E1000_PHY_CHANNEL_NUM; i++) {
- ret_val = e1000_read_phy_reg(hw, agc_reg_array[i], &phy_data);
- if (ret_val)
- return ret_val;
-
- /* Getting bits 15:9, which represent the combination of course and
- * fine gain values. The result is a number that can be put into
- * the lookup table to obtain the approximate cable length. */
- cur_agc_index = (phy_data >> IGP02E1000_AGC_LENGTH_SHIFT) &
- IGP02E1000_AGC_LENGTH_MASK;
-
- /* Array index bound check. */
- if ((cur_agc_index >= IGP02E1000_AGC_LENGTH_TABLE_SIZE) ||
- (cur_agc_index == 0))
- return -E1000_ERR_PHY;
-
- /* Remove min & max AGC values from calculation. */
- if (e1000_igp_2_cable_length_table[min_agc_index] >
- e1000_igp_2_cable_length_table[cur_agc_index])
- min_agc_index = cur_agc_index;
- if (e1000_igp_2_cable_length_table[max_agc_index] <
- e1000_igp_2_cable_length_table[cur_agc_index])
- max_agc_index = cur_agc_index;
-
- agc_value += e1000_igp_2_cable_length_table[cur_agc_index];
- }
-
- agc_value -= (e1000_igp_2_cable_length_table[min_agc_index] +
- e1000_igp_2_cable_length_table[max_agc_index]);
- agc_value /= (IGP02E1000_PHY_CHANNEL_NUM - 2);
-
- /* Calculate cable length with the error range of +/- 10 meters. */
- *min_length = ((agc_value - IGP02E1000_AGC_RANGE) > 0) ?
- (agc_value - IGP02E1000_AGC_RANGE) : 0;
- *max_length = agc_value + IGP02E1000_AGC_RANGE;
}
return E1000_SUCCESS;
DEBUGFUNC("e1000_check_polarity");
- if ((hw->phy_type == e1000_phy_m88) ||
- (hw->phy_type == e1000_phy_gg82563)) {
+ if (hw->phy_type == e1000_phy_m88) {
/* return the Polarity bit in the Status register. */
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
&phy_data);
M88E1000_PSSR_REV_POLARITY_SHIFT) ?
e1000_rev_polarity_reversed : e1000_rev_polarity_normal;
- } else if (hw->phy_type == e1000_phy_igp ||
- hw->phy_type == e1000_phy_igp_3 ||
- hw->phy_type == e1000_phy_igp_2) {
+ } else if (hw->phy_type == e1000_phy_igp) {
/* Read the Status register to check the speed */
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS,
&phy_data);
*polarity = (phy_data & IGP01E1000_PSSR_POLARITY_REVERSED) ?
e1000_rev_polarity_reversed : e1000_rev_polarity_normal;
}
- } else if (hw->phy_type == e1000_phy_ife) {
- ret_val = e1000_read_phy_reg(hw, IFE_PHY_EXTENDED_STATUS_CONTROL,
- &phy_data);
- if (ret_val)
- return ret_val;
- *polarity = ((phy_data & IFE_PESC_POLARITY_REVERSED) >>
- IFE_PESC_POLARITY_REVERSED_SHIFT) ?
- e1000_rev_polarity_reversed : e1000_rev_polarity_normal;
}
return E1000_SUCCESS;
}
DEBUGFUNC("e1000_check_downshift");
- if (hw->phy_type == e1000_phy_igp ||
- hw->phy_type == e1000_phy_igp_3 ||
- hw->phy_type == e1000_phy_igp_2) {
+ if (hw->phy_type == e1000_phy_igp) {
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_LINK_HEALTH,
&phy_data);
if (ret_val)
return ret_val;
hw->speed_downgraded = (phy_data & IGP01E1000_PLHR_SS_DOWNGRADE) ? 1 : 0;
- } else if ((hw->phy_type == e1000_phy_m88) ||
- (hw->phy_type == e1000_phy_gg82563)) {
+ } else if (hw->phy_type == e1000_phy_m88) {
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
&phy_data);
if (ret_val)
hw->speed_downgraded = (phy_data & M88E1000_PSSR_DOWNSHIFT) >>
M88E1000_PSSR_DOWNSHIFT_SHIFT;
- } else if (hw->phy_type == e1000_phy_ife) {
- /* e1000_phy_ife supports 10/100 speed only */
- hw->speed_downgraded = false;
}
return E1000_SUCCESS;
static s32 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active)
{
- u32 phy_ctrl = 0;
s32 ret_val;
u16 phy_data;
DEBUGFUNC("e1000_set_d3_lplu_state");
- if (hw->phy_type != e1000_phy_igp && hw->phy_type != e1000_phy_igp_2
- && hw->phy_type != e1000_phy_igp_3)
+ if (hw->phy_type != e1000_phy_igp)
return E1000_SUCCESS;
/* During driver activity LPLU should not be used or it will attain link
ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, &phy_data);
if (ret_val)
return ret_val;
- } else if (hw->mac_type == e1000_ich8lan) {
- /* MAC writes into PHY register based on the state transition
- * and start auto-negotiation. SW driver can overwrite the settings
- * in CSR PHY power control E1000_PHY_CTRL register. */
- phy_ctrl = er32(PHY_CTRL);
} else {
ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
if (ret_val)
if (ret_val)
return ret_val;
} else {
- if (hw->mac_type == e1000_ich8lan) {
- phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU;
- ew32(PHY_CTRL, phy_ctrl);
- } else {
- phy_data &= ~IGP02E1000_PM_D3_LPLU;
- ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
- phy_data);
- if (ret_val)
- return ret_val;
- }
+ phy_data &= ~IGP02E1000_PM_D3_LPLU;
+ ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
+ phy_data);
+ if (ret_val)
+ return ret_val;
}
/* LPLU and SmartSpeed are mutually exclusive. LPLU is used during
if (ret_val)
return ret_val;
} else {
- if (hw->mac_type == e1000_ich8lan) {
- phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU;
- ew32(PHY_CTRL, phy_ctrl);
- } else {
- phy_data |= IGP02E1000_PM_D3_LPLU;
- ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
- phy_data);
- if (ret_val)
- return ret_val;
- }
+ phy_data |= IGP02E1000_PM_D3_LPLU;
+ ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
+ phy_data);
+ if (ret_val)
+ return ret_val;
}
/* When LPLU is enabled we should disable SmartSpeed */
return E1000_SUCCESS;
}
-/*****************************************************************************
- *
- * This function sets the lplu d0 state according to the active flag. When
- * activating lplu this function also disables smart speed and vise versa.
- * lplu will not be activated unless the device autonegotiation advertisment
- * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes.
- * hw: Struct containing variables accessed by shared code
- * active - true to enable lplu false to disable lplu.
- *
- * returns: - E1000_ERR_PHY if fail to read/write the PHY
- * E1000_SUCCESS at any other case.
+/******************************************************************************
+ * Change VCO speed register to improve Bit Error Rate performance of SERDES.
*
- ****************************************************************************/
-
-static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active)
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+static s32 e1000_set_vco_speed(struct e1000_hw *hw)
{
- u32 phy_ctrl = 0;
- s32 ret_val;
+ s32 ret_val;
+ u16 default_page = 0;
u16 phy_data;
- DEBUGFUNC("e1000_set_d0_lplu_state");
- if (hw->mac_type <= e1000_82547_rev_2)
- return E1000_SUCCESS;
+ DEBUGFUNC("e1000_set_vco_speed");
- if (hw->mac_type == e1000_ich8lan) {
- phy_ctrl = er32(PHY_CTRL);
- } else {
- ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
- if (ret_val)
- return ret_val;
+ switch (hw->mac_type) {
+ case e1000_82545_rev_3:
+ case e1000_82546_rev_3:
+ break;
+ default:
+ return E1000_SUCCESS;
}
- if (!active) {
- if (hw->mac_type == e1000_ich8lan) {
- phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU;
- ew32(PHY_CTRL, phy_ctrl);
- } else {
- phy_data &= ~IGP02E1000_PM_D0_LPLU;
- ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data);
- if (ret_val)
- return ret_val;
- }
-
- /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during
- * Dx states where the power conservation is most important. During
- * driver activity we should enable SmartSpeed, so performance is
- * maintained. */
- if (hw->smart_speed == e1000_smart_speed_on) {
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data |= IGP01E1000_PSCFR_SMART_SPEED;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
- phy_data);
- if (ret_val)
- return ret_val;
- } else if (hw->smart_speed == e1000_smart_speed_off) {
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
- phy_data);
- if (ret_val)
- return ret_val;
- }
-
-
- } else {
-
- if (hw->mac_type == e1000_ich8lan) {
- phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU;
- ew32(PHY_CTRL, phy_ctrl);
- } else {
- phy_data |= IGP02E1000_PM_D0_LPLU;
- ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data);
- if (ret_val)
- return ret_val;
- }
-
- /* When LPLU is enabled we should disable SmartSpeed */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, phy_data);
- if (ret_val)
- return ret_val;
-
- }
- return E1000_SUCCESS;
-}
-
-/******************************************************************************
- * Change VCO speed register to improve Bit Error Rate performance of SERDES.
- *
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-static s32 e1000_set_vco_speed(struct e1000_hw *hw)
-{
- s32 ret_val;
- u16 default_page = 0;
- u16 phy_data;
-
- DEBUGFUNC("e1000_set_vco_speed");
-
- switch (hw->mac_type) {
- case e1000_82545_rev_3:
- case e1000_82546_rev_3:
- break;
- default:
- return E1000_SUCCESS;
- }
-
- /* Set PHY register 30, page 5, bit 8 to 0 */
+ /* Set PHY register 30, page 5, bit 8 to 0 */
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, &default_page);
if (ret_val)
}
-/*****************************************************************************
- * This function reads the cookie from ARC ram.
- *
- * returns: - E1000_SUCCESS .
- ****************************************************************************/
-static s32 e1000_host_if_read_cookie(struct e1000_hw *hw, u8 *buffer)
-{
- u8 i;
- u32 offset = E1000_MNG_DHCP_COOKIE_OFFSET;
- u8 length = E1000_MNG_DHCP_COOKIE_LENGTH;
-
- length = (length >> 2);
- offset = (offset >> 2);
-
- for (i = 0; i < length; i++) {
- *((u32 *)buffer + i) =
- E1000_READ_REG_ARRAY_DWORD(hw, HOST_IF, offset + i);
- }
- return E1000_SUCCESS;
-}
-
-
-/*****************************************************************************
- * This function checks whether the HOST IF is enabled for command operaton
- * and also checks whether the previous command is completed.
- * It busy waits in case of previous command is not completed.
- *
- * returns: - E1000_ERR_HOST_INTERFACE_COMMAND in case if is not ready or
- * timeout
- * - E1000_SUCCESS for success.
- ****************************************************************************/
-static s32 e1000_mng_enable_host_if(struct e1000_hw *hw)
-{
- u32 hicr;
- u8 i;
-
- /* Check that the host interface is enabled. */
- hicr = er32(HICR);
- if ((hicr & E1000_HICR_EN) == 0) {
- DEBUGOUT("E1000_HOST_EN bit disabled.\n");
- return -E1000_ERR_HOST_INTERFACE_COMMAND;
- }
- /* check the previous command is completed */
- for (i = 0; i < E1000_MNG_DHCP_COMMAND_TIMEOUT; i++) {
- hicr = er32(HICR);
- if (!(hicr & E1000_HICR_C))
- break;
- mdelay(1);
- }
-
- if (i == E1000_MNG_DHCP_COMMAND_TIMEOUT) {
- DEBUGOUT("Previous command timeout failed .\n");
- return -E1000_ERR_HOST_INTERFACE_COMMAND;
- }
- return E1000_SUCCESS;
-}
-
-/*****************************************************************************
- * This function writes the buffer content at the offset given on the host if.
- * It also does alignment considerations to do the writes in most efficient way.
- * Also fills up the sum of the buffer in *buffer parameter.
- *
- * returns - E1000_SUCCESS for success.
- ****************************************************************************/
-static s32 e1000_mng_host_if_write(struct e1000_hw *hw, u8 *buffer, u16 length,
- u16 offset, u8 *sum)
-{
- u8 *tmp;
- u8 *bufptr = buffer;
- u32 data = 0;
- u16 remaining, i, j, prev_bytes;
-
- /* sum = only sum of the data and it is not checksum */
-
- if (length == 0 || offset + length > E1000_HI_MAX_MNG_DATA_LENGTH) {
- return -E1000_ERR_PARAM;
- }
-
- tmp = (u8 *)&data;
- prev_bytes = offset & 0x3;
- offset &= 0xFFFC;
- offset >>= 2;
-
- if (prev_bytes) {
- data = E1000_READ_REG_ARRAY_DWORD(hw, HOST_IF, offset);
- for (j = prev_bytes; j < sizeof(u32); j++) {
- *(tmp + j) = *bufptr++;
- *sum += *(tmp + j);
- }
- E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset, data);
- length -= j - prev_bytes;
- offset++;
- }
-
- remaining = length & 0x3;
- length -= remaining;
-
- /* Calculate length in DWORDs */
- length >>= 2;
-
- /* The device driver writes the relevant command block into the
- * ram area. */
- for (i = 0; i < length; i++) {
- for (j = 0; j < sizeof(u32); j++) {
- *(tmp + j) = *bufptr++;
- *sum += *(tmp + j);
- }
-
- E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset + i, data);
- }
- if (remaining) {
- for (j = 0; j < sizeof(u32); j++) {
- if (j < remaining)
- *(tmp + j) = *bufptr++;
- else
- *(tmp + j) = 0;
-
- *sum += *(tmp + j);
- }
- E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset + i, data);
- }
-
- return E1000_SUCCESS;
-}
-
-
-/*****************************************************************************
- * This function writes the command header after does the checksum calculation.
- *
- * returns - E1000_SUCCESS for success.
- ****************************************************************************/
-static s32 e1000_mng_write_cmd_header(struct e1000_hw *hw,
- struct e1000_host_mng_command_header *hdr)
-{
- u16 i;
- u8 sum;
- u8 *buffer;
-
- /* Write the whole command header structure which includes sum of
- * the buffer */
-
- u16 length = sizeof(struct e1000_host_mng_command_header);
-
- sum = hdr->checksum;
- hdr->checksum = 0;
-
- buffer = (u8 *)hdr;
- i = length;
- while (i--)
- sum += buffer[i];
-
- hdr->checksum = 0 - sum;
-
- length >>= 2;
- /* The device driver writes the relevant command block into the ram area. */
- for (i = 0; i < length; i++) {
- E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, i, *((u32 *)hdr + i));
- E1000_WRITE_FLUSH();
- }
-
- return E1000_SUCCESS;
-}
-
-
-/*****************************************************************************
- * This function indicates to ARC that a new command is pending which completes
- * one write operation by the driver.
- *
- * returns - E1000_SUCCESS for success.
- ****************************************************************************/
-static s32 e1000_mng_write_commit(struct e1000_hw *hw)
-{
- u32 hicr;
-
- hicr = er32(HICR);
- /* Setting this bit tells the ARC that a new command is pending. */
- ew32(HICR, hicr | E1000_HICR_C);
-
- return E1000_SUCCESS;
-}
-
-
-/*****************************************************************************
- * This function checks the mode of the firmware.
- *
- * returns - true when the mode is IAMT or false.
- ****************************************************************************/
-bool e1000_check_mng_mode(struct e1000_hw *hw)
-{
- u32 fwsm;
-
- fwsm = er32(FWSM);
-
- if (hw->mac_type == e1000_ich8lan) {
- if ((fwsm & E1000_FWSM_MODE_MASK) ==
- (E1000_MNG_ICH_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
- return true;
- } else if ((fwsm & E1000_FWSM_MODE_MASK) ==
- (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
- return true;
-
- return false;
-}
-
-
-/*****************************************************************************
- * This function writes the dhcp info .
- ****************************************************************************/
-s32 e1000_mng_write_dhcp_info(struct e1000_hw *hw, u8 *buffer, u16 length)
-{
- s32 ret_val;
- struct e1000_host_mng_command_header hdr;
-
- hdr.command_id = E1000_MNG_DHCP_TX_PAYLOAD_CMD;
- hdr.command_length = length;
- hdr.reserved1 = 0;
- hdr.reserved2 = 0;
- hdr.checksum = 0;
-
- ret_val = e1000_mng_enable_host_if(hw);
- if (ret_val == E1000_SUCCESS) {
- ret_val = e1000_mng_host_if_write(hw, buffer, length, sizeof(hdr),
- &(hdr.checksum));
- if (ret_val == E1000_SUCCESS) {
- ret_val = e1000_mng_write_cmd_header(hw, &hdr);
- if (ret_val == E1000_SUCCESS)
- ret_val = e1000_mng_write_commit(hw);
- }
- }
- return ret_val;
-}
-
-
-/*****************************************************************************
- * This function calculates the checksum.
- *
- * returns - checksum of buffer contents.
- ****************************************************************************/
-static u8 e1000_calculate_mng_checksum(char *buffer, u32 length)
-{
- u8 sum = 0;
- u32 i;
-
- if (!buffer)
- return 0;
-
- for (i=0; i < length; i++)
- sum += buffer[i];
-
- return (u8)(0 - sum);
-}
-
-/*****************************************************************************
- * This function checks whether tx pkt filtering needs to be enabled or not.
- *
- * returns - true for packet filtering or false.
- ****************************************************************************/
-bool e1000_enable_tx_pkt_filtering(struct e1000_hw *hw)
-{
- /* called in init as well as watchdog timer functions */
-
- s32 ret_val, checksum;
- bool tx_filter = false;
- struct e1000_host_mng_dhcp_cookie *hdr = &(hw->mng_cookie);
- u8 *buffer = (u8 *) &(hw->mng_cookie);
-
- if (e1000_check_mng_mode(hw)) {
- ret_val = e1000_mng_enable_host_if(hw);
- if (ret_val == E1000_SUCCESS) {
- ret_val = e1000_host_if_read_cookie(hw, buffer);
- if (ret_val == E1000_SUCCESS) {
- checksum = hdr->checksum;
- hdr->checksum = 0;
- if ((hdr->signature == E1000_IAMT_SIGNATURE) &&
- checksum == e1000_calculate_mng_checksum((char *)buffer,
- E1000_MNG_DHCP_COOKIE_LENGTH)) {
- if (hdr->status &
- E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT)
- tx_filter = true;
- } else
- tx_filter = true;
- } else
- tx_filter = true;
- }
- }
-
- hw->tx_pkt_filtering = tx_filter;
- return tx_filter;
-}
-
/******************************************************************************
* Verifies the hardware needs to allow ARPs to be processed by the host
*
u32 e1000_enable_mng_pass_thru(struct e1000_hw *hw)
{
u32 manc;
- u32 fwsm, factps;
if (hw->asf_firmware_present) {
manc = er32(MANC);
if (!(manc & E1000_MANC_RCV_TCO_EN) ||
!(manc & E1000_MANC_EN_MAC_ADDR_FILTER))
return false;
- if (e1000_arc_subsystem_valid(hw)) {
- fwsm = er32(FWSM);
- factps = er32(FACTPS);
-
- if ((((fwsm & E1000_FWSM_MODE_MASK) >> E1000_FWSM_MODE_SHIFT) ==
- e1000_mng_mode_pt) && !(factps & E1000_FACTPS_MNGCG))
- return true;
- } else
- if ((manc & E1000_MANC_SMBUS_EN) && !(manc & E1000_MANC_ASF_EN))
- return true;
+ if ((manc & E1000_MANC_SMBUS_EN) && !(manc & E1000_MANC_ASF_EN))
+ return true;
}
return false;
}
return E1000_SUCCESS;
}
-/***************************************************************************
+/*******************************************************************************
*
- * Disables PCI-Express master access.
+ * Check for EEPROM Auto Read bit done.
*
* hw: Struct containing variables accessed by shared code
*
- * returns: - none.
+ * returns: - E1000_ERR_RESET if fail to reset MAC
+ * E1000_SUCCESS at any other case.
*
- ***************************************************************************/
-static void e1000_set_pci_express_master_disable(struct e1000_hw *hw)
+ ******************************************************************************/
+static s32 e1000_get_auto_rd_done(struct e1000_hw *hw)
{
- u32 ctrl;
-
- DEBUGFUNC("e1000_set_pci_express_master_disable");
-
- if (hw->bus_type != e1000_bus_type_pci_express)
- return;
+ DEBUGFUNC("e1000_get_auto_rd_done");
+ msleep(5);
+ return E1000_SUCCESS;
+}
- ctrl = er32(CTRL);
- ctrl |= E1000_CTRL_GIO_MASTER_DISABLE;
- ew32(CTRL, ctrl);
+/***************************************************************************
+ * Checks if the PHY configuration is done
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ * returns: - E1000_ERR_RESET if fail to reset MAC
+ * E1000_SUCCESS at any other case.
+ *
+ ***************************************************************************/
+static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_get_phy_cfg_done");
+ mdelay(10);
+ return E1000_SUCCESS;
}
-/*******************************************************************************
+/***************************************************************************
*
- * Disables PCI-Express master access and verifies there are no pending requests
+ * Using the combination of SMBI and SWESMBI semaphore bits when resetting
+ * adapter or Eeprom access.
*
* hw: Struct containing variables accessed by shared code
*
- * returns: - E1000_ERR_MASTER_REQUESTS_PENDING if master disable bit hasn't
- * caused the master requests to be disabled.
- * E1000_SUCCESS master requests disabled.
+ * returns: - E1000_ERR_EEPROM if fail to access EEPROM.
+ * E1000_SUCCESS at any other case.
*
- ******************************************************************************/
-s32 e1000_disable_pciex_master(struct e1000_hw *hw)
+ ***************************************************************************/
+static s32 e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw)
{
- s32 timeout = MASTER_DISABLE_TIMEOUT; /* 80ms */
+ s32 timeout;
+ u32 swsm;
- DEBUGFUNC("e1000_disable_pciex_master");
+ DEBUGFUNC("e1000_get_hw_eeprom_semaphore");
- if (hw->bus_type != e1000_bus_type_pci_express)
+ if (!hw->eeprom_semaphore_present)
return E1000_SUCCESS;
- e1000_set_pci_express_master_disable(hw);
-
+ /* Get the FW semaphore. */
+ timeout = hw->eeprom.word_size + 1;
while (timeout) {
- if (!(er32(STATUS) & E1000_STATUS_GIO_MASTER_ENABLE))
+ swsm = er32(SWSM);
+ swsm |= E1000_SWSM_SWESMBI;
+ ew32(SWSM, swsm);
+ /* if we managed to set the bit we got the semaphore. */
+ swsm = er32(SWSM);
+ if (swsm & E1000_SWSM_SWESMBI)
break;
- else
- udelay(100);
+
+ udelay(50);
timeout--;
}
if (!timeout) {
- DEBUGOUT("Master requests are pending.\n");
- return -E1000_ERR_MASTER_REQUESTS_PENDING;
- }
-
- return E1000_SUCCESS;
-}
-
-/*******************************************************************************
- *
- * Check for EEPROM Auto Read bit done.
- *
- * hw: Struct containing variables accessed by shared code
- *
- * returns: - E1000_ERR_RESET if fail to reset MAC
- * E1000_SUCCESS at any other case.
- *
- ******************************************************************************/
-static s32 e1000_get_auto_rd_done(struct e1000_hw *hw)
-{
- s32 timeout = AUTO_READ_DONE_TIMEOUT;
-
- DEBUGFUNC("e1000_get_auto_rd_done");
-
- switch (hw->mac_type) {
- default:
- msleep(5);
- break;
- case e1000_82571:
- case e1000_82572:
- case e1000_82573:
- case e1000_80003es2lan:
- case e1000_ich8lan:
- while (timeout) {
- if (er32(EECD) & E1000_EECD_AUTO_RD)
- break;
- else msleep(1);
- timeout--;
- }
-
- if (!timeout) {
- DEBUGOUT("Auto read by HW from EEPROM has not completed.\n");
- return -E1000_ERR_RESET;
- }
- break;
- }
-
- /* PHY configuration from NVM just starts after EECD_AUTO_RD sets to high.
- * Need to wait for PHY configuration completion before accessing NVM
- * and PHY. */
- if (hw->mac_type == e1000_82573)
- msleep(25);
-
- return E1000_SUCCESS;
-}
-
-/***************************************************************************
- * Checks if the PHY configuration is done
- *
- * hw: Struct containing variables accessed by shared code
- *
- * returns: - E1000_ERR_RESET if fail to reset MAC
- * E1000_SUCCESS at any other case.
- *
- ***************************************************************************/
-static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw)
-{
- s32 timeout = PHY_CFG_TIMEOUT;
- u32 cfg_mask = E1000_EEPROM_CFG_DONE;
-
- DEBUGFUNC("e1000_get_phy_cfg_done");
-
- switch (hw->mac_type) {
- default:
- mdelay(10);
- break;
- case e1000_80003es2lan:
- /* Separate *_CFG_DONE_* bit for each port */
- if (er32(STATUS) & E1000_STATUS_FUNC_1)
- cfg_mask = E1000_EEPROM_CFG_DONE_PORT_1;
- /* Fall Through */
- case e1000_82571:
- case e1000_82572:
- while (timeout) {
- if (er32(EEMNGCTL) & cfg_mask)
- break;
- else
- msleep(1);
- timeout--;
- }
- if (!timeout) {
- DEBUGOUT("MNG configuration cycle has not completed.\n");
- return -E1000_ERR_RESET;
- }
- break;
- }
-
- return E1000_SUCCESS;
-}
-
-/***************************************************************************
- *
- * Using the combination of SMBI and SWESMBI semaphore bits when resetting
- * adapter or Eeprom access.
- *
- * hw: Struct containing variables accessed by shared code
- *
- * returns: - E1000_ERR_EEPROM if fail to access EEPROM.
- * E1000_SUCCESS at any other case.
- *
- ***************************************************************************/
-static s32 e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw)
-{
- s32 timeout;
- u32 swsm;
-
- DEBUGFUNC("e1000_get_hw_eeprom_semaphore");
-
- if (!hw->eeprom_semaphore_present)
- return E1000_SUCCESS;
-
- if (hw->mac_type == e1000_80003es2lan) {
- /* Get the SW semaphore. */
- if (e1000_get_software_semaphore(hw) != E1000_SUCCESS)
- return -E1000_ERR_EEPROM;
- }
-
- /* Get the FW semaphore. */
- timeout = hw->eeprom.word_size + 1;
- while (timeout) {
- swsm = er32(SWSM);
- swsm |= E1000_SWSM_SWESMBI;
- ew32(SWSM, swsm);
- /* if we managed to set the bit we got the semaphore. */
- swsm = er32(SWSM);
- if (swsm & E1000_SWSM_SWESMBI)
- break;
-
- udelay(50);
- timeout--;
- }
-
- if (!timeout) {
- /* Release semaphores */
- e1000_put_hw_eeprom_semaphore(hw);
- DEBUGOUT("Driver can't access the Eeprom - SWESMBI bit is set.\n");
- return -E1000_ERR_EEPROM;
+ /* Release semaphores */
+ e1000_put_hw_eeprom_semaphore(hw);
+ DEBUGOUT("Driver can't access the Eeprom - SWESMBI bit is set.\n");
+ return -E1000_ERR_EEPROM;
}
return E1000_SUCCESS;
return;
swsm = er32(SWSM);
- if (hw->mac_type == e1000_80003es2lan) {
- /* Release both semaphores. */
- swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI);
- } else
- swsm &= ~(E1000_SWSM_SWESMBI);
+ swsm &= ~(E1000_SWSM_SWESMBI);
ew32(SWSM, swsm);
}
-
-/***************************************************************************
- *
- * Obtaining software semaphore bit (SMBI) before resetting PHY.
- *
- * hw: Struct containing variables accessed by shared code
- *
- * returns: - E1000_ERR_RESET if fail to obtain semaphore.
- * E1000_SUCCESS at any other case.
- *
- ***************************************************************************/
-static s32 e1000_get_software_semaphore(struct e1000_hw *hw)
-{
- s32 timeout = hw->eeprom.word_size + 1;
- u32 swsm;
-
- DEBUGFUNC("e1000_get_software_semaphore");
-
- if (hw->mac_type != e1000_80003es2lan) {
- return E1000_SUCCESS;
- }
-
- while (timeout) {
- swsm = er32(SWSM);
- /* If SMBI bit cleared, it is now set and we hold the semaphore */
- if (!(swsm & E1000_SWSM_SMBI))
- break;
- mdelay(1);
- timeout--;
- }
-
- if (!timeout) {
- DEBUGOUT("Driver can't access device - SMBI bit is set.\n");
- return -E1000_ERR_RESET;
- }
-
- return E1000_SUCCESS;
-}
-
-/***************************************************************************
- *
- * Release semaphore bit (SMBI).
- *
- * hw: Struct containing variables accessed by shared code
- *
- ***************************************************************************/
-static void e1000_release_software_semaphore(struct e1000_hw *hw)
-{
- u32 swsm;
-
- DEBUGFUNC("e1000_release_software_semaphore");
-
- if (hw->mac_type != e1000_80003es2lan) {
- return;
- }
-
- swsm = er32(SWSM);
- /* Release the SW semaphores.*/
- swsm &= ~E1000_SWSM_SMBI;
- ew32(SWSM, swsm);
-}
-
-/******************************************************************************
- * Checks if PHY reset is blocked due to SOL/IDER session, for example.
- * Returning E1000_BLK_PHY_RESET isn't necessarily an error. But it's up to
- * the caller to figure out how to deal with it.
- *
- * hw - Struct containing variables accessed by shared code
- *
- * returns: - E1000_BLK_PHY_RESET
- * E1000_SUCCESS
- *
- *****************************************************************************/
-s32 e1000_check_phy_reset_block(struct e1000_hw *hw)
-{
- u32 manc = 0;
- u32 fwsm = 0;
-
- if (hw->mac_type == e1000_ich8lan) {
- fwsm = er32(FWSM);
- return (fwsm & E1000_FWSM_RSPCIPHY) ? E1000_SUCCESS
- : E1000_BLK_PHY_RESET;
- }
-
- if (hw->mac_type > e1000_82547_rev_2)
- manc = er32(MANC);
- return (manc & E1000_MANC_BLK_PHY_RST_ON_IDE) ?
- E1000_BLK_PHY_RESET : E1000_SUCCESS;
-}
-
-static u8 e1000_arc_subsystem_valid(struct e1000_hw *hw)
-{
- u32 fwsm;
-
- /* On 8257x silicon, registers in the range of 0x8800 - 0x8FFC
- * may not be provided a DMA clock when no manageability features are
- * enabled. We do not want to perform any reads/writes to these registers
- * if this is the case. We read FWSM to determine the manageability mode.
- */
- switch (hw->mac_type) {
- case e1000_82571:
- case e1000_82572:
- case e1000_82573:
- case e1000_80003es2lan:
- fwsm = er32(FWSM);
- if ((fwsm & E1000_FWSM_MODE_MASK) != 0)
- return true;
- break;
- case e1000_ich8lan:
- return true;
- default:
- break;
- }
- return false;
-}
-
-
-/******************************************************************************
- * Configure PCI-Ex no-snoop
- *
- * hw - Struct containing variables accessed by shared code.
- * no_snoop - Bitmap of no-snoop events.
- *
- * returns: E1000_SUCCESS
- *
- *****************************************************************************/
-static s32 e1000_set_pci_ex_no_snoop(struct e1000_hw *hw, u32 no_snoop)
-{
- u32 gcr_reg = 0;
-
- DEBUGFUNC("e1000_set_pci_ex_no_snoop");
-
- if (hw->bus_type == e1000_bus_type_unknown)
- e1000_get_bus_info(hw);
-
- if (hw->bus_type != e1000_bus_type_pci_express)
- return E1000_SUCCESS;
-
- if (no_snoop) {
- gcr_reg = er32(GCR);
- gcr_reg &= ~(PCI_EX_NO_SNOOP_ALL);
- gcr_reg |= no_snoop;
- ew32(GCR, gcr_reg);
- }
- if (hw->mac_type == e1000_ich8lan) {
- u32 ctrl_ext;
-
- ew32(GCR, PCI_EX_82566_SNOOP_ALL);
-
- ctrl_ext = er32(CTRL_EXT);
- ctrl_ext |= E1000_CTRL_EXT_RO_DIS;
- ew32(CTRL_EXT, ctrl_ext);
- }
-
- return E1000_SUCCESS;
-}
-
-/***************************************************************************
- *
- * Get software semaphore FLAG bit (SWFLAG).
- * SWFLAG is used to synchronize the access to all shared resource between
- * SW, FW and HW.
- *
- * hw: Struct containing variables accessed by shared code
- *
- ***************************************************************************/
-static s32 e1000_get_software_flag(struct e1000_hw *hw)
-{
- s32 timeout = PHY_CFG_TIMEOUT;
- u32 extcnf_ctrl;
-
- DEBUGFUNC("e1000_get_software_flag");
-
- if (hw->mac_type == e1000_ich8lan) {
- while (timeout) {
- extcnf_ctrl = er32(EXTCNF_CTRL);
- extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG;
- ew32(EXTCNF_CTRL, extcnf_ctrl);
-
- extcnf_ctrl = er32(EXTCNF_CTRL);
- if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG)
- break;
- mdelay(1);
- timeout--;
- }
-
- if (!timeout) {
- DEBUGOUT("FW or HW locks the resource too long.\n");
- return -E1000_ERR_CONFIG;
- }
- }
-
- return E1000_SUCCESS;
-}
-
-/***************************************************************************
- *
- * Release software semaphore FLAG bit (SWFLAG).
- * SWFLAG is used to synchronize the access to all shared resource between
- * SW, FW and HW.
- *
- * hw: Struct containing variables accessed by shared code
- *
- ***************************************************************************/
-static void e1000_release_software_flag(struct e1000_hw *hw)
-{
- u32 extcnf_ctrl;
-
- DEBUGFUNC("e1000_release_software_flag");
-
- if (hw->mac_type == e1000_ich8lan) {
- extcnf_ctrl= er32(EXTCNF_CTRL);
- extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG;
- ew32(EXTCNF_CTRL, extcnf_ctrl);
- }
-
- return;
-}
-
-/******************************************************************************
- * Reads a 16 bit word or words from the EEPROM using the ICH8's flash access
- * register.
- *
- * hw - Struct containing variables accessed by shared code
- * offset - offset of word in the EEPROM to read
- * data - word read from the EEPROM
- * words - number of words to read
- *****************************************************************************/
-static s32 e1000_read_eeprom_ich8(struct e1000_hw *hw, u16 offset, u16 words,
- u16 *data)
-{
- s32 error = E1000_SUCCESS;
- u32 flash_bank = 0;
- u32 act_offset = 0;
- u32 bank_offset = 0;
- u16 word = 0;
- u16 i = 0;
-
- /* We need to know which is the valid flash bank. In the event
- * that we didn't allocate eeprom_shadow_ram, we may not be
- * managing flash_bank. So it cannot be trusted and needs
- * to be updated with each read.
- */
- /* Value of bit 22 corresponds to the flash bank we're on. */
- flash_bank = (er32(EECD) & E1000_EECD_SEC1VAL) ? 1 : 0;
-
- /* Adjust offset appropriately if we're on bank 1 - adjust for word size */
- bank_offset = flash_bank * (hw->flash_bank_size * 2);
-
- error = e1000_get_software_flag(hw);
- if (error != E1000_SUCCESS)
- return error;
-
- for (i = 0; i < words; i++) {
- if (hw->eeprom_shadow_ram != NULL &&
- hw->eeprom_shadow_ram[offset+i].modified) {
- data[i] = hw->eeprom_shadow_ram[offset+i].eeprom_word;
- } else {
- /* The NVM part needs a byte offset, hence * 2 */
- act_offset = bank_offset + ((offset + i) * 2);
- error = e1000_read_ich8_word(hw, act_offset, &word);
- if (error != E1000_SUCCESS)
- break;
- data[i] = word;
- }
- }
-
- e1000_release_software_flag(hw);
-
- return error;
-}
-
-/******************************************************************************
- * Writes a 16 bit word or words to the EEPROM using the ICH8's flash access
- * register. Actually, writes are written to the shadow ram cache in the hw
- * structure hw->e1000_shadow_ram. e1000_commit_shadow_ram flushes this to
- * the NVM, which occurs when the NVM checksum is updated.
- *
- * hw - Struct containing variables accessed by shared code
- * offset - offset of word in the EEPROM to write
- * words - number of words to write
- * data - words to write to the EEPROM
- *****************************************************************************/
-static s32 e1000_write_eeprom_ich8(struct e1000_hw *hw, u16 offset, u16 words,
- u16 *data)
-{
- u32 i = 0;
- s32 error = E1000_SUCCESS;
-
- error = e1000_get_software_flag(hw);
- if (error != E1000_SUCCESS)
- return error;
-
- /* A driver can write to the NVM only if it has eeprom_shadow_ram
- * allocated. Subsequent reads to the modified words are read from
- * this cached structure as well. Writes will only go into this
- * cached structure unless it's followed by a call to
- * e1000_update_eeprom_checksum() where it will commit the changes
- * and clear the "modified" field.
- */
- if (hw->eeprom_shadow_ram != NULL) {
- for (i = 0; i < words; i++) {
- if ((offset + i) < E1000_SHADOW_RAM_WORDS) {
- hw->eeprom_shadow_ram[offset+i].modified = true;
- hw->eeprom_shadow_ram[offset+i].eeprom_word = data[i];
- } else {
- error = -E1000_ERR_EEPROM;
- break;
- }
- }
- } else {
- /* Drivers have the option to not allocate eeprom_shadow_ram as long
- * as they don't perform any NVM writes. An attempt in doing so
- * will result in this error.
- */
- error = -E1000_ERR_EEPROM;
- }
-
- e1000_release_software_flag(hw);
-
- return error;
-}
-
-/******************************************************************************
- * This function does initial flash setup so that a new read/write/erase cycle
- * can be started.
- *
- * hw - The pointer to the hw structure
- ****************************************************************************/
-static s32 e1000_ich8_cycle_init(struct e1000_hw *hw)
-{
- union ich8_hws_flash_status hsfsts;
- s32 error = E1000_ERR_EEPROM;
- s32 i = 0;
-
- DEBUGFUNC("e1000_ich8_cycle_init");
-
- hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS);
-
- /* May be check the Flash Des Valid bit in Hw status */
- if (hsfsts.hsf_status.fldesvalid == 0) {
- DEBUGOUT("Flash descriptor invalid. SW Sequencing must be used.");
- return error;
- }
-
- /* Clear FCERR in Hw status by writing 1 */
- /* Clear DAEL in Hw status by writing a 1 */
- hsfsts.hsf_status.flcerr = 1;
- hsfsts.hsf_status.dael = 1;
-
- E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval);
-
- /* Either we should have a hardware SPI cycle in progress bit to check
- * against, in order to start a new cycle or FDONE bit should be changed
- * in the hardware so that it is 1 after harware reset, which can then be
- * used as an indication whether a cycle is in progress or has been
- * completed .. we should also have some software semaphore mechanism to
- * guard FDONE or the cycle in progress bit so that two threads access to
- * those bits can be sequentiallized or a way so that 2 threads dont
- * start the cycle at the same time */
-
- if (hsfsts.hsf_status.flcinprog == 0) {
- /* There is no cycle running at present, so we can start a cycle */
- /* Begin by setting Flash Cycle Done. */
- hsfsts.hsf_status.flcdone = 1;
- E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval);
- error = E1000_SUCCESS;
- } else {
- /* otherwise poll for sometime so the current cycle has a chance
- * to end before giving up. */
- for (i = 0; i < ICH_FLASH_COMMAND_TIMEOUT; i++) {
- hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS);
- if (hsfsts.hsf_status.flcinprog == 0) {
- error = E1000_SUCCESS;
- break;
- }
- udelay(1);
- }
- if (error == E1000_SUCCESS) {
- /* Successful in waiting for previous cycle to timeout,
- * now set the Flash Cycle Done. */
- hsfsts.hsf_status.flcdone = 1;
- E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval);
- } else {
- DEBUGOUT("Flash controller busy, cannot get access");
- }
- }
- return error;
-}
-
-/******************************************************************************
- * This function starts a flash cycle and waits for its completion
- *
- * hw - The pointer to the hw structure
- ****************************************************************************/
-static s32 e1000_ich8_flash_cycle(struct e1000_hw *hw, u32 timeout)
-{
- union ich8_hws_flash_ctrl hsflctl;
- union ich8_hws_flash_status hsfsts;
- s32 error = E1000_ERR_EEPROM;
- u32 i = 0;
-
- /* Start a cycle by writing 1 in Flash Cycle Go in Hw Flash Control */
- hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL);
- hsflctl.hsf_ctrl.flcgo = 1;
- E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval);
-
- /* wait till FDONE bit is set to 1 */
- do {
- hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS);
- if (hsfsts.hsf_status.flcdone == 1)
- break;
- udelay(1);
- i++;
- } while (i < timeout);
- if (hsfsts.hsf_status.flcdone == 1 && hsfsts.hsf_status.flcerr == 0) {
- error = E1000_SUCCESS;
- }
- return error;
-}
-
-/******************************************************************************
- * Reads a byte or word from the NVM using the ICH8 flash access registers.
- *
- * hw - The pointer to the hw structure
- * index - The index of the byte or word to read.
- * size - Size of data to read, 1=byte 2=word
- * data - Pointer to the word to store the value read.
- *****************************************************************************/
-static s32 e1000_read_ich8_data(struct e1000_hw *hw, u32 index, u32 size,
- u16 *data)
-{
- union ich8_hws_flash_status hsfsts;
- union ich8_hws_flash_ctrl hsflctl;
- u32 flash_linear_address;
- u32 flash_data = 0;
- s32 error = -E1000_ERR_EEPROM;
- s32 count = 0;
-
- DEBUGFUNC("e1000_read_ich8_data");
-
- if (size < 1 || size > 2 || data == NULL ||
- index > ICH_FLASH_LINEAR_ADDR_MASK)
- return error;
-
- flash_linear_address = (ICH_FLASH_LINEAR_ADDR_MASK & index) +
- hw->flash_base_addr;
-
- do {
- udelay(1);
- /* Steps */
- error = e1000_ich8_cycle_init(hw);
- if (error != E1000_SUCCESS)
- break;
-
- hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL);
- /* 0b/1b corresponds to 1 or 2 byte size, respectively. */
- hsflctl.hsf_ctrl.fldbcount = size - 1;
- hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_READ;
- E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval);
-
- /* Write the last 24 bits of index into Flash Linear address field in
- * Flash Address */
- /* TODO: TBD maybe check the index against the size of flash */
-
- E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_address);
-
- error = e1000_ich8_flash_cycle(hw, ICH_FLASH_COMMAND_TIMEOUT);
-
- /* Check if FCERR is set to 1, if set to 1, clear it and try the whole
- * sequence a few more times, else read in (shift in) the Flash Data0,
- * the order is least significant byte first msb to lsb */
- if (error == E1000_SUCCESS) {
- flash_data = E1000_READ_ICH_FLASH_REG(hw, ICH_FLASH_FDATA0);
- if (size == 1) {
- *data = (u8)(flash_data & 0x000000FF);
- } else if (size == 2) {
- *data = (u16)(flash_data & 0x0000FFFF);
- }
- break;
- } else {
- /* If we've gotten here, then things are probably completely hosed,
- * but if the error condition is detected, it won't hurt to give
- * it another try...ICH_FLASH_CYCLE_REPEAT_COUNT times.
- */
- hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS);
- if (hsfsts.hsf_status.flcerr == 1) {
- /* Repeat for some time before giving up. */
- continue;
- } else if (hsfsts.hsf_status.flcdone == 0) {
- DEBUGOUT("Timeout error - flash cycle did not complete.");
- break;
- }
- }
- } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT);
-
- return error;
-}
-
-/******************************************************************************
- * Writes One /two bytes to the NVM using the ICH8 flash access registers.
- *
- * hw - The pointer to the hw structure
- * index - The index of the byte/word to read.
- * size - Size of data to read, 1=byte 2=word
- * data - The byte(s) to write to the NVM.
- *****************************************************************************/
-static s32 e1000_write_ich8_data(struct e1000_hw *hw, u32 index, u32 size,
- u16 data)
-{
- union ich8_hws_flash_status hsfsts;
- union ich8_hws_flash_ctrl hsflctl;
- u32 flash_linear_address;
- u32 flash_data = 0;
- s32 error = -E1000_ERR_EEPROM;
- s32 count = 0;
-
- DEBUGFUNC("e1000_write_ich8_data");
-
- if (size < 1 || size > 2 || data > size * 0xff ||
- index > ICH_FLASH_LINEAR_ADDR_MASK)
- return error;
-
- flash_linear_address = (ICH_FLASH_LINEAR_ADDR_MASK & index) +
- hw->flash_base_addr;
-
- do {
- udelay(1);
- /* Steps */
- error = e1000_ich8_cycle_init(hw);
- if (error != E1000_SUCCESS)
- break;
-
- hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL);
- /* 0b/1b corresponds to 1 or 2 byte size, respectively. */
- hsflctl.hsf_ctrl.fldbcount = size -1;
- hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_WRITE;
- E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval);
-
- /* Write the last 24 bits of index into Flash Linear address field in
- * Flash Address */
- E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_address);
-
- if (size == 1)
- flash_data = (u32)data & 0x00FF;
- else
- flash_data = (u32)data;
-
- E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FDATA0, flash_data);
-
- /* check if FCERR is set to 1 , if set to 1, clear it and try the whole
- * sequence a few more times else done */
- error = e1000_ich8_flash_cycle(hw, ICH_FLASH_COMMAND_TIMEOUT);
- if (error == E1000_SUCCESS) {
- break;
- } else {
- /* If we're here, then things are most likely completely hosed,
- * but if the error condition is detected, it won't hurt to give
- * it another try...ICH_FLASH_CYCLE_REPEAT_COUNT times.
- */
- hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS);
- if (hsfsts.hsf_status.flcerr == 1) {
- /* Repeat for some time before giving up. */
- continue;
- } else if (hsfsts.hsf_status.flcdone == 0) {
- DEBUGOUT("Timeout error - flash cycle did not complete.");
- break;
- }
- }
- } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT);
-
- return error;
-}
-
-/******************************************************************************
- * Reads a single byte from the NVM using the ICH8 flash access registers.
- *
- * hw - pointer to e1000_hw structure
- * index - The index of the byte to read.
- * data - Pointer to a byte to store the value read.
- *****************************************************************************/
-static s32 e1000_read_ich8_byte(struct e1000_hw *hw, u32 index, u8 *data)
-{
- s32 status = E1000_SUCCESS;
- u16 word = 0;
-
- status = e1000_read_ich8_data(hw, index, 1, &word);
- if (status == E1000_SUCCESS) {
- *data = (u8)word;
- }
-
- return status;
-}
-
-/******************************************************************************
- * Writes a single byte to the NVM using the ICH8 flash access registers.
- * Performs verification by reading back the value and then going through
- * a retry algorithm before giving up.
- *
- * hw - pointer to e1000_hw structure
- * index - The index of the byte to write.
- * byte - The byte to write to the NVM.
- *****************************************************************************/
-static s32 e1000_verify_write_ich8_byte(struct e1000_hw *hw, u32 index, u8 byte)
-{
- s32 error = E1000_SUCCESS;
- s32 program_retries = 0;
-
- DEBUGOUT2("Byte := %2.2X Offset := %d\n", byte, index);
-
- error = e1000_write_ich8_byte(hw, index, byte);
-
- if (error != E1000_SUCCESS) {
- for (program_retries = 0; program_retries < 100; program_retries++) {
- DEBUGOUT2("Retrying \t Byte := %2.2X Offset := %d\n", byte, index);
- error = e1000_write_ich8_byte(hw, index, byte);
- udelay(100);
- if (error == E1000_SUCCESS)
- break;
- }
- }
-
- if (program_retries == 100)
- error = E1000_ERR_EEPROM;
-
- return error;
-}
-
-/******************************************************************************
- * Writes a single byte to the NVM using the ICH8 flash access registers.
- *
- * hw - pointer to e1000_hw structure
- * index - The index of the byte to read.
- * data - The byte to write to the NVM.
- *****************************************************************************/
-static s32 e1000_write_ich8_byte(struct e1000_hw *hw, u32 index, u8 data)
-{
- s32 status = E1000_SUCCESS;
- u16 word = (u16)data;
-
- status = e1000_write_ich8_data(hw, index, 1, word);
-
- return status;
-}
-
-/******************************************************************************
- * Reads a word from the NVM using the ICH8 flash access registers.
- *
- * hw - pointer to e1000_hw structure
- * index - The starting byte index of the word to read.
- * data - Pointer to a word to store the value read.
- *****************************************************************************/
-static s32 e1000_read_ich8_word(struct e1000_hw *hw, u32 index, u16 *data)
-{
- s32 status = E1000_SUCCESS;
- status = e1000_read_ich8_data(hw, index, 2, data);
- return status;
-}
-
-/******************************************************************************
- * Erases the bank specified. Each bank may be a 4, 8 or 64k block. Banks are 0
- * based.
- *
- * hw - pointer to e1000_hw structure
- * bank - 0 for first bank, 1 for second bank
- *
- * Note that this function may actually erase as much as 8 or 64 KBytes. The
- * amount of NVM used in each bank is a *minimum* of 4 KBytes, but in fact the
- * bank size may be 4, 8 or 64 KBytes
- *****************************************************************************/
-static s32 e1000_erase_ich8_4k_segment(struct e1000_hw *hw, u32 bank)
-{
- union ich8_hws_flash_status hsfsts;
- union ich8_hws_flash_ctrl hsflctl;
- u32 flash_linear_address;
- s32 count = 0;
- s32 error = E1000_ERR_EEPROM;
- s32 iteration;
- s32 sub_sector_size = 0;
- s32 bank_size;
- s32 j = 0;
- s32 error_flag = 0;
-
- hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS);
-
- /* Determine HW Sector size: Read BERASE bits of Hw flash Status register */
- /* 00: The Hw sector is 256 bytes, hence we need to erase 16
- * consecutive sectors. The start index for the nth Hw sector can be
- * calculated as bank * 4096 + n * 256
- * 01: The Hw sector is 4K bytes, hence we need to erase 1 sector.
- * The start index for the nth Hw sector can be calculated
- * as bank * 4096
- * 10: The HW sector is 8K bytes
- * 11: The Hw sector size is 64K bytes */
- if (hsfsts.hsf_status.berasesz == 0x0) {
- /* Hw sector size 256 */
- sub_sector_size = ICH_FLASH_SEG_SIZE_256;
- bank_size = ICH_FLASH_SECTOR_SIZE;
- iteration = ICH_FLASH_SECTOR_SIZE / ICH_FLASH_SEG_SIZE_256;
- } else if (hsfsts.hsf_status.berasesz == 0x1) {
- bank_size = ICH_FLASH_SEG_SIZE_4K;
- iteration = 1;
- } else if (hsfsts.hsf_status.berasesz == 0x3) {
- bank_size = ICH_FLASH_SEG_SIZE_64K;
- iteration = 1;
- } else {
- return error;
- }
-
- for (j = 0; j < iteration ; j++) {
- do {
- count++;
- /* Steps */
- error = e1000_ich8_cycle_init(hw);
- if (error != E1000_SUCCESS) {
- error_flag = 1;
- break;
- }
-
- /* Write a value 11 (block Erase) in Flash Cycle field in Hw flash
- * Control */
- hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL);
- hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_ERASE;
- E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval);
-
- /* Write the last 24 bits of an index within the block into Flash
- * Linear address field in Flash Address. This probably needs to
- * be calculated here based off the on-chip erase sector size and
- * the software bank size (4, 8 or 64 KBytes) */
- flash_linear_address = bank * bank_size + j * sub_sector_size;
- flash_linear_address += hw->flash_base_addr;
- flash_linear_address &= ICH_FLASH_LINEAR_ADDR_MASK;
-
- E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_address);
-
- error = e1000_ich8_flash_cycle(hw, ICH_FLASH_ERASE_TIMEOUT);
- /* Check if FCERR is set to 1. If 1, clear it and try the whole
- * sequence a few more times else Done */
- if (error == E1000_SUCCESS) {
- break;
- } else {
- hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS);
- if (hsfsts.hsf_status.flcerr == 1) {
- /* repeat for some time before giving up */
- continue;
- } else if (hsfsts.hsf_status.flcdone == 0) {
- error_flag = 1;
- break;
- }
- }
- } while ((count < ICH_FLASH_CYCLE_REPEAT_COUNT) && !error_flag);
- if (error_flag == 1)
- break;
- }
- if (error_flag != 1)
- error = E1000_SUCCESS;
- return error;
-}
-
-static s32 e1000_init_lcd_from_nvm_config_region(struct e1000_hw *hw,
- u32 cnf_base_addr,
- u32 cnf_size)
-{
- u32 ret_val = E1000_SUCCESS;
- u16 word_addr, reg_data, reg_addr;
- u16 i;
-
- /* cnf_base_addr is in DWORD */
- word_addr = (u16)(cnf_base_addr << 1);
-
- /* cnf_size is returned in size of dwords */
- for (i = 0; i < cnf_size; i++) {
- ret_val = e1000_read_eeprom(hw, (word_addr + i*2), 1, ®_data);
- if (ret_val)
- return ret_val;
-
- ret_val = e1000_read_eeprom(hw, (word_addr + i*2 + 1), 1, ®_addr);
- if (ret_val)
- return ret_val;
-
- ret_val = e1000_get_software_flag(hw);
- if (ret_val != E1000_SUCCESS)
- return ret_val;
-
- ret_val = e1000_write_phy_reg_ex(hw, (u32)reg_addr, reg_data);
-
- e1000_release_software_flag(hw);
- }
-
- return ret_val;
-}
-
-
-/******************************************************************************
- * This function initializes the PHY from the NVM on ICH8 platforms. This
- * is needed due to an issue where the NVM configuration is not properly
- * autoloaded after power transitions. Therefore, after each PHY reset, we
- * will load the configuration data out of the NVM manually.
- *
- * hw: Struct containing variables accessed by shared code
- *****************************************************************************/
-static s32 e1000_init_lcd_from_nvm(struct e1000_hw *hw)
-{
- u32 reg_data, cnf_base_addr, cnf_size, ret_val, loop;
-
- if (hw->phy_type != e1000_phy_igp_3)
- return E1000_SUCCESS;
-
- /* Check if SW needs configure the PHY */
- reg_data = er32(FEXTNVM);
- if (!(reg_data & FEXTNVM_SW_CONFIG))
- return E1000_SUCCESS;
-
- /* Wait for basic configuration completes before proceeding*/
- loop = 0;
- do {
- reg_data = er32(STATUS) & E1000_STATUS_LAN_INIT_DONE;
- udelay(100);
- loop++;
- } while ((!reg_data) && (loop < 50));
-
- /* Clear the Init Done bit for the next init event */
- reg_data = er32(STATUS);
- reg_data &= ~E1000_STATUS_LAN_INIT_DONE;
- ew32(STATUS, reg_data);
-
- /* Make sure HW does not configure LCD from PHY extended configuration
- before SW configuration */
- reg_data = er32(EXTCNF_CTRL);
- if ((reg_data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE) == 0x0000) {
- reg_data = er32(EXTCNF_SIZE);
- cnf_size = reg_data & E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH;
- cnf_size >>= 16;
- if (cnf_size) {
- reg_data = er32(EXTCNF_CTRL);
- cnf_base_addr = reg_data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER;
- /* cnf_base_addr is in DWORD */
- cnf_base_addr >>= 16;
-
- /* Configure LCD from extended configuration region. */
- ret_val = e1000_init_lcd_from_nvm_config_region(hw, cnf_base_addr,
- cnf_size);
- if (ret_val)
- return ret_val;
- }
- }
-
- return E1000_SUCCESS;
-}
-
git.openpandora.org / pandora-kernel.git / blobdiff