'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.
The driver supports multiple bonding modes to allow for both high
- perfomance and high availability operation.
+ performance and high availability operation.
Refer to <file:Documentation/networking/bonding.txt> for more
information.
config MIPS_AU1X00_ENET
bool "MIPS AU1000 Ethernet support"
depends on NET_ETHERNET && SOC_AU1X00
+ select PHYLIB
select CRC32
help
If you have an Alchemy Semi AU1X00 based system
depends on NET_VENDOR_3COM && (PCI || EISA)
select MII
---help---
- This option enables driver support for a large number of 10mbps and
- 10/100mbps EISA, PCI and PCMCIA 3Com network cards:
+ This option enables driver support for a large number of 10Mbps and
+ 10/100Mbps EISA, PCI and PCMCIA 3Com network cards:
"Vortex" (Fast EtherLink 3c590/3c592/3c595/3c597) EISA and PCI
"Boomerang" (EtherLink XL 3c900 or 3c905) PCI
<file:Documentation/networking/net-modules.txt>. The module will be
called dm9000.
+config SMC911X
+ tristate "SMSC LAN911[5678] support"
+ select CRC32
+ select MII
+ depends on NET_ETHERNET && ARCH_PXA
+ help
+ This is a driver for SMSC's LAN911x series of Ethernet chipsets
+ including the new LAN9115, LAN9116, LAN9117, and LAN9118.
+ Say Y if you want it compiled into the kernel,
+ and read the Ethernet-HOWTO, available from
+ <http://www.linuxdoc.org/docs.html#howto>.
+
+ This driver is also available as a module. The module will be
+ called smc911x. If you want to compile it as a module, say M
+ here and read <file:Documentation/modules.txt>
+
config NET_VENDOR_RACAL
bool "Racal-Interlan (Micom) NI cards"
depends on NET_ETHERNET && ISA
depends on NET_ISA
---help---
If you have a network (Ethernet) card of this type, say Y. This
- driver supports intel i82595{FX,TX} based boards. Note however
+ driver supports Intel i82595{FX,TX} based boards. Note however
that the EtherExpress PRO/100 Ethernet card has its own separate
driver. Please read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
help
Additional receive skb headroom. Note, that driver
will always reserve at least 2 bytes to make IP header
- aligned, so usualy there is no need to add any additional
+ aligned, so usually there is no need to add any additional
headroom.
If unsure, set to 0.
called b44.
config FORCEDETH
- tristate "Reverse Engineered nForce Ethernet support (EXPERIMENTAL)"
- depends on NET_PCI && PCI && EXPERIMENTAL
+ tristate "nForce Ethernet support"
+ depends on NET_PCI && PCI
help
If you have a network (Ethernet) controller of this type, say Y and
read the Ethernet-HOWTO, available from
---help---
This is a driver for the Fast Ethernet PCI network cards based on
the SiS 900 and SiS 7016 chips. The SiS 900 core is also embedded in
- SiS 630 and SiS 540 chipsets. If you have one of those, say Y and
- read the Ethernet-HOWTO, available at
- <http://www.tldp.org/docs.html#howto>. Please read
- <file:Documentation/networking/sis900.txt> and comments at the
- beginning of <file:drivers/net/sis900.c> for more information.
+ SiS 630 and SiS 540 chipsets.
This driver also supports AMD 79C901 HomePNA so that you can use
your phone line as a network cable.
depends on E1000
help
Say Y here if you want to use the legacy receive path for PCI express
- hadware.
+ hardware.
If in doubt, say N.
will be called myri_sbus. This is recommended.
config NS83820
- tristate "National Semiconduct DP83820 support"
+ tristate "National Semiconductor DP83820 support"
depends on PCI
help
This is a driver for the National Semiconductor DP83820 series
config MV643XX_ETH
tristate "MV-643XX Ethernet support"
depends on MOMENCO_OCELOT_C || MOMENCO_JAGUAR_ATX || MV64360 || MOMENCO_OCELOT_3 || PPC_MULTIPLATFORM
+ select MII
help
This driver supports the gigabit Ethernet on the Marvell MV643XX
chipset which is used in the Momenco Ocelot C and Jaguar ATX and
If in doubt, say N.
+config MYRI10GE
+ tristate "Myricom Myri-10G Ethernet support"
+ depends on PCI
+ select FW_LOADER
+ select CRC32
+ ---help---
+ This driver supports Myricom Myri-10G Dual Protocol interface in
+ Ethernet mode. If the eeprom on your board is not recent enough,
+ you will need a newer firmware image.
+ You may get this image or more information, at:
+
+ <http://www.myri.com/Myri-10G/>
+
+ To compile this driver as a module, choose M here and read
+ <file:Documentation/networking/net-modules.txt>. The module
+ will be called myri10ge.
+
endmenu
-if !UML
source "drivers/net/tokenring/Kconfig"
source "drivers/net/wireless/Kconfig"
source "drivers/net/pcmcia/Kconfig"
-endif
source "drivers/net/wan/Kconfig"
Say Y here if you want to be able to filter the packets passing over
PPP interfaces. This allows you to control which packets count as
activity (i.e. which packets will reset the idle timer or bring up
- a demand-dialled link) and which packets are to be dropped entirely.
+ a demand-dialed link) and which packets are to be dropped entirely.
You need to say Y here if you wish to use the pass-filter and
active-filter options to pppd.
<file:Documentation/networking/shaper.txt> for more information.
An alternative to this traffic shaper is the experimental
- Class-Based Queueing (CBQ) scheduling support which you get if you
- say Y to "QoS and/or fair queueing" above.
+ Class-Based Queuing (CBQ) scheduling support which you get if you
+ say Y to "QoS and/or fair queuing" above.
To compile this driver as a module, choose M here: the module
will be called shaper. If unsure, say N.
git.openpandora.org / pandora-kernel.git / blobdiff