*
* License Terms: GNU General Public License v2
* Author: Arun R Murthy <arun.murthy@stericsson.com>
+ * Author: Daniel Willerud <daniel.willerud@stericsson.com>
+ * Author: Johan Palsson <johan.palsson@stericsson.com>
*/
#include <linux/init.h>
#include <linux/module.h>
#include <linux/regulator/consumer.h>
#include <linux/err.h>
#include <linux/slab.h>
+#include <linux/list.h>
#include <linux/mfd/ab8500.h>
#include <linux/mfd/abx500.h>
-#include <linux/mfd/ab8500/ab8500-gpadc.h>
+#include <linux/mfd/ab8500/gpadc.h>
/*
* GPADC register offsets
#define AB8500_GPADC_AUTODATAH_REG 0x08
#define AB8500_GPADC_MUX_CTRL_REG 0x09
+/*
+ * OTP register offsets
+ * Bank : 0x15
+ */
+#define AB8500_GPADC_CAL_1 0x0F
+#define AB8500_GPADC_CAL_2 0x10
+#define AB8500_GPADC_CAL_3 0x11
+#define AB8500_GPADC_CAL_4 0x12
+#define AB8500_GPADC_CAL_5 0x13
+#define AB8500_GPADC_CAL_6 0x14
+#define AB8500_GPADC_CAL_7 0x15
+
/* gpadc constants */
#define EN_VINTCORE12 0x04
#define EN_VTVOUT 0x02
#define DIS_GPADC 0x00
#define SW_AVG_16 0x60
#define ADC_SW_CONV 0x04
+#define EN_ICHAR 0x80
#define EN_BUF 0x40
#define DIS_ZERO 0x00
#define GPADC_BUSY 0x01
+/* GPADC constants from AB8500 spec, UM0836 */
+#define ADC_RESOLUTION 1024
+#define ADC_CH_BTEMP_MIN 0
+#define ADC_CH_BTEMP_MAX 1350
+#define ADC_CH_DIETEMP_MIN 0
+#define ADC_CH_DIETEMP_MAX 1350
+#define ADC_CH_CHG_V_MIN 0
+#define ADC_CH_CHG_V_MAX 20030
+#define ADC_CH_ACCDET2_MIN 0
+#define ADC_CH_ACCDET2_MAX 2500
+#define ADC_CH_VBAT_MIN 2300
+#define ADC_CH_VBAT_MAX 4800
+#define ADC_CH_CHG_I_MIN 0
+#define ADC_CH_CHG_I_MAX 1500
+#define ADC_CH_BKBAT_MIN 0
+#define ADC_CH_BKBAT_MAX 3200
+
+/* This is used to not lose precision when dividing to get gain and offset */
+#define CALIB_SCALE 1000
+
+enum cal_channels {
+ ADC_INPUT_VMAIN = 0,
+ ADC_INPUT_BTEMP,
+ ADC_INPUT_VBAT,
+ NBR_CAL_INPUTS,
+};
+
/**
- * struct ab8500_gpadc - ab8500 GPADC device information
+ * struct adc_cal_data - Table for storing gain and offset for the calibrated
+ * ADC channels
+ * @gain: Gain of the ADC channel
+ * @offset: Offset of the ADC channel
+ */
+struct adc_cal_data {
+ u64 gain;
+ u64 offset;
+};
+
+/**
+ * struct ab8500_gpadc - AB8500 GPADC device information
* @dev: pointer to the struct device
- * @parent: pointer to the parent device structure ab8500
+ * @node: a list of AB8500 GPADCs, hence prepared for
+ reentrance
* @ab8500_gpadc_complete: pointer to the struct completion, to indicate
* the completion of gpadc conversion
* @ab8500_gpadc_lock: structure of type mutex
* @regu: pointer to the struct regulator
* @irq: interrupt number that is used by gpadc
+ * @cal_data array of ADC calibration data structs
*/
-static struct ab8500_gpadc {
+struct ab8500_gpadc {
struct device *dev;
- struct ab8500 *parent;
+ struct list_head node;
struct completion ab8500_gpadc_complete;
struct mutex ab8500_gpadc_lock;
struct regulator *regu;
int irq;
-} *di;
+ struct adc_cal_data cal_data[NBR_CAL_INPUTS];
+};
+
+static LIST_HEAD(ab8500_gpadc_list);
+
+/**
+ * ab8500_gpadc_get() - returns a reference to the primary AB8500 GPADC
+ * (i.e. the first GPADC in the instance list)
+ */
+struct ab8500_gpadc *ab8500_gpadc_get(char *name)
+{
+ struct ab8500_gpadc *gpadc;
+
+ list_for_each_entry(gpadc, &ab8500_gpadc_list, node) {
+ if (!strcmp(name, dev_name(gpadc->dev)))
+ return gpadc;
+ }
+
+ return ERR_PTR(-ENOENT);
+}
+EXPORT_SYMBOL(ab8500_gpadc_get);
+
+static int ab8500_gpadc_ad_to_voltage(struct ab8500_gpadc *gpadc, u8 input,
+ int ad_value)
+{
+ int res;
+
+ switch (input) {
+ case MAIN_CHARGER_V:
+ /* For some reason we don't have calibrated data */
+ if (!gpadc->cal_data[ADC_INPUT_VMAIN].gain) {
+ res = ADC_CH_CHG_V_MIN + (ADC_CH_CHG_V_MAX -
+ ADC_CH_CHG_V_MIN) * ad_value /
+ ADC_RESOLUTION;
+ break;
+ }
+ /* Here we can use the calibrated data */
+ res = (int) (ad_value * gpadc->cal_data[ADC_INPUT_VMAIN].gain +
+ gpadc->cal_data[ADC_INPUT_VMAIN].offset) / CALIB_SCALE;
+ break;
+
+ case BAT_CTRL:
+ case BTEMP_BALL:
+ case ACC_DETECT1:
+ case ADC_AUX1:
+ case ADC_AUX2:
+ /* For some reason we don't have calibrated data */
+ if (!gpadc->cal_data[ADC_INPUT_BTEMP].gain) {
+ res = ADC_CH_BTEMP_MIN + (ADC_CH_BTEMP_MAX -
+ ADC_CH_BTEMP_MIN) * ad_value /
+ ADC_RESOLUTION;
+ break;
+ }
+ /* Here we can use the calibrated data */
+ res = (int) (ad_value * gpadc->cal_data[ADC_INPUT_BTEMP].gain +
+ gpadc->cal_data[ADC_INPUT_BTEMP].offset) / CALIB_SCALE;
+ break;
+
+ case MAIN_BAT_V:
+ /* For some reason we don't have calibrated data */
+ if (!gpadc->cal_data[ADC_INPUT_VBAT].gain) {
+ res = ADC_CH_VBAT_MIN + (ADC_CH_VBAT_MAX -
+ ADC_CH_VBAT_MIN) * ad_value /
+ ADC_RESOLUTION;
+ break;
+ }
+ /* Here we can use the calibrated data */
+ res = (int) (ad_value * gpadc->cal_data[ADC_INPUT_VBAT].gain +
+ gpadc->cal_data[ADC_INPUT_VBAT].offset) / CALIB_SCALE;
+ break;
+
+ case DIE_TEMP:
+ res = ADC_CH_DIETEMP_MIN +
+ (ADC_CH_DIETEMP_MAX - ADC_CH_DIETEMP_MIN) * ad_value /
+ ADC_RESOLUTION;
+ break;
+
+ case ACC_DETECT2:
+ res = ADC_CH_ACCDET2_MIN +
+ (ADC_CH_ACCDET2_MAX - ADC_CH_ACCDET2_MIN) * ad_value /
+ ADC_RESOLUTION;
+ break;
+
+ case VBUS_V:
+ res = ADC_CH_CHG_V_MIN +
+ (ADC_CH_CHG_V_MAX - ADC_CH_CHG_V_MIN) * ad_value /
+ ADC_RESOLUTION;
+ break;
+
+ case MAIN_CHARGER_C:
+ case USB_CHARGER_C:
+ res = ADC_CH_CHG_I_MIN +
+ (ADC_CH_CHG_I_MAX - ADC_CH_CHG_I_MIN) * ad_value /
+ ADC_RESOLUTION;
+ break;
+
+ case BK_BAT_V:
+ res = ADC_CH_BKBAT_MIN +
+ (ADC_CH_BKBAT_MAX - ADC_CH_BKBAT_MIN) * ad_value /
+ ADC_RESOLUTION;
+ break;
+
+ default:
+ dev_err(gpadc->dev,
+ "unknown channel, not possible to convert\n");
+ res = -EINVAL;
+ break;
+
+ }
+ return res;
+}
/**
* ab8500_gpadc_convert() - gpadc conversion
* @input: analog input to be converted to digital data
*
* This function converts the selected analog i/p to digital
- * data. Thereafter calibration has to be made to obtain the
- * data in the required quantity measurement.
+ * data.
*/
-int ab8500_gpadc_convert(u8 input)
+int ab8500_gpadc_convert(struct ab8500_gpadc *gpadc, u8 input)
{
int ret;
u16 data = 0;
int looplimit = 0;
u8 val, low_data, high_data;
- if (!di)
+ if (!gpadc)
return -ENODEV;
- mutex_lock(&di->ab8500_gpadc_lock);
+ mutex_lock(&gpadc->ab8500_gpadc_lock);
/* Enable VTVout LDO this is required for GPADC */
- regulator_enable(di->regu);
+ regulator_enable(gpadc->regu);
/* Check if ADC is not busy, lock and proceed */
do {
- ret = abx500_get_register_interruptible(di->dev, AB8500_GPADC,
- AB8500_GPADC_STAT_REG, &val);
+ ret = abx500_get_register_interruptible(gpadc->dev,
+ AB8500_GPADC, AB8500_GPADC_STAT_REG, &val);
if (ret < 0)
goto out;
if (!(val & GPADC_BUSY))
msleep(10);
} while (++looplimit < 10);
if (looplimit >= 10 && (val & GPADC_BUSY)) {
- dev_err(di->dev, "gpadc_conversion: GPADC busy");
+ dev_err(gpadc->dev, "gpadc_conversion: GPADC busy");
ret = -EINVAL;
goto out;
}
/* Enable GPADC */
- ret = abx500_mask_and_set_register_interruptible(di->dev, AB8500_GPADC,
- AB8500_GPADC_CTRL1_REG, EN_GPADC, EN_GPADC);
+ ret = abx500_mask_and_set_register_interruptible(gpadc->dev,
+ AB8500_GPADC, AB8500_GPADC_CTRL1_REG, EN_GPADC, EN_GPADC);
if (ret < 0) {
- dev_err(di->dev, "gpadc_conversion: enable gpadc failed\n");
+ dev_err(gpadc->dev, "gpadc_conversion: enable gpadc failed\n");
goto out;
}
/* Select the input source and set average samples to 16 */
- ret = abx500_set_register_interruptible(di->dev, AB8500_GPADC,
+ ret = abx500_set_register_interruptible(gpadc->dev, AB8500_GPADC,
AB8500_GPADC_CTRL2_REG, (input | SW_AVG_16));
if (ret < 0) {
- dev_err(di->dev,
+ dev_err(gpadc->dev,
"gpadc_conversion: set avg samples failed\n");
goto out;
}
- /* Enable ADC, Buffering and select rising edge, start Conversion */
- ret = abx500_mask_and_set_register_interruptible(di->dev, AB8500_GPADC,
- AB8500_GPADC_CTRL1_REG, EN_BUF, EN_BUF);
+ /*
+ * Enable ADC, buffering, select rising edge and enable ADC path
+ * charging current sense if it needed
+ */
+ switch (input) {
+ case MAIN_CHARGER_C:
+ case USB_CHARGER_C:
+ ret = abx500_mask_and_set_register_interruptible(gpadc->dev,
+ AB8500_GPADC, AB8500_GPADC_CTRL1_REG,
+ EN_BUF | EN_ICHAR,
+ EN_BUF | EN_ICHAR);
+ break;
+ default:
+ ret = abx500_mask_and_set_register_interruptible(gpadc->dev,
+ AB8500_GPADC, AB8500_GPADC_CTRL1_REG, EN_BUF, EN_BUF);
+ break;
+ }
if (ret < 0) {
- dev_err(di->dev,
+ dev_err(gpadc->dev,
"gpadc_conversion: select falling edge failed\n");
goto out;
}
- ret = abx500_mask_and_set_register_interruptible(di->dev, AB8500_GPADC,
- AB8500_GPADC_CTRL1_REG, ADC_SW_CONV, ADC_SW_CONV);
+ ret = abx500_mask_and_set_register_interruptible(gpadc->dev,
+ AB8500_GPADC, AB8500_GPADC_CTRL1_REG, ADC_SW_CONV, ADC_SW_CONV);
if (ret < 0) {
- dev_err(di->dev,
+ dev_err(gpadc->dev,
"gpadc_conversion: start s/w conversion failed\n");
goto out;
}
/* wait for completion of conversion */
- if (!wait_for_completion_timeout(&di->ab8500_gpadc_complete, 2*HZ)) {
- dev_err(di->dev,
- "timeout: didnt recieve GPADC conversion interrupt\n");
+ if (!wait_for_completion_timeout(&gpadc->ab8500_gpadc_complete, 2*HZ)) {
+ dev_err(gpadc->dev,
+ "timeout: didn't receive GPADC conversion interrupt\n");
ret = -EINVAL;
goto out;
}
/* Read the converted RAW data */
- ret = abx500_get_register_interruptible(di->dev, AB8500_GPADC,
+ ret = abx500_get_register_interruptible(gpadc->dev, AB8500_GPADC,
AB8500_GPADC_MANDATAL_REG, &low_data);
if (ret < 0) {
- dev_err(di->dev, "gpadc_conversion: read low data failed\n");
+ dev_err(gpadc->dev, "gpadc_conversion: read low data failed\n");
goto out;
}
- ret = abx500_get_register_interruptible(di->dev, AB8500_GPADC,
+ ret = abx500_get_register_interruptible(gpadc->dev, AB8500_GPADC,
AB8500_GPADC_MANDATAH_REG, &high_data);
if (ret < 0) {
- dev_err(di->dev, "gpadc_conversion: read high data failed\n");
+ dev_err(gpadc->dev,
+ "gpadc_conversion: read high data failed\n");
goto out;
}
data = (high_data << 8) | low_data;
/* Disable GPADC */
- ret = abx500_set_register_interruptible(di->dev, AB8500_GPADC,
+ ret = abx500_set_register_interruptible(gpadc->dev, AB8500_GPADC,
AB8500_GPADC_CTRL1_REG, DIS_GPADC);
if (ret < 0) {
- dev_err(di->dev, "gpadc_conversion: disable gpadc failed\n");
+ dev_err(gpadc->dev, "gpadc_conversion: disable gpadc failed\n");
goto out;
}
/* Disable VTVout LDO this is required for GPADC */
- regulator_disable(di->regu);
- mutex_unlock(&di->ab8500_gpadc_lock);
- return data;
+ regulator_disable(gpadc->regu);
+ mutex_unlock(&gpadc->ab8500_gpadc_lock);
+ ret = ab8500_gpadc_ad_to_voltage(gpadc, input, data);
+ return ret;
out:
/*
* GPADC status register to go low. In V1.1 there wait_for_completion
* seems to timeout when waiting for an interrupt.. Not seen in V2.0
*/
- (void) abx500_set_register_interruptible(di->dev, AB8500_GPADC,
+ (void) abx500_set_register_interruptible(gpadc->dev, AB8500_GPADC,
AB8500_GPADC_CTRL1_REG, DIS_GPADC);
- regulator_disable(di->regu);
- mutex_unlock(&di->ab8500_gpadc_lock);
- dev_err(di->dev, "gpadc_conversion: Failed to AD convert channel %d\n",
- input);
+ regulator_disable(gpadc->regu);
+ mutex_unlock(&gpadc->ab8500_gpadc_lock);
+ dev_err(gpadc->dev,
+ "gpadc_conversion: Failed to AD convert channel %d\n", input);
return ret;
}
EXPORT_SYMBOL(ab8500_gpadc_convert);
* can be read from the registers.
* Returns IRQ status(IRQ_HANDLED)
*/
-static irqreturn_t ab8500_bm_gpswadcconvend_handler(int irq, void *_di)
+static irqreturn_t ab8500_bm_gpswadcconvend_handler(int irq, void *_gpadc)
{
- struct ab8500_gpadc *gpadc = _di;
+ struct ab8500_gpadc *gpadc = _gpadc;
complete(&gpadc->ab8500_gpadc_complete);
return IRQ_HANDLED;
}
+static int otp_cal_regs[] = {
+ AB8500_GPADC_CAL_1,
+ AB8500_GPADC_CAL_2,
+ AB8500_GPADC_CAL_3,
+ AB8500_GPADC_CAL_4,
+ AB8500_GPADC_CAL_5,
+ AB8500_GPADC_CAL_6,
+ AB8500_GPADC_CAL_7,
+};
+
+static void ab8500_gpadc_read_calibration_data(struct ab8500_gpadc *gpadc)
+{
+ int i;
+ int ret[ARRAY_SIZE(otp_cal_regs)];
+ u8 gpadc_cal[ARRAY_SIZE(otp_cal_regs)];
+
+ int vmain_high, vmain_low;
+ int btemp_high, btemp_low;
+ int vbat_high, vbat_low;
+
+ /* First we read all OTP registers and store the error code */
+ for (i = 0; i < ARRAY_SIZE(otp_cal_regs); i++) {
+ ret[i] = abx500_get_register_interruptible(gpadc->dev,
+ AB8500_OTP_EMUL, otp_cal_regs[i], &gpadc_cal[i]);
+ if (ret[i] < 0)
+ dev_err(gpadc->dev, "%s: read otp reg 0x%02x failed\n",
+ __func__, otp_cal_regs[i]);
+ }
+
+ /*
+ * The ADC calibration data is stored in OTP registers.
+ * The layout of the calibration data is outlined below and a more
+ * detailed description can be found in UM0836
+ *
+ * vm_h/l = vmain_high/low
+ * bt_h/l = btemp_high/low
+ * vb_h/l = vbat_high/low
+ *
+ * Data bits:
+ * | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0
+ * |.......|.......|.......|.......|.......|.......|.......|.......
+ * | | vm_h9 | vm_h8
+ * |.......|.......|.......|.......|.......|.......|.......|.......
+ * | | vm_h7 | vm_h6 | vm_h5 | vm_h4 | vm_h3 | vm_h2
+ * |.......|.......|.......|.......|.......|.......|.......|.......
+ * | vm_h1 | vm_h0 | vm_l4 | vm_l3 | vm_l2 | vm_l1 | vm_l0 | bt_h9
+ * |.......|.......|.......|.......|.......|.......|.......|.......
+ * | bt_h8 | bt_h7 | bt_h6 | bt_h5 | bt_h4 | bt_h3 | bt_h2 | bt_h1
+ * |.......|.......|.......|.......|.......|.......|.......|.......
+ * | bt_h0 | bt_l4 | bt_l3 | bt_l2 | bt_l1 | bt_l0 | vb_h9 | vb_h8
+ * |.......|.......|.......|.......|.......|.......|.......|.......
+ * | vb_h7 | vb_h6 | vb_h5 | vb_h4 | vb_h3 | vb_h2 | vb_h1 | vb_h0
+ * |.......|.......|.......|.......|.......|.......|.......|.......
+ * | vb_l5 | vb_l4 | vb_l3 | vb_l2 | vb_l1 | vb_l0 |
+ * |.......|.......|.......|.......|.......|.......|.......|.......
+ *
+ *
+ * Ideal output ADC codes corresponding to injected input voltages
+ * during manufacturing is:
+ *
+ * vmain_high: Vin = 19500mV / ADC ideal code = 997
+ * vmain_low: Vin = 315mV / ADC ideal code = 16
+ * btemp_high: Vin = 1300mV / ADC ideal code = 985
+ * btemp_low: Vin = 21mV / ADC ideal code = 16
+ * vbat_high: Vin = 4700mV / ADC ideal code = 982
+ * vbat_low: Vin = 2380mV / ADC ideal code = 33
+ */
+
+ /* Calculate gain and offset for VMAIN if all reads succeeded */
+ if (!(ret[0] < 0 || ret[1] < 0 || ret[2] < 0)) {
+ vmain_high = (((gpadc_cal[0] & 0x03) << 8) |
+ ((gpadc_cal[1] & 0x3F) << 2) |
+ ((gpadc_cal[2] & 0xC0) >> 6));
+
+ vmain_low = ((gpadc_cal[2] & 0x3E) >> 1);
+
+ gpadc->cal_data[ADC_INPUT_VMAIN].gain = CALIB_SCALE *
+ (19500 - 315) / (vmain_high - vmain_low);
+
+ gpadc->cal_data[ADC_INPUT_VMAIN].offset = CALIB_SCALE * 19500 -
+ (CALIB_SCALE * (19500 - 315) /
+ (vmain_high - vmain_low)) * vmain_high;
+ } else {
+ gpadc->cal_data[ADC_INPUT_VMAIN].gain = 0;
+ }
+
+ /* Calculate gain and offset for BTEMP if all reads succeeded */
+ if (!(ret[2] < 0 || ret[3] < 0 || ret[4] < 0)) {
+ btemp_high = (((gpadc_cal[2] & 0x01) << 9) |
+ (gpadc_cal[3] << 1) |
+ ((gpadc_cal[4] & 0x80) >> 7));
+
+ btemp_low = ((gpadc_cal[4] & 0x7C) >> 2);
+
+ gpadc->cal_data[ADC_INPUT_BTEMP].gain =
+ CALIB_SCALE * (1300 - 21) / (btemp_high - btemp_low);
+
+ gpadc->cal_data[ADC_INPUT_BTEMP].offset = CALIB_SCALE * 1300 -
+ (CALIB_SCALE * (1300 - 21) /
+ (btemp_high - btemp_low)) * btemp_high;
+ } else {
+ gpadc->cal_data[ADC_INPUT_BTEMP].gain = 0;
+ }
+
+ /* Calculate gain and offset for VBAT if all reads succeeded */
+ if (!(ret[4] < 0 || ret[5] < 0 || ret[6] < 0)) {
+ vbat_high = (((gpadc_cal[4] & 0x03) << 8) | gpadc_cal[5]);
+ vbat_low = ((gpadc_cal[6] & 0xFC) >> 2);
+
+ gpadc->cal_data[ADC_INPUT_VBAT].gain = CALIB_SCALE *
+ (4700 - 2380) / (vbat_high - vbat_low);
+
+ gpadc->cal_data[ADC_INPUT_VBAT].offset = CALIB_SCALE * 4700 -
+ (CALIB_SCALE * (4700 - 2380) /
+ (vbat_high - vbat_low)) * vbat_high;
+ } else {
+ gpadc->cal_data[ADC_INPUT_VBAT].gain = 0;
+ }
+
+ dev_dbg(gpadc->dev, "VMAIN gain %llu offset %llu\n",
+ gpadc->cal_data[ADC_INPUT_VMAIN].gain,
+ gpadc->cal_data[ADC_INPUT_VMAIN].offset);
+
+ dev_dbg(gpadc->dev, "BTEMP gain %llu offset %llu\n",
+ gpadc->cal_data[ADC_INPUT_BTEMP].gain,
+ gpadc->cal_data[ADC_INPUT_BTEMP].offset);
+
+ dev_dbg(gpadc->dev, "VBAT gain %llu offset %llu\n",
+ gpadc->cal_data[ADC_INPUT_VBAT].gain,
+ gpadc->cal_data[ADC_INPUT_VBAT].offset);
+}
+
static int __devinit ab8500_gpadc_probe(struct platform_device *pdev)
{
int ret = 0;
return -ENOMEM;
}
- gpadc->parent = dev_get_drvdata(pdev->dev.parent);
gpadc->irq = platform_get_irq_byname(pdev, "SW_CONV_END");
if (gpadc->irq < 0) {
- dev_err(gpadc->dev, "failed to get platform irq-%d\n", di->irq);
+ dev_err(gpadc->dev, "failed to get platform irq-%d\n",
+ gpadc->irq);
ret = gpadc->irq;
goto fail;
}
gpadc->dev = &pdev->dev;
- mutex_init(&di->ab8500_gpadc_lock);
+ mutex_init(&gpadc->ab8500_gpadc_lock);
/* Initialize completion used to notify completion of conversion */
init_completion(&gpadc->ab8500_gpadc_complete);
if (IS_ERR(gpadc->regu)) {
ret = PTR_ERR(gpadc->regu);
dev_err(gpadc->dev, "failed to get vtvout LDO\n");
- goto fail;
+ goto fail_irq;
}
- di = gpadc;
+ ab8500_gpadc_read_calibration_data(gpadc);
+ list_add_tail(&gpadc->node, &ab8500_gpadc_list);
dev_dbg(gpadc->dev, "probe success\n");
return 0;
+fail_irq:
+ free_irq(gpadc->irq, gpadc);
fail:
kfree(gpadc);
gpadc = NULL;
{
struct ab8500_gpadc *gpadc = platform_get_drvdata(pdev);
+ /* remove this gpadc entry from the list */
+ list_del(&gpadc->node);
/* remove interrupt - completion of Sw ADC conversion */
- free_irq(gpadc->irq, di);
+ free_irq(gpadc->irq, gpadc);
/* disable VTVout LDO that is being used by GPADC */
regulator_put(gpadc->regu);
kfree(gpadc);
module_exit(ab8500_gpadc_exit);
MODULE_LICENSE("GPL v2");
-MODULE_AUTHOR("Arun R Murthy");
+MODULE_AUTHOR("Arun R Murthy, Daniel Willerud, Johan Palsson");
MODULE_ALIAS("platform:ab8500_gpadc");
MODULE_DESCRIPTION("AB8500 GPADC driver");
git.openpandora.org / pandora-kernel.git / blobdiff