Support for Compact Flash cards, outboard IDE disks, tape drives,
and CD-ROM drives connected through a PCMCIA card.
+config BLK_DEV_DELKIN
+ tristate "Cardbus IDE support (Delkin/ASKA/Workbit)"
+ depends on CARDBUS && PCI
+ help
+ Support for Delkin, ASKA, and Workbit Cardbus CompactFlash
+ Adapters. This may also work for similar SD and XD adapters.
+
config BLK_DEV_IDECD
tristate "Include IDE/ATAPI CDROM support"
---help---
If both this SCSI emulation and native ATAPI support are compiled
into the kernel, the native support will be used.
+config BLK_DEV_IDEACPI
+ bool "IDE ACPI support"
+ depends on ACPI
+ ---help---
+ Implement ACPI support for generic IDE devices. On modern
+ machines ACPI support is required to properly handle ACPI S3 states.
+
config IDE_TASK_IOCTL
bool "IDE Taskfile Access"
help
config BLK_DEV_GENERIC
tristate "Generic PCI IDE Chipset Support"
depends on BLK_DEV_IDEPCI
+ help
+ This option provides generic support for various PCI IDE Chipsets
+ which otherwise might not be supported.
config BLK_DEV_OPTI621
tristate "OPTi 82C621 chipset enhanced support (EXPERIMENTAL)"
Generally say N here.
-config IDEDMA_PCI_AUTO
- bool "Use PCI DMA by default when available"
- ---help---
- Prior to kernel version 2.1.112, Linux used to automatically use
- DMA for IDE drives and chipsets which support it. Due to concerns
- about a couple of cases where buggy hardware may have caused damage,
- the default is now to NOT use DMA automatically. To revert to the
- previous behaviour, say Y to this question.
-
- If you suspect your hardware is at all flakey, say N here.
- Do NOT email the IDE kernel people regarding this issue!
-
- It is normally safe to answer Y to this question unless your
- motherboard uses a VIA VP2 chipset, in which case you should say N.
-
config IDEDMA_ONLYDISK
bool "Enable DMA only for disks "
- depends on IDEDMA_PCI_AUTO
help
This is used if you know your ATAPI Devices are going to fail DMA
Transfers.
the kernel to change PIO, DMA and UDMA speeds and to configure
the chip to optimum performance.
+config BLK_DEV_IT8213
+ tristate "IT8213 IDE support"
+ help
+ This driver adds support for the ITE 8213 IDE controller.
+
config BLK_DEV_IT821X
tristate "IT821X IDE support"
help
This allows the kernel to change PIO, DMA and UDMA speeds and to
configure the chip to optimum performance.
+config BLK_DEV_TC86C001
+ tristate "Toshiba TC86C001 support"
+ help
+ This driver adds support for Toshiba TC86C001 GOKU-S chip.
+
+config BLK_DEV_CELLEB
+ tristate "Toshiba's Cell Reference Set IDE support"
+ depends on PPC_CELLEB
+ help
+ This driver provides support for the built-in IDE controller on
+ Toshiba Cell Reference Board.
+ If unsure, say Y.
+
endif
config BLK_DEV_IDE_PMAC
Say Y here if you want to add DMA (Direct Memory Access) support to
the ICS IDE driver.
-config IDEDMA_ICS_AUTO
- bool "Use ICS DMA by default"
- depends on BLK_DEV_IDEDMA_ICS
- help
- Prior to kernel version 2.1.112, Linux used to automatically use
- DMA for IDE drives and chipsets which support it. Due to concerns
- about a couple of cases where buggy hardware may have caused damage,
- the default is now to NOT use DMA automatically. To revert to the
- previous behaviour, say Y to this question.
-
- If you suspect your hardware is at all flakey, say N here.
- Do NOT email the IDE kernel people regarding this issue!
-
config BLK_DEV_IDE_RAPIDE
tristate "RapIDE interface support"
depends on ARM && ARCH_ACORN
config BLK_DEV_ALI14XX
tristate "ALI M14xx support"
help
- This driver is enabled at runtime using the "ide0=ali14xx" kernel
+ This driver is enabled at runtime using the "ali14xx.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the ALI M1439/1443/1445/1487/1489 chipsets, and permits faster
I/O speeds to be set as well. See the files
config BLK_DEV_DTC2278
tristate "DTC-2278 support"
help
- This driver is enabled at runtime using the "ide0=dtc2278" kernel
+ This driver is enabled at runtime using the "dtc2278.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the DTC-2278 card, and permits faster I/O speeds to be set as
well. See the <file:Documentation/ide.txt> and
config BLK_DEV_HT6560B
tristate "Holtek HT6560B support"
help
- This driver is enabled at runtime using the "ide0=ht6560b" kernel
+ This driver is enabled at runtime using the "ht6560b.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the Holtek card, and permits faster I/O speeds to be set as well.
See the <file:Documentation/ide.txt> and
config BLK_DEV_QD65XX
tristate "QDI QD65xx support"
help
- This driver is enabled at runtime using the "ide0=qd65xx" kernel
+ This driver is enabled at runtime using the "qd65xx.probe" kernel
boot parameter. It permits faster I/O speeds to be set. See the
<file:Documentation/ide.txt> and <file:drivers/ide/legacy/qd65xx.c> for
more info.
config BLK_DEV_UMC8672
tristate "UMC-8672 support"
help
- This driver is enabled at runtime using the "ide0=umc8672" kernel
+ This driver is enabled at runtime using the "umc8672.probe" kernel
boot parameter. It enables support for the secondary IDE interface
of the UMC-8672, and permits faster I/O speeds to be set as well.
See the files <file:Documentation/ide.txt> and
It is normally safe to answer Y; however, the default is N.
-config IDEDMA_AUTO
- def_bool IDEDMA_PCI_AUTO || IDEDMA_ICS_AUTO
-
endif
config BLK_DEV_HD_ONLY
git.openpandora.org / pandora-kernel.git / blobdiff